Current-Users archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index][Old Index]
Nouveau displays scrambled console on Dell Latitude E6400 laptop
Tom Ivar Helbekkmo <tih%hamartun.priv.no@localhost> writes:
> Tom Ivar Helbekkmo <tih%hamartun.priv.no@localhost> writes:
>
>> nouveaufb0 at nouveau0
>> nouveau0: info: registered panic notifier
>>
>> ...and then it just sits there.
>
> Oops! Turns out it's not hung, it's just not displaying its console.
Oops again! The laptop had a really outdated BIOS. Upgrading gets me
to a situation where nouveau tries to use the monitor for a console, but
fails to bitmap it properly, so the screen looks like a psychedelic work
of art. :)
I also get some nouveau driver error messages. /var/run/dmesg.boot:
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 7.99.32 (DEJAH) #1: Sat Jul 2 09:24:33 CEST 2016
root%barsoom.hamartun.priv.no@localhost:/usr/obj/sys/arch/amd64/compile.amd64/DEJAH
total memory = 4083 MB
avail memory = 3944 MB
timecounter: Timecounters tick every 10.000 msec
Kernelized RAIDframe activated
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
Dell Inc. Latitude E6400
mainbus0 (root)
ACPI: RSDP 0x00000000000FB9C0 000024 (v02 DELL )
ACPI: XSDT 0x00000000DF451E00 00006C (v01 DELL M09 27DD0604 ASL 00000061)
ACPI: FACP 0x00000000DF451C9C 0000F4 (v04 DELL M09 27DD0604 ASL 00000061)
ACPI BIOS Warning (bug): 32/64X length mismatch in FADT/Gpe0Block: 128/64 (20160422/tbfadt-652)
ACPI: DSDT 0x00000000DF452400 006E14 (v02 INT430 SYSFexxx 00001001 INTL 20050624)
ACPI: FACS 0x00000000DF460C00 000040
ACPI: FACS 0x00000000DF460C00 000040
ACPI: HPET 0x00000000DF451F00 000038 (v01 DELL M09 00000001 ASL 00000061)
ACPI: ____ 0x00000000DF460400 000030 (v01 DELL M09 27DD0604 ASL 00000061)
ACPI: APIC 0x00000000DF452000 000068 (v01 DELL M09 27DD0604 ASL 00000047)
ACPI: ASF! 0x00000000DF451C00 00006A (v32 DELL M09 27DD0604 ASL 00000061)
ACPI: MCFG 0x00000000DF451FC0 00003C (v16 DELL M09 27DD0604 ASL 00000061)
ACPI: TCPA 0x00000000DF452300 000032 (v01 00000000 ASL 00000000)
ACPI: SLIC 0x00000000DF45209C 000176 (v01 DELL M09 27DD0604 ASL 00000061)
ACPI: SSDT 0x00000000DF4502EB 00066C (v01 PmRef CpuPm 00003000 INTL 20050624)
ACPI: 2 ACPI AML tables successfully acquired and loaded
ioapic0 at mainbus0 apid 2: pa 0xfec00000, version 0x20, 24 pins
cpu0 at mainbus0 apid 0
cpu0: Intel(R) Core(TM)2 Duo CPU T9600 @ 2.80GHz, id 0x1067a
cpu1 at mainbus0 apid 1
cpu1: Intel(R) Core(TM)2 Duo CPU T9600 @ 2.80GHz, id 0x1067a
acpi0 at mainbus0: Intel ACPICA 20160422
acpi0: X/RSDT: OemId <DELL , M09 ,27dd0604>, AslId <ASL ,00000061>
acpi0: MCFG: segment 0, bus 0-63, address 0x00000000f8000000
ACPI: Dynamic OEM Table Load:
ACPI: SSDT 0xFFFFFE811EE91390 0002C3 (v01 PmRef BspIst 00003000 INTL 20050624)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT 0xFFFFFE8107446810 0005C6 (v01 PmRef BspCst 00003001 INTL 20050624)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT 0xFFFFFE81073E4010 0001D7 (v01 PmRef ApIst 00003000 INTL 20050624)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT 0xFFFFFE8107419A48 00008D (v01 PmRef ApCst 00003000 INTL 20050624)
acpi0: SCI interrupting at int 9
timecounter: Timecounter "ACPI-Safe" frequency 3579545 Hz quality 900
hpet0 at acpi0: high precision event timer (mem 0xfed00000-0xfed00400)
timecounter: Timecounter "hpet0" frequency 14318180 Hz quality 2000
acpiec0 at acpi0 (ECDV, PNP0C09-0)
: io 0x930,0x934
pckbc1 at acpi0 (PS2M, PNP0F13) (aux port): irq 12
pckbc2 at acpi0 (KBC, PNP0303) (kbd port): io 0x60,0x64,0x62,0x66 irq 1
attimer1 at acpi0 (TMR, PNP0100): io 0x40-0x43,0x50-0x53 irq 2
pcppi1 at acpi0 (SPKR, PNP0800): io 0x61,0x63,0x65,0x67
midi0 at pcppi1: PC speaker
sysbeep0 at pcppi1
MB4 (PNP0C01) at acpi0 not configured
DIGC (PNP0501) at acpi0 not configured
FTPM (PNP0C01) at acpi0 not configured
acpivga0 at acpi0 (VID): ACPI Display Adapter
acpiout0 at acpivga0 (CRT, 0x0100): ACPI Display Output Device
acpiout1 at acpivga0 (LCD, 0x0110): ACPI Display Output Device
acpiout1: brightness levels: [0,6,13,20,26,33,40,46,53,60,66,73,80,86,93,100]
acpiout2 at acpivga0 (DVI, 0x0112): ACPI Display Output Device
acpiout3 at acpivga0 (DVI2, 0x0111): ACPI Display Output Device
acpiout4 at acpivga0 (DP, 0x0113): ACPI Display Output Device
acpiout5 at acpivga0 (DP2, 0x0114): ACPI Display Output Device
acpivga0: connected output devices:
acpivga0: 0x0100 (acpiout0): Ext. Monitor, head 0
acpivga0: 0x0110 (acpiout1): LCD Panel, head 0
acpivga0: 0x0111 (acpiout3): Unknown Output Device, head 0
acpivga0: 0x0112 (acpiout2): Unknown Output Device, head 0
acpivga0: 0x0113 (acpiout4): Unknown Output Device, head 0
acpivga0: 0x0114 (acpiout5): Unknown Output Device, head 0
MB2 (PNP0C01) at acpi0 not configured
MB3 (PNP0C01) at acpi0 not configured
MB1 (PNP0C01) at acpi0 not configured
acpilid0 at acpi0 (LID, PNP0C0D): ACPI Lid Switch
acpibut0 at acpi0 (PBTN, PNP0C0C): ACPI Power Button
acpibut1 at acpi0 (SBTN, PNP0C0E): ACPI Sleep Button
acpiacad0 at acpi0 (AC, ACPI0003): ACPI AC Adapter
acpibat0 at acpi0 (BAT0, PNP0C0A-1): ACPI Battery
acpibat0: Sanyo LION rechargeable battery
acpibat0: granularity: low->warn 0.052 Ah, warn->full 0.052 Ah
acpibat1 at acpi0 (BAT1, PNP0C0A-2): ACPI Battery
acpiwmi0 at acpi0 (AMW0, PNP0C14-0): ACPI WMI Interface
wmidell0 at acpiwmi0: Dell WMI mappings
ALS (ACPI0008) at acpi0 not configured
acpitz0 at acpi0 (THM)
acpitz0: levels: critical 107.0 C, passive cooling
ACPI: Enabled 3 GPEs in block 00 to 3F
pckbd0 at pckbc2 (kbd slot)
pckbc2: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc2 (aux slot)
pckbc2: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
attimer1: attached to pcppi1
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0: vendor 8086 product 2a40 (rev. 0x07)
agp0 at pchb0: can't find internal VGA config space
ppb0 at pci0 dev 1 function 0: vendor 8086 product 2a41 (rev. 0x07)
ppb0: PCI Express capability version 1 <Root Port of PCI-E Root Complex> x16 @ 2.5GT/s
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
nouveau0 at pci1 dev 0 function 0: vendor 10de product 06eb (rev. 0xa1)
drm kern info: nouveau [ DEVICE][nouveau0] BOOT0 : 0x298580a2
drm kern info: nouveau [ DEVICE][nouveau0] Chipset: G98 (NV98)
drm kern info: nouveau [ DEVICE][nouveau0] Family : NV50
drm kern info: nouveau [ VBIOS][nouveau0] checking PRAMIN for image...
drm kern info: nouveau [ VBIOS][nouveau0] ... appears to be valid
drm kern info: nouveau [ VBIOS][nouveau0] using image from PRAMIN
drm kern info: nouveau [ VBIOS][nouveau0] BIT signature found
drm kern info: nouveau [ VBIOS][nouveau0] version 62.98.3c.00.01
drm kern info: nouveau [ PFB][nouveau0] RAM type: DDR2
drm kern info: nouveau [ PFB][nouveau0] RAM size: 256 MiB
drm kern info: nouveau [ PFB][nouveau0] ZCOMP: 960 tags
drm kern info: nouveau [ VOLT][nouveau0] GPU voltage: 900000uv
drm kern info: nouveau [ PTHERM][nouveau0] FAN control: PWM
drm kern info: nouveau [ PTHERM][nouveau0] fan management: automatic
drm kern info: nouveau [ PTHERM][nouveau0] internal sensor: yes
drm kern info: nouveau [ CLK][nouveau0] 03: core 169 MHz shader 338 MHz memory 100 MHz
drm kern info: nouveau [ CLK][nouveau0] 05: core 275 MHz shader 550 MHz memory 250 MHz
drm kern info: nouveau [ CLK][nouveau0] 07: core 500 MHz shader 1000 MHz memory 400 MHz
drm kern info: nouveau [ CLK][nouveau0] 0f: core 580 MHz shader 1450 MHz memory 400 MHz
drm kern info: nouveau [ CLK][nouveau0] --: core 275 MHz shader 550 MHz memory 249 MHz
Zone kernel: Available graphics memory: 1404372 kiB
drm kern info: nouveau [ DRM] VRAM: 256 MiB
drm kern info: nouveau [ DRM] GART: 1048576 MiB
drm kern info: nouveau [ DRM] TMDS table version 2.0
drm kern info: nouveau [ DRM] DCB version 4.0
drm kern info: nouveau [ DRM] DCB outp 00: 01000323 00010034
drm kern info: nouveau [ DRM] DCB outp 01: 02011300 00000028
drm kern info: nouveau [ DRM] DCB outp 02: 02022386 0f200010
drm kern info: nouveau [ DRM] DCB outp 03: 02022332 00020010
drm kern info: nouveau [ DRM] DCB outp 04: 040333a6 0f200010
drm kern info: nouveau [ DRM] DCB outp 05: 04033312 00020010
drm kern info: nouveau [ DRM] DCB conn 00: 00000041
drm kern info: nouveau [ DRM] DCB conn 01: 00000100
drm kern info: nouveau [ DRM] DCB conn 02: 00005246
drm kern info: nouveau [ DRM] DCB conn 03: 0000a346
drm: Supports vblank timestamp caching Rev 2 (21.10.2013).
drm: Driver supports precise vblank timestamp query.
drm kern info: nouveau [ DRM] MM: using M2MF for buffer copies
nouveaufb0 at nouveau0
nouveau0: info: registered panic notifier
nouveaufb0: framebuffer at 0xffff80004b3e2000, size 1440x900, depth 32, stride 5760
wsdisplay0 at nouveaufb0 kbdmux 1: console (default, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
wm0 at pci0 dev 25 function 0: 82801I mobile (AMT) LAN Controller (rev. 0x03)
wm0: interrupting at ioapic0 pin 22
wm0: PCI-Express bus
wm0: 2048 words FLASH
wm0: Ethernet address 00:26:b9:cd:21:c2
makphy0 at wm0 phy 2: Marvell 88E1149 Gigabit PHY, rev. 1
makphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
uhci0 at pci0 dev 26 function 0: vendor 8086 product 2937 (rev. 0x03)
uhci0: interrupting at ioapic0 pin 20
usb0 at uhci0: USB revision 1.0
uhci1 at pci0 dev 26 function 1: vendor 8086 product 2938 (rev. 0x03)
uhci1: interrupting at ioapic0 pin 21
usb1 at uhci1: USB revision 1.0
uhci2 at pci0 dev 26 function 2: vendor 8086 product 2939 (rev. 0x03)
uhci2: interrupting at ioapic0 pin 22
usb2 at uhci2: USB revision 1.0
ehci0 at pci0 dev 26 function 7: vendor 8086 product 293c (rev. 0x03)
ehci0: interrupting at ioapic0 pin 22
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2
usb3 at ehci0: USB revision 2.0
hdaudio0 at pci0 dev 27 function 0: HD Audio Controller
hdaudio0: interrupting at ioapic0 pin 21
hdafg0 at hdaudio0: vendor 111d product 76b2
hdafg0: DAC00 2ch: Speaker [Built-In], HP Out [Jack]
hdafg0: ADC01 2ch: Mic In [Jack]
hdafg0: DAC02 2ch: Speaker [Jack]
hdafg0: ADC03 2ch: Mic In [Built-In]
hdafg0: DIG04 2ch: SPDIF Out [Jack]
hdafg0: 2ch/2ch 44100Hz 48000Hz 88200Hz 96000Hz 192000Hz PCM16 PCM20 PCM24 AC3
audio0 at hdafg0: full duplex, playback, capture, mmap, independent
ppb1 at pci0 dev 28 function 0: vendor 8086 product 2940 (rev. 0x03)
ppb1: PCI Express capability version 1 <Root Port of PCI-E Root Complex> x1 @ 2.5GT/s
pci2 at ppb1 bus 11
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
ppb2 at pci0 dev 28 function 1: vendor 8086 product 2942 (rev. 0x03)
ppb2: PCI Express capability version 1 <Root Port of PCI-E Root Complex> x1 @ 2.5GT/s
pci3 at ppb2 bus 12
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
iwn0 at pci3 dev 0 function 0: vendor 8086 product 4235 (rev. 0x00)
iwn0: interrupting at ioapic0 pin 17
iwn0: MIMO 3T3R, MoW, address 00:21:6a:ba:79:e2
iwn0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
iwn0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
iwn0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
ppb3 at pci0 dev 28 function 2: vendor 8086 product 2944 (rev. 0x03)
ppb3: PCI Express capability version 1 <Root Port of PCI-E Root Complex> x1 @ 2.5GT/s
pci4 at ppb3 bus 13
pci4: i/o space, memory space enabled, rd/line, wr/inv ok
ppb4 at pci0 dev 28 function 3: vendor 8086 product 2946 (rev. 0x03)
ppb4: PCI Express capability version 1 <Root Port of PCI-E Root Complex> x1 @ 2.5GT/s
pci5 at ppb4 bus 14
pci5: i/o space, memory space enabled, rd/line, wr/inv ok
uhci3 at pci0 dev 29 function 0: vendor 8086 product 2934 (rev. 0x03)
uhci3: interrupting at ioapic0 pin 20
usb4 at uhci3: USB revision 1.0
uhci4 at pci0 dev 29 function 1: vendor 8086 product 2935 (rev. 0x03)
uhci4: interrupting at ioapic0 pin 21
usb5 at uhci4: USB revision 1.0
uhci5 at pci0 dev 29 function 2: vendor 8086 product 2936 (rev. 0x03)
uhci5: interrupting at ioapic0 pin 22
usb6 at uhci5: USB revision 1.0
ehci1 at pci0 dev 29 function 7: vendor 8086 product 293a (rev. 0x03)
ehci1: interrupting at ioapic0 pin 20
ehci1: EHCI version 1.0
ehci1: companion controllers, 2 ports each: uhci3 uhci4 uhci5
usb7 at ehci1: USB revision 2.0
ppb5 at pci0 dev 30 function 0: vendor 8086 product 2448 (rev. 0x93)
pci6 at ppb5 bus 3
pci6: i/o space, memory space enabled
fwohci0 at pci6 dev 1 function 0: vendor 1180 product 0832 (rev. 0x04)
fwohci0: interrupting at ioapic0 pin 17
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 37:4f:c0:00:34:ae:d8:90
fwohci0: Phy 1394a available S400, 1 ports.
fwohci0: Link S400, max_rec 2048 bytes.
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwohci0: Initiate bus reset
sdhc0 at pci6 dev 1 function 1: vendor 1180 product 0822 (rev. 0x21)
sdhc0: interrupting at ioapic0 pin 18
sdhc0: SDHC 1.0, rev 4, SDMA, 33000 kHz, HS 3.3V, 512 byte blocks
sdmmc0 at sdhc0 slot 0
vendor 1180 product 0843 (miscellaneous system, revision 0x11) at pci6 dev 1 function 2 not configured
ichlpcib0 at pci0 dev 31 function 0: vendor 8086 product 2917 (rev. 0x03)
timecounter: Timecounter "ichlpcib0" frequency 3579545 Hz quality 1000
ichlpcib0: 24-bit timer
tco0 at ichlpcib0: TCO (watchdog) timer configured.
tco0: Min/Max interval 1/367 seconds
gpio0 at ichlpcib0: 64 pins
ahcisata0 at pci0 dev 31 function 2: vendor 8086 product 282a (rev. 0x03)
ahcisata0: interrupting at ioapic0 pin 19
ahcisata0: 64-bit DMA
ahcisata0: AHCI revision 1.20, 4 ports, 32 slots, CAP 0xef22ffe3<SXS,EMS,CCCS,PSC,SSC,PMD,SPM,ISS=0x2=Gen2,SCLO,SAL,SALP,SSS,SSNTF,SNCQ,S64A>
atabus0 at ahcisata0 channel 0
atabus1 at ahcisata0 channel 1
atabus2 at ahcisata0 channel 4
atabus3 at ahcisata0 channel 5
ichsmb0 at pci0 dev 31 function 3: vendor 8086 product 2930 (rev. 0x03)
ichsmb0: interrupting at ioapic0 pin 19
iic0 at ichsmb0: I2C bus
isa0 at ichlpcib0
tpm0 at isa0 iomem 0xfed40000-0xfed44fff irq 7: device 0x200114e4 rev 0x30
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
acpicpu0 at cpu0: ACPI CPU
acpicpu0: C1: FFH, lat 1 us, pow 1000 mW
acpicpu0: C2: FFH, lat 1 us, pow 500 mW
acpicpu0: C3: FFH, lat 162 us, pow 100 mW, bus master check
acpicpu0: P0: FFH, lat 10 us, pow 35000 mW, 2801 MHz, turbo boost
acpicpu0: P1: FFH, lat 10 us, pow 35000 mW, 2800 MHz
acpicpu0: P2: FFH, lat 10 us, pow 16607 mW, 2134 MHz
acpicpu0: P3: FFH, lat 10 us, pow 15000 mW, 1600 MHz
acpicpu0: P4: FFH, lat 10 us, pow 12000 mW, 800 MHz
acpicpu0: T0: I/O, lat 1 us, pow 0 mW, 100 %
acpicpu0: T1: I/O, lat 1 us, pow 0 mW, 88 %
acpicpu0: T2: I/O, lat 1 us, pow 0 mW, 76 %
acpicpu0: T3: I/O, lat 1 us, pow 0 mW, 64 %
acpicpu0: T4: I/O, lat 1 us, pow 0 mW, 52 %
acpicpu0: T5: I/O, lat 1 us, pow 0 mW, 40 %
acpicpu0: T6: I/O, lat 1 us, pow 0 mW, 28 %
acpicpu0: T7: I/O, lat 1 us, pow 0 mW, 16 %
coretemp0 at cpu0: thermal sensor, 1 C resolution, Tjmax=100
acpicpu1 at cpu1: ACPI CPU
coretemp1 at cpu1: thermal sensor, 1 C resolution, Tjmax=100
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
ieee1394if0: 1 nodes, maxhop <= 0 cable IRM irm(0) (me)
ieee1394if0: bus manager 0
drm kern error: nouveau E[ PDISP][nouveau0] INVALID_STATE [UNK0B] chid 1 mthd 0x0080 data 0x00000000
drm kern error: nouveau E[ PDISP][nouveau0] Base 0:
drm kern error: nouveau E[ PDISP][nouveau0] 0x0084: 0x00000000
drm kern error: nouveau E[ PDISP][nouveau0] 0x0088: 0x00000000
drm kern error: nouveau E[ PDISP][nouveau0] 0x008c: 0x00000000
drm kern error: nouveau E[ PDISP][nouveau0] 0x0090: 0x00000000
drm kern error: nouveau E[ PDISP][nouveau0] 0x0094: 0x00000000 -> 0xcafe0000
drm kern error: nouveau E[ PDISP][nouveau0] 0x00a0: 0x00000000
drm kern error: nouveau E[ PDISP][nouveau0] 0x00a4: 0x00000000
drm kern error: nouveau E[ PDISP][nouveau0] 0x00c0: 0x00000000 -> 0x01000003
drm kern error: nouveau E[ PDISP][nouveau0] 0x00c4: 0x00000000
drm kern error: nouveau E[ PDISP][nouveau0] 0x00c8: 0x00000000
drm kern error: nouveau E[ PDISP][nouveau0] 0x00cc: 0x00000000
drm kern error: nouveau E[ PDISP][nouveau0] 0x00e0: 0x00000000 -> 0x40000000
drm kern error: nouveau E[ PDISP][nouveau0] 0x00e4: 0x00000000
drm kern error: nouveau E[ PDISP][nouveau0] 0x00e8: 0x00000000
drm kern error: nouveau E[ PDISP][nouveau0] 0x00ec: 0x00000000
drm kern error: nouveau E[ PDISP][nouveau0] 0x00fc: 0x00000000
drm kern error: nouveau E[ PDISP][nouveau0] 0x0100: 0xfffe0000
drm kern error: nouveau E[ PDISP][nouveau0] 0x0104: 0x00000000
drm kern error: nouveau E[ PDISP][nouveau0] 0x0110: 0x00000000
drm kern error: nouveau E[ PDISP][nouveau0] 0x0114: 0x00000000
drm kern error: nouveau E[ PDISP][nouveau0] Base 0 - Image 0:
drm kern error: nouveau E[ PDISP][nouveau0] 0x0800: 0x00000000 -> 0x00000600
drm kern error: nouveau E[ PDISP][nouveau0] 0x0804: 0x00000000
drm kern error: nouveau E[ PDISP][nouveau0] 0x0808: 0x00000000 -> 0x038405a0
drm kern error: nouveau E[ PDISP][nouveau0] 0x080c: 0x00000000 -> 0x00101700
drm kern error: nouveau E[ PDISP][nouveau0] 0x0810: 0x0000e900 -> 0x0000cf00
drm kern error: nouveau E[ PDISP][nouveau0] Base 0 - Image 1:
drm kern error: nouveau E[ PDISP][nouveau0] 0x0c00: 0x00000000 -> 0x00000600
drm kern error: nouveau E[ PDISP][nouveau0] 0x0c04: 0x00000000
drm kern error: nouveau E[ PDISP][nouveau0] 0x0c08: 0x00000000 -> 0x038405a0
drm kern error: nouveau E[ PDISP][nouveau0] 0x0c0c: 0x00000000 -> 0x00101700
drm kern error: nouveau E[ PDISP][nouveau0] 0x0c10: 0x0000e900 -> 0x0000cf00
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
acpiacad0: AC adapter online.
IPsec: Initialized Security Association Processing.
uhub0 at usb0: vendor 8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: vendor 8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: vendor 8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhub3 at usb3: vendor 8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 6 ports with 6 removable, self powered
uhub4 at usb4: vendor 8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub4: 2 ports with 2 removable, self powered
uhub5 at usb5: vendor 8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub5: 2 ports with 2 removable, self powered
uhub6 at usb6: vendor 8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub6: 2 ports with 2 removable, self powered
uhub7 at usb7: vendor 8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub7: 6 ports with 6 removable, self powered
ahcisata0 port 0: device present, speed: 3.0Gb/s
ahcisata0 port 1: device present, speed: 1.5Gb/s
ehci0: handing over full speed device on port 5 to uhci2
wd0 at atabus0 drive 0
wd0: <ST9250410ASG>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 232 GB, 484521 cyl, 16 head, 63 sec, 512 bytes/sect x 488397168 sectors
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(ahcisata0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) (using DMA)
atapibus0 at atabus1: 1 targets
cd0 at atapibus0 drive 0: <PLDS DVD+/-RW DU-8A3S, 911100494545, KD01> cdrom removable
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
cd0(ahcisata0:1:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100) (using DMA)
uvideo0 at uhub3 port 6 configuration 1 interface 0: M092S-R00-0324-SC29X Integrated_Webcam_2M, rev 2.00/94.10, addr 2
video0 at uvideo0: M092S-R00-0324-SC29X Integrated_Webcam_2M, rev 2.00/94.10, addr 2
pad0: outputs: 44100Hz, 16-bit, stereo
audio1 at pad0: half duplex, playback, capture
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
kern.module.path=/stand/amd64/7.99.32/modules
ugen0 at uhub2 port 1
ugen0: Broadcom Corp 5880, rev 1.10/1.01, addr 2
acpibat0: normal capacity on 'charge state'
iwn0: radio is disabled by hardware switch
iwn0: cannot assign link-local address
iwn0: radio is disabled by hardware switch
iwn0: radio is disabled by hardware switch
iwn0: cannot assign link-local address
wsdisplay0: screen 1 added (default, vt100 emulation)
wsdisplay0: screen 2 added (default, vt100 emulation)
wsdisplay0: screen 3 added (default, vt100 emulation)
wsdisplay0: screen 4 added (default, vt100 emulation)
-tih
--
Elections cannot be allowed to change anything. --Dr. Wolfgang Schäuble
Home |
Main Index |
Thread Index |
Old Index