Bananapi - looping on boot

[Frank Kardel <kardel%netbsd.org@localhost>]

Hi !

I just try out -current (20141229 evbarm/earmv7hf) and see the boot 
constantly looping like this:

U-Boot SPL 2014.04-10733-gea1ac32 (Nov 24 2014 - 09:46:23)
Board: Bananapi
DRAM: 1024 MiB
CPU: 960000000Hz, AXI/AHB/APB: 3/2/2
spl: not an uImage at 1600


U-Boot 2014.04-10733-gea1ac32 (Nov 24 2014 - 09:46:23) Allwinner Technology

CPU:   Allwinner A20 (SUN7I)
Board: Bananapi
I2C:   ready
DRAM:  1 GiB
MMC:   SUNXI SD/MMC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   dwmac.1c50000
Hit any key to stop autoboot:  0
reading uEnv.txt
140 bytes read in 21 ms (5.9 KiB/s)
Loaded environment from uEnv.txt
Running uenvcmd ...
mmc0 is current device
reading Bananapi.bin
50908 bytes read in 31 ms (1.6 MiB/s)
reading netbsd.ub
5136896 bytes read in 310 ms (15.8 MiB/s)
## Booting kernel from Legacy Image at 82000000 ...
   Image Name:   NetBSD/bpi 7.99.3
   Image Type:   ARM NetBSD Kernel Image (uncompressed)
   Data Size:    5136832 Bytes = 4.9 MiB
   Load Address: 40007800
   Entry Point:  40007800
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
## Transferring control to NetBSD stage-2 loader (at address 40007800) ...
Early console started
[ Kernel symbol table missing! ]
    The Regents of the University of California.  All rights reserved.

NetBSD 7.99.3 (BPI) #1: Tue Dec 30 10:10:55 CET 2014

kardel@Andromeda:/usr/srccur/src/sys/arch/evbarm/compile/obj.evbarm/BPI
total memory = 1024 MB
avail memory = 1008 MB
sysctl_createv: sysctl_create(machine_arch) returned 17
mainbus0 (root)
cpu0 at mainbus0 core 0: 960 MHz Cortex-A7 r0p4 (Cortex V7A core)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB/32B 2-way L1 VIPT Instruction cache
cpu0: 32KB/64B 4-way write-back-locking-C L1 PIPT Data cache
cpu0: 256KB/64B 8-way write-through L2 PIPT Unified cache
vfp0 at cpu0: NEON MPE (VFP 3.0+), rounding, NaN propagation, denormals
cpu1 at mainbus0 core 1
armperiph0 at mainbus0
armgic0 at armperiph0: Generic Interrupt Controller, 160 sources (151 valid)
armgic0: 32 Priorities, 128 SPIs, 7 PPIs, 16 SGIs
armgtmr0 at armperiph0: ARMv7 Generic 64-bit Timer (24000 kHz)
armgtmr0: interrupting on irq 27
awinio0 at mainbus0: A20 (0x1651)
awingpio0 at awinio0
awindma0 at awinio0: DMA
awindma0: interrupting on irq 59
awincnt0 at awinio0
com0 at awinio0 port 0: ns16550a, working fifo
com0: console
awindebe0 at awinio0 port 0: Display Engine Backend (BE0)
awintcon0 at awinio0 port 0: LCD/TV timing controller (TCON0)
awinhdmi0 at awinio0: HDMI 1.3
awinwdt0 at awinio0: default period is 10 seconds
awinrtc0 at awinio0: RTC
awinusb0 at awinio0 port 0
ohci0 at awinusb0: OHCI USB controller
ohci0: OHCI version 1.0
usb0 at ohci0: USB revision 1.0
ohci0: interrupting on irq 96
ehci0 at awinusb0: EHCI USB controller
ehci0: companion controller, 1 port each: ohci0
usb1 at ehci0: USB revision 2.0
ehci0: interrupting on irq 71
awinusb1 at awinio0 port 1
ohci1 at awinusb1: OHCI USB controller
ohci1: OHCI version 1.0
usb2 at ohci1: USB revision 1.0
ohci1: interrupting on irq 97
ehci1 at awinusb1: EHCI USB controller
ehci1: companion controller, 1 port each: ohci1
usb3 at ehci1: USB revision 2.0
ehci1: interrupting on irq 72
motg0 at awinio0: OTG
motg0: interrupting at irq 70

U-Boot SPL 2014.04-10733-gea1ac32 (Nov 24 2014 - 09:46:23)
Board: Bananapi
DRAM: 1024 MiB
CPU: 960000000Hz, AXI/AHB/APB: 3/2/2
spl: not an uImage at 1600


U-Boot 2014.04-10733-gea1ac32 (Nov 24 2014 - 09:46:23) Allwinner Technology

CPU:   Allwinner A20 (SUN7I)
Board: Bananapi
I2C:   ready
DRAM:  1 GiB
MMC:   SUNXI SD/MMC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   dwmac.1c50000
Hit any key to stop autoboot:  0
sun7i#

Any ideas? I was following the instruction from 
http://wiki.netbsd.org/ports/evbarm/allwinner/.

Frank