Re: Can't boot -curent in qemu

To: Christoph Egger <Christoph_Egger%gmx.de@localhost>
Subject: Re: Can't boot -curent in qemu
From: Paul Goyette <paul%whooppee.com@localhost>
Date: Sat, 14 Apr 2012 11:04:55 -0700 (PDT)

On Sat, 14 Apr 2012, Christoph Egger wrote:

Just as a side note, I noticed that there is no amdtemp sensor found on
my Bulldozer FX-8150 (M5A99X-EVO motherboard).


Here comes up the question, does it not attach due to an CPU errata or
due to the revert ?

One amdnb_miscX should attach on each northbridge function 3 device.
One amdtempX should attach on amdnb_miscX.
Can you see that in dmesg?

I have attached my dmesg from 6.99.2 as well as output from lspci. Isee only two devices with a function 3


# lspci | grep '\.3'
00:14.3 ISA bridge: ATI Technologies Inc SB700/SB800 LPC host controller (rev 
40)
00:18.3 Host bridge: Advanced Micro Devices [AMD] Device 1603
#



-------------------------------------------------------------------------
| Paul Goyette     | PGP Key fingerprint:     | E-mail addresses:       |
| Customer Service | FA29 0E3B 35AF E8AE 6651 | paul at whooppee.com    |
| Network Engineer | 0786 F758 55DE 53BA 7731 | pgoyette at juniper.net |
| Kernel Developer |                          | pgoyette at netbsd.org  |
-------------------------------------------------------------------------

00:00.0 Host bridge: ATI Technologies Inc RD890 PCI to PCI bridge (external 
gfx0 port B) (rev 02)
00:02.0 PCI bridge: ATI Technologies Inc RD890 PCI to PCI bridge (PCI express 
gpp port B)
00:04.0 PCI bridge: ATI Technologies Inc RD890 PCI to PCI bridge (PCI express 
gpp port D)
00:05.0 PCI bridge: ATI Technologies Inc RD890 PCI to PCI bridge (PCI express 
gpp port E)
00:06.0 PCI bridge: ATI Technologies Inc RD890 PCI to PCI bridge (PCI express 
gpp port F)
00:07.0 PCI bridge: ATI Technologies Inc RD890 PCI to PCI bridge (PCI express 
gpp port G)
00:0a.0 PCI bridge: ATI Technologies Inc RD890 PCI to PCI bridge (external gfx1 
port A)
00:11.0 SATA controller: ATI Technologies Inc SB700/SB800 SATA Controller [AHCI 
mode] (rev 40)
00:12.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller
00:12.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller
00:13.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller
00:13.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller
00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 42)
00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) (rev 40)
00:14.3 ISA bridge: ATI Technologies Inc SB700/SB800 LPC host controller (rev 
40)
00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge (rev 40)
00:14.5 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI2 Controller
00:16.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller
00:16.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller
00:18.0 Host bridge: Advanced Micro Devices [AMD] Device 1600
00:18.1 Host bridge: Advanced Micro Devices [AMD] Device 1601
00:18.2 Host bridge: Advanced Micro Devices [AMD] Device 1602
00:18.3 Host bridge: Advanced Micro Devices [AMD] Device 1603
00:18.4 Host bridge: Advanced Micro Devices [AMD] Device 1604
00:18.5 Host bridge: Advanced Micro Devices [AMD] Device 1605
01:00.0 VGA compatible controller: ATI Technologies Inc RV710 [Radeon HD 4350]
01:00.1 Audio device: ATI Technologies Inc R700 Audio Device [Radeon HD 4000 
Series]
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI 
Express Gigabit Ethernet controller (rev 06)
03:00.0 USB Controller: Device 1b21:1042
04:00.0 IDE interface: JMicron Technology Corp. Device 2362 (rev 10)
05:00.0 USB Controller: Device 1b21:1042
06:00.0 IDE interface: JMicron Technology Corp. Device 2362 (rev 10)
07:06.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6306 Fire II IEEE 1394 
OHCI Link Layer Controller (rev c0)

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010, 2011, 2012
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 6.99.2 (WHOOPPEE (shared) 2012-02-19 03:27:19) #0: Thu Mar 15 10:16:30 
PDT 2012
        
paul%screamer.whooppee.com@localhost:/build/netbsd-old/obj/amd64/sys/arch/amd64/compile/WHOOPPEE
total memory = 16329 MB
avail memory = 15849 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
To be filled by O.E.M. To be filled by O.E.M. (To be filled by O.E.M.)
mainbus0 (root)
ACPI Warning: Optional field Pm2ControlBlock has zero address or length: 
0x0000000000000000/0x1 (20110623/tbfadt-586)
cpu0 at mainbus0 apid 16: AMD FX(tm)-8150 Eight-Core Processor           , id 
0x600f12
cpu0: SVM disabled by the BIOS
cpu1 at mainbus0 apid 17: AMD FX(tm)-8150 Eight-Core Processor           , id 
0x600f12
cpu2 at mainbus0 apid 18: AMD FX(tm)-8150 Eight-Core Processor           , id 
0x600f12
cpu3 at mainbus0 apid 19: AMD FX(tm)-8150 Eight-Core Processor           , id 
0x600f12
cpu4 at mainbus0 apid 20: AMD FX(tm)-8150 Eight-Core Processor           , id 
0x600f12
cpu5 at mainbus0 apid 21: AMD FX(tm)-8150 Eight-Core Processor           , id 
0x600f12
cpu6 at mainbus0 apid 22: AMD FX(tm)-8150 Eight-Core Processor           , id 
0x600f12
cpu7 at mainbus0 apid 23: AMD FX(tm)-8150 Eight-Core Processor           , id 
0x600f12
ioapic0 at mainbus0 apid 9: pa 0xfec00000, version 21, 24 pins
ioapic1 at mainbus0 apid 10: pa 0xfec20000, version 21, 32 pins
acpi0 at mainbus0: Intel ACPICA 20110623
acpi0: X/RSDT: OemId <ALASKA,   A M I,01072009>, AslId <AMI ,00010013>
ACPI Error: [RAMB] Namespace lookup failure, AE_NOT_FOUND (20110623/psargs-392)
ACPI Exception: AE_NOT_FOUND, Could not execute arguments for [RAMW] (Region) 
(20110623/nsinit-380)
acpi0: SCI interrupting at int 9
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
acpiec0 at acpi0 (EC0, PNP0C09): io 0x62,0x66
AMDN (PNP0C01) at acpi0 not configured
S800 (PNP0C02) at acpi0 not configured
SIO1 (PNP0C02) at acpi0 not configured
attimer0 at acpi0 (TMR, PNP0100): io 0x40-0x43 irq 0
pcppi0 at acpi0 (SPKR, PNP0800): io 0x61
midi0 at pcppi0: PC speaker
sysbeep0 at pcppi0
RMSC (PNP0C02) at acpi0 not configured
NBRM (PNP0C02) at acpi0 not configured
com0 at acpi0 (UAR1, PNP0501-1): io 0x3f8-0x3ff irq 4
com0: ns16550a, working fifo
WMI1 (PNP0C14) at acpi0 not configured
UMEM (PNP0C02) at acpi0 not configured
NMEM (PNP0C02) at acpi0 not configured
PWRB (PNP0C0C) at acpi0 not configured
RMEM (PNP0C01) at acpi0 not configured
HPET (PNP0103) at acpi0 not configured
OMSC (PNP0C02) at acpi0 not configured
AMW0 (PNP0C14) at acpi0 not configured
attimer0: attached to pcppi0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0: vendor 0x1002 product 0x5a14 (rev. 0x02)
ppb0 at pci0 dev 2 function 0: vendor 0x1002 product 0x5a16 (rev. 0x00)
ppb0: PCI Express 2.0 <Root Port of PCI-E Root Complex>
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
vga0 at pci1 dev 0 function 0: vendor 0x1002 product 0x954f (rev. 0x00)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
radeondrm0 at vga0: ATI Radeon HD 4350
radeondrm0: Initialized radeon 1.29.0 20080613
vendor 0x1002 product 0xaa38 (multimedia, subclass 0x03) at pci1 dev 0 function 
1 not configured
ppb1 at pci0 dev 4 function 0: vendor 0x1002 product 0x5a18 (rev. 0x00)
ppb1: PCI Express 2.0 <Root Port of PCI-E Root Complex>
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
re0 at pci2 dev 0 function 0: RealTek 8168/8111 PCIe Gigabit Ethernet (rev. 
0x06)
re0: interrupting at ioapic1 pin 20
re0: Unknown revision (0x2c800000)
re0: Ethernet address c8:60:00:02:30:47
re0: using 256 tx descriptors
rgephy0 at re0 phy 7: RTL8169S/8110S/8211 1000BASE-T media interface, rev. 5
rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
ppb2 at pci0 dev 5 function 0: vendor 0x1002 product 0x5a19 (rev. 0x00)
ppb2: PCI Express 2.0 <Root Port of PCI-E Root Complex>
pci3 at ppb2 bus 3
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
vendor 0x1b21 product 0x1042 (USB serial bus, interface 0x30) at pci3 dev 0 
function 0 not configured
ppb3 at pci0 dev 6 function 0: vendor 0x1002 product 0x5a1a (rev. 0x00)
ppb3: PCI Express 2.0 <Root Port of PCI-E Root Complex>
pci4 at ppb3 bus 4
pci4: i/o space, memory space enabled, rd/line, wr/inv ok
vendor 0x197b product 0x2362 (IDE mass storage, interface 0x85, revision 0x10) 
at pci4 dev 0 function 0 not configured
ppb4 at pci0 dev 7 function 0: vendor 0x1002 product 0x5a1b (rev. 0x00)
ppb4: PCI Express 2.0 <Root Port of PCI-E Root Complex>
pci5 at ppb4 bus 5
pci5: i/o space, memory space enabled, rd/line, wr/inv ok
vendor 0x1b21 product 0x1042 (USB serial bus, interface 0x30) at pci5 dev 0 
function 0 not configured
ppb5 at pci0 dev 10 function 0: vendor 0x1002 product 0x5a1d (rev. 0x00)
ppb5: PCI Express 2.0 <Root Port of PCI-E Root Complex>
pci6 at ppb5 bus 6
pci6: i/o space, memory space enabled, rd/line, wr/inv ok
vendor 0x197b product 0x2362 (IDE mass storage, interface 0x85, revision 0x10) 
at pci6 dev 0 function 0 not configured
ahcisata0 at pci0 dev 17 function 0: vendor 0x1002 product 0x4391 (rev. 0x40)
ahcisata0: interrupting at ioapic0 pin 19
ahcisata0: 64-bit DMA
ahcisata0: AHCI revision 1.20, 6 ports, 32 slots, CAP 
0xf732ff05<PSC,SSC,PMD,SPM,ISS=0x3=Gen3,SCLO,SAL,SALP,SMPS,SSNTF,SNCQ,S64A>
atabus0 at ahcisata0 channel 0
atabus1 at ahcisata0 channel 1
atabus2 at ahcisata0 channel 2
atabus3 at ahcisata0 channel 3
atabus4 at ahcisata0 channel 4
atabus5 at ahcisata0 channel 5
ohci0 at pci0 dev 18 function 0: vendor 0x1002 product 0x4397 (rev. 0x00)
ohci0: interrupting at ioapic0 pin 18
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
ehci0 at pci0 dev 18 function 2: vendor 0x1002 product 0x4396 (rev. 0x00)
ehci0: interrupting at ioapic0 pin 17
ehci0: dropped intr workaround enabled
ehci0: BIOS has given up ownership
ehci0: EHCI version 1.0
ehci0: companion controller, 5 ports each: ohci0
usb1 at ehci0: USB revision 2.0
ohci1 at pci0 dev 19 function 0: vendor 0x1002 product 0x4397 (rev. 0x00)
ohci1: interrupting at ioapic0 pin 20
ohci1: OHCI version 1.0, legacy support
usb2 at ohci1: USB revision 1.0
ehci1 at pci0 dev 19 function 2: vendor 0x1002 product 0x4396 (rev. 0x00)
ehci1: interrupting at ioapic0 pin 21
ehci1: dropped intr workaround enabled
ehci1: BIOS has given up ownership
ehci1: EHCI version 1.0
ehci1: companion controller, 5 ports each: ohci1
usb3 at ehci1: USB revision 2.0
piixpm0 at pci0 dev 20 function 0: vendor 0x1002 product 0x4385 (rev. 0x42)
piixpm0: polling (SB800)
iic0 at piixpm0: I2C bus
vendor 0x1002 product 0x4383 (multimedia, subclass 0x03, revision 0x40) at pci0 
dev 20 function 2 not configured
pcib0 at pci0 dev 20 function 3: vendor 0x1002 product 0x439d (rev. 0x40)
ppb6 at pci0 dev 20 function 4: vendor 0x1002 product 0x4384 (rev. 0x40)
pci7 at ppb6 bus 7
pci7: i/o space, memory space enabled
fwohci0 at pci7 dev 6 function 0: vendor 0x1106 product 0x3044 (rev. 0xc0)
fwohci0: interrupting at ioapic0 pin 21
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:1f:c6:00:00:1b:51:af
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwohci0: Initiate bus reset
ohci2 at pci0 dev 20 function 5: vendor 0x1002 product 0x4399 (rev. 0x00)
ohci2: interrupting at ioapic0 pin 18
ohci2: OHCI version 1.0, legacy support
usb4 at ohci2: USB revision 1.0
ohci3 at pci0 dev 22 function 0: vendor 0x1002 product 0x4397 (rev. 0x00)
ohci3: interrupting at ioapic0 pin 22
ohci3: OHCI version 1.0, legacy support
usb5 at ohci3: USB revision 1.0
ehci2 at pci0 dev 22 function 2: vendor 0x1002 product 0x4396 (rev. 0x00)
ehci2: interrupting at ioapic0 pin 23
ehci2: dropped intr workaround enabled
ehci2: BIOS has given up ownership
ehci2: EHCI version 1.0
ehci2: companion controller, 4 ports each: ohci3
usb6 at ehci2: USB revision 2.0
pchb1 at pci0 dev 24 function 0: vendor 0x1022 product 0x1600 (rev. 0x00)
pchb2 at pci0 dev 24 function 1: vendor 0x1022 product 0x1601 (rev. 0x00)
pchb3 at pci0 dev 24 function 2: vendor 0x1022 product 0x1602 (rev. 0x00)
pchb4 at pci0 dev 24 function 3: vendor 0x1022 product 0x1603 (rev. 0x00)
pchb5 at pci0 dev 24 function 4: vendor 0x1022 product 0x1604 (rev. 0x00)
pchb6 at pci0 dev 24 function 5: vendor 0x1022 product 0x1605 (rev. 0x00)
isa0 at pcib0
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
ieee1394if0: 1 nodes, maxhop <= 0 cable IRM irm(0) (me)
ieee1394if0: bus manager 0
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
ERROR: 4172 cycle TSC drift observed
uhub0 at usb6: vendor 0x1002 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub0: 4 ports with 4 removable, self powered
uhub1 at usb5: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 4 ports with 4 removable, self powered
uhub2 at usb4: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhub3 at usb3: vendor 0x1002 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 5 ports with 5 removable, self powered
uhub4 at usb2: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub4: 5 ports with 5 removable, self powered
ahcisata0 port 0: device present, speed: 3.0Gb/s
uhub5 at usb1: vendor 0x1002 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub5: 5 ports with 5 removable, self powered
uhub6 at usb0: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub6: 5 ports with 5 removable, self powered
wd0 at atabus0 drive 0
wd0: <Maxtor 7H500F0>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 465 GB, 969021 cyl, 16 head, 63 sec, 512 bytes/sect x 976773168 sectors
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(ahcisata0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) 
(using DMA)
swwdog0: software watchdog initialized
Kernelized RAIDframe activated
boot device: wd0
root on wd0a dumps on wd0b
uhidev0 at uhub4 port 2 configuration 1 interface 0
uhidev0: Justcom Technology USB KVM Switch, rev 1.10/1.00, addr 2, iclass 3/1
ukbd0 at uhidev0
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev1 at uhub4 port 2 configuration 1 interface 1
uhidev1: Justcom Technology USB KVM Switch, rev 1.10/1.00, addr 2, iclass 3/1
ums0 at uhidev1: 5 buttons and Z dir
wsmouse0 at ums0 mux 0
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
Accounting started
AMDN (PNP0C01) [System Board] at acpi0 not configured
S800 (PNP0C02) [Motherboard Register Resources] at acpi0 not configured
SIO1 (PNP0C02) [Motherboard Register Resources] at acpi0 not configured
RMSC (PNP0C02) [Motherboard Register Resources] at acpi0 not configured
NBRM (PNP0C02) [Motherboard Register Resources] at acpi0 not configured
WMI1 (PNP0C14) [WMI Mapper Device] at acpi0 not configured
UMEM (PNP0C02) [Motherboard Register Resources] at acpi0 not configured
NMEM (PNP0C02) [Motherboard Register Resources] at acpi0 not configured
acpibut0 at acpi0 (PWRB, PNP0C0C-170): ACPI Power Button
RMEM (PNP0C01) [System Board] at acpi0 not configured
HPET (PNP0103) [HPET Timer] at acpi0 not configured
OMSC (PNP0C02) [Motherboard Register Resources] at acpi0 not configured
AMW0 (PNP0C14) [WMI Mapper Device] at acpi0 not configured
acpicpu0 at cpu0: ACPI CPU
acpicpu0: C1: HLT, lat   0 us, pow     0 mW
acpicpu0: C2: I/O, lat 100 us, pow     0 mW, bus master check
acpicpu0: P0: FFH, lat   4 us, pow 15487 mW, 3600 MHz
acpicpu0: P1: FFH, lat   4 us, pow 13117 mW, 3300 MHz
acpicpu0: P2: FFH, lat   4 us, pow  9130 mW, 2700 MHz
acpicpu0: P3: FFH, lat   4 us, pow  6337 mW, 2100 MHz
acpicpu0: P4: FFH, lat   4 us, pow  3937 mW, 1400 MHz
acpicpu0: T0: I/O, lat   1 us, pow     0 mW, 100 %
acpicpu0: T1: I/O, lat   1 us, pow     0 mW,  88 %
acpicpu0: T2: I/O, lat   1 us, pow     0 mW,  76 %
acpicpu0: T3: I/O, lat   1 us, pow     0 mW,  64 %
acpicpu0: T4: I/O, lat   1 us, pow     0 mW,  52 %
acpicpu0: T5: I/O, lat   1 us, pow     0 mW,  40 %
acpicpu0: T6: I/O, lat   1 us, pow     0 mW,  28 %
acpicpu0: T7: I/O, lat   1 us, pow     0 mW,  16 %
acpicpu1 at cpu1: ACPI CPU
acpicpu2 at cpu2: ACPI CPU
acpicpu3 at cpu3: ACPI CPU
acpicpu4 at cpu4: ACPI CPU
acpicpu5 at cpu5: ACPI CPU
acpicpu6 at cpu6: ACPI CPU
acpicpu7 at cpu7: ACPI CPU
AMDN (PNP0C01) [System Board] at acpi0 not configured
S800 (PNP0C02) [Motherboard Register Resources] at acpi0 not configured
SIO1 (PNP0C02) [Motherboard Register Resources] at acpi0 not configured
RMSC (PNP0C02) [Motherboard Register Resources] at acpi0 not configured
NBRM (PNP0C02) [Motherboard Register Resources] at acpi0 not configured
WMI1 (PNP0C14) [WMI Mapper Device] at acpi0 not configured
UMEM (PNP0C02) [Motherboard Register Resources] at acpi0 not configured
NMEM (PNP0C02) [Motherboard Register Resources] at acpi0 not configured
RMEM (PNP0C01) [System Board] at acpi0 not configured
HPET (PNP0103) [HPET Timer] at acpi0 not configured
OMSC (PNP0C02) [Motherboard Register Resources] at acpi0 not configured
AMW0 (PNP0C14) [WMI Mapper Device] at acpi0 not configured
hdaudio0 at pci0 dev 20 function 2: HD Audio Controller
hdaudio0: interrupting at ioapic0 pin 16
hdafg at hdaudio0 not configured
hdaudio1 at pci1 dev 0 function 1: HD Audio Controller
hdaudio1: interrupting at ioapic1 pin 1
hdafg at hdaudio1 not configured
vendor 0x1b21 product 0x1042 (USB serial bus, interface 0x30) at pci3 dev 0 
function 0 not configured
JMicron Technology product 0x2362 (IDE mass storage, interface 0x85, revision 
0x10) at pci4 dev 0 function 0 not configured
unmatched vendor 0x1b21 product 0x1042 (USB serial bus, interface 0x30) at pci5 
dev 0 function 0 not configured
JMicron Technology product 0x2362 (IDE mass storage, interface 0x85, revision 
0x10) at pci6 dev 0 function 0 not configured
hdafg0 at hdaudio0: Realtek ALC892
hdafg0: DAC00 8ch: Speaker [Jack]
hdafg0: DAC01 2ch: HP Out [Jack]
hdafg0: DIG02 2ch: SPDIF Out [Jack]
hdafg0: DIG03 2ch: SPDIF Out [Built-In]
hdafg0: ADC04 2ch: Line In [Jack], Mic In [Jack]
hdafg0: ADC05 2ch: Mic In [Jack]
hdafg0: 8ch/2ch 32000Hz 44100Hz 48000Hz 88200Hz 96000Hz 192000Hz PCM16 PCM20 
PCM24 AC3
audio0 at hdafg0: full duplex, playback, capture, independent
hdafg1 at hdaudio1: ATI R6xx HDMI
hdafg1: HDMI00 2ch: Digital Out [Jack]
hdafg1: 2ch/0ch 32000Hz 44100Hz 48000Hz PCM16 AC3
hpet0 at acpi0: high precision event timer (mem 0xfed00000-0xfed00400)
timecounter: Timecounter "hpet0" frequency 14318180 Hz quality 2000
AMDN (PNP0C01) [System Board] at acpi0 not configured
S800 (PNP0C02) [Motherboard Register Resources] at acpi0 not configured
SIO1 (PNP0C02) [Motherboard Register Resources] at acpi0 not configured
RMSC (PNP0C02) [Motherboard Register Resources] at acpi0 not configured
NBRM (PNP0C02) [Motherboard Register Resources] at acpi0 not configured
WMI1 (PNP0C14) [WMI Mapper Device] at acpi0 not configured
UMEM (PNP0C02) [Motherboard Register Resources] at acpi0 not configured
NMEM (PNP0C02) [Motherboard Register Resources] at acpi0 not configured
RMEM (PNP0C01) [System Board] at acpi0 not configured
OMSC (PNP0C02) [Motherboard Register Resources] at acpi0 not configured
AMW0 (PNP0C14) [WMI Mapper Device] at acpi0 not configured
itesio0 at isa0 port 0x2e-0x2f: iTE IT8721F Super I/O (rev 1)
itesio0: Hardware Monitor registers at 0x290
itesio0: Watchdog Timer present
spdmem0 at iic0 addr 0x50
spdmem0: DDR3 SDRAM, no ECC, no temp-sensor, 4GB, 1333MHz (PC3-10666)
spdmem0: 12 rows, 13 cols, 8 log. banks, 2 phys. banks, 1.500ns cycle time
spdmem0: tAA-tRCD-tRP-tRAS: 9-9-9-24
spdmem1 at iic0 addr 0x51
spdmem1: DDR3 SDRAM, no ECC, no temp-sensor, 4GB, 1333MHz (PC3-10666)
spdmem1: 12 rows, 13 cols, 8 log. banks, 2 phys. banks, 1.500ns cycle time
spdmem1: tAA-tRCD-tRP-tRAS: 9-9-9-24
spdmem2 at iic0 addr 0x52
spdmem2: DDR3 SDRAM, no ECC, no temp-sensor, 4GB, 1333MHz (PC3-10666)
spdmem2: 12 rows, 13 cols, 8 log. banks, 2 phys. banks, 1.500ns cycle time
spdmem2: tAA-tRCD-tRP-tRAS: 9-9-9-24
spdmem3 at iic0 addr 0x53
spdmem3: DDR3 SDRAM, no ECC, no temp-sensor, 4GB, 1333MHz (PC3-10666)
spdmem3: 12 rows, 13 cols, 8 log. banks, 2 phys. banks, 1.500ns cycle time
spdmem3: tAA-tRCD-tRP-tRAS: 9-9-9-24
info: [drm] Setting GART location based on new memory map
info: [drm] Loading RV710 Microcode
info: [drm] Resetting GPU
info: [drm] writeback test succeeded in 1 usecs
radeondrm0: interrupting at ioapic1 pin 0
info: [drm] Resetting GPU
info: [drm] Loading RV710 Microcode
info: [drm] Resetting GPU

Follow-Ups:
- Re: Can't boot -curent in qemu
  - From: Christoph Egger

References:
- Can't boot -curent in qemu
  - From: Paul Goyette
- Re: Can't boot -curent in qemu
  - From: Christoph Egger
- Re: Can't boot -curent in qemu
  - From: Christoph Egger
- Re: Can't boot -curent in qemu
  - From: Paul Goyette
- Re: Can't boot -curent in qemu
  - From: Paul Goyette
- Re: Can't boot -curent in qemu
  - From: Christoph Egger

Prev by Date: Re: Can't boot -curent in qemu
Next by Date: Re: Can't boot -curent in qemu
Previous by Thread: Re: Can't boot -curent in qemu
Next by Thread: Re: Can't boot -curent in qemu
Indexes:

Home | Main Index | Thread Index | Old Index