tech-net archive

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index][Old Index]

Re: bnx(4) lockups?



On 2019/03/25 20:48, Stephen Borrill wrote:
On Sat, 23 Mar 2019, Masanobu SAITOH wrote:
  From my experience in bge(4), I suspect the bnx(4)'s hard hang might
come from access conflict between the driver(CPU) and the embedded
controller.

One question.

bnx0 at pci1 dev 0 function 0: Broadcom NetXtreme II BCM5709 1000Base-T
bnx0: Ethernet address 5c:f3:fc:e4:e6:78
bnx0: interrupting at ioapic1 pin 4
bnx0: ASIC BCM5709 C0 (0x57092003)
bnx0: PCIe x2 5Gbps
bnx0: Coal (RX:6,6,18,18; TX:20,20,80,80)
bnx1 at pci1 dev 0 function 1: Broadcom NetXtreme II BCM5709 1000Base-T
bnx1: Ethernet address 5c:f3:fc:e4:e6:7a
bnx1: interrupting at ioapic1 pin 16
bnx1: ASIC BCM5709 C0 (0x57092003)
bnx1: PCIe x2 5Gbps
bnx1: Coal (RX:6,6,18,18; TX:20,20,80,80)
bnx2 at pci2 dev 0 function 0: Broadcom NetXtreme II BCM5709 1000Base-T
bnx2: Ethernet address 5c:f3:fc:6b:c6:b4
bnx2: interrupting at ioapic1 pin 5
bnx2: ASIC BCM5709 C0 (0x57092003)
bnx2: PCIe x2 5Gbps
bnx2: Coal (RX:6,6,18,18; TX:20,20,80,80)
bnx3 at pci2 dev 0 function 1: Broadcom NetXtreme II BCM5709 1000Base-T
bnx3: Ethernet address 5c:f3:fc:6b:c6:b6
bnx3: interrupting at ioapic1 pin 17
bnx3: ASIC BCM5709 C0 (0x57092003)
bnx3: PCIe x2 5Gbps
bnx3: Coal (RX:6,6,18,18; TX:20,20,80,80)

No MII PHYs?

Sorry, missed them out.

Could you show me:

    0) the dmesg output of the PHYs if available.

All 4 are like this:

bnx0 at pci1 dev 0 function 0: Broadcom NetXtreme II BCM5709 1000Base-T
bnx0: Ethernet address 5c:f3:fc:e4:e6:78
bnx0: interrupting at ioapic1 pin 4
bnx0: ASIC BCM5709 C0 (0x57092003)
bnx0: PCIe x2 5Gbps
bnx0: Coal (RX:6,6,18,18; TX:20,20,80,80)
brgphy0 at bnx0 phy 1: BCM5709 10/100/1000baseT PHY, rev. 8

    1) ifconfig -m

bnx0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
         capabilities=3f00<IP4CSUM_Rx,IP4CSUM_Tx,TCP4CSUM_Rx,TCP4CSUM_Tx>
         capabilities=3f00<UDP4CSUM_Rx,UDP4CSUM_Tx>
         enabled=0
         ec_capabilities=7<VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU>
         ec_enabled=0
         address: 5c:f3:fc:e4:e6:78
         media: Ethernet autoselect (1000baseT full-duplex)
         status: active
         supported Ethernet media:
                 media none
                 media 10baseT
                 media 10baseT mediaopt full-duplex
                 media 100baseTX
                 media 100baseTX mediaopt full-duplex
                 media 1000baseT
                 media 1000baseT mediaopt full-duplex
                 media autoselect
         inet 10.4.0.11 netmask 0xffff0000 broadcast 10.4.255.255
         inet6 fe80::5ef3:fcff:fee4:e678%bnx0 prefixlen 64 scopeid 0x1

Thanks. There is no problem in the output.

    2) pcictl pci0 dump -b [12] -d 0 -f [01]

I only get output for -b 1 -d 0 -f 0:

PCI configuration registers:
   Common header:
     0x00: 0x00791000 0x00100047 0x01040005 0x00000010

     Vendor Name: Symbios Logic (0x1000)
     Device Name: MegaRAID SAS2108 GEN2 (0x0079)

 It's not bnx(4) :)
 And, OK, it's not required because the device is BCM5709 C0 stepping
(P21(The chip marking's formula is different between bge and bnx)).
I have a card which has the same chip.


     Command register: 0x0047
       I/O space accesses: on
       Memory space accesses: on
       Bus mastering: on

(snip)

     0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
     0xf0: 0x00000000 0x00000000 0x00000000 0x00000000


Back to the first mail:

If connected to the Internet and traffic is flowing, it will lock solid after a while

Does the machine recover from the hard hang after stopping the traffic?
e.g. removing cable.

--
-----------------------------------------------
                SAITOH Masanobu (msaitoh%execsw.org@localhost
                                 msaitoh%netbsd.org@localhost)


Home | Main Index | Thread Index | Old Index