Re: working against 5.99.44: AR8131/2 driver

[Ignatios Souvatzis <is%netbsd.org@localhost>]

On Wed, Feb 02, 2011 at 12:40:20AM +0100, Ignatios Souvatzis wrote:

> For the record: with 5.99.43 MONOLITHIC, on the eeepc 1008HA, I only
> get timeout reading phy registers. Lots of timeouts. And Status:
> no network"., whether I use atphy or disable it with boot -c to
> fall back to ukphy

20110129 0000 5.99.44 shows the same error. I'll append the dmesg output
below. Can you post your /var/run/dmesg.boot for comparison, please?

        -is

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010, 2011
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.99.44 (MONOLITHIC) #2: Wed Feb  2 20:48:07 CET 2011
        
ignatios@random87:/var/itch/obj/cur/i386/sys/arch/i386/compile/MONOLITHIC
total memory = 1015 MB
avail memory = 985 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
ASUSTeK Computer INC. 1008HA (x.x)
mainbus0 (root)
cpu0 at mainbus0 apid 0: Intel(R) Atom(TM) CPU N280   @ 1.66GHz, id 0x106c2
cpu1 at mainbus0 apid 1: Intel(R) Atom(TM) CPU N280   @ 1.66GHz, id 0x106c2
ioapic0 at mainbus0 apid 2: pa 0xfec00000, version 20, 24 pins
acpi0 at mainbus0: Intel ACPICA 20100528
acpi0: X/RSDT: OemId <A_M_I_,OEMRSDT ,08000918>, AslId <MSFT,00000097>
acpi0: SCI interrupting at int 9
timecounter: Timecounter "ACPI-Safe" frequency 3579545 Hz quality 900
acpiec0 at acpi0 (EC0, PNP0C09): io 0x62,0x66
P001 (ACPI Object Type 'Processor') at acpi0 not configured
P002 (ACPI Object Type 'Processor') at acpi0 not configured
MCH (PNP0C01) at acpi0 not configured
attimer1 at acpi0 (TMR, PNP0100): io 0x40-0x43 irq 0
pckbc1 at acpi0 (PS2K, PNP0303) (kbd port): io 0x60,0x64 irq 1
pckbc2 at acpi0 (PS2M, SYN0A13) (aux port): irq 12
pcppi1 at acpi0 (SPKR, PNP0800): io 0x61
midi0 at pcppi1: PC speaker
sysbeep0 at pcppi1
npx1 at acpi0 (COPR, PNP0C04): io 0xf0-0xff irq 13
npx1: reported by CPUID; using exception 16
RMSC (PNP0C02) at acpi0 not configured
hpet0 at acpi0 (HPET, PNP0103): mem 0xfed00000-0xfed003ff
timecounter: Timecounter "hpet0" frequency 14318179 Hz quality 2000
OMSC (PNP0C02) at acpi0 not configured
PCIE (PNP0C02) at acpi0 not configured
acpibat0 at acpi0 (BAT0, PNP0C0A-0): ACPI Battery
acpibat0: ASUS LION rechargeable battery
acpibat0: model number 1008HA, serial number  
acpibat0: granularity: low->warn 0.027 Ah, warn->full 0.027 Ah
acpiacad0 at acpi0 (AC0, ACPI0003): ACPI AC Adapter
acpivga0 at acpi0 (VGA): ACPI Display Adapter
acpiout0 at acpivga0 (CRTD, 0x0100): ACPI Display Output Device
acpiout1 at acpivga0 (TVOD, 0x0200): ACPI Display Output Device
acpiout2 at acpivga0 (LCDD, 0x0400): ACPI Display Output Device
acpiout2: brightness levels: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
acpivga0: connected output devices:
acpivga0:   0x0100 (acpiout0): Ext. Monitor, head 0, bios detect
acpivga0:   0x0200 (acpiout1): TV, head 0, bios detect
acpivga0:   0x0400 (acpiout2): Unknown Output Device, head 0, bios detect
acpilid0 at acpi0 (LID, PNP0C0D): ACPI Lid Switch
acpibut0 at acpi0 (SLPB, PNP0C0E): ACPI Sleep Button
RMEM (PNP0C01) at acpi0 not configured
acpibut1 at acpi0 (PWRB, PNP0C0C-170): ACPI Power Button
acpitz0 at acpi0 (TZ00): cpu0 cpu1
acpitz0: levels: critical 90.0 C, passive 85.0 C, passive cooling
acpiwmi0 at acpi0 (AMW0, PNP0C14-0): ACPI WMI Interface
acpiwmibus at acpiwmi0 not configured
apm0 at acpi0: Power Management spec V1.2
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc1 (aux slot)
pms0: Synaptics touchpad version 7.2
pms0: Palm detect
pckbc1: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
attimer1: attached to pcppi1
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0: vendor 0x8086 product 0x27ac (rev. 0x03)
agp0 at pchb0: detected 7932k stolen memory
agp0: aperture at 0xd0000000, size 0x10000000
vga1 at pci0 dev 2 function 0: vendor 0x8086 product 0x27ae (rev. 0x03)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
i915drm0 at vga1: Intel i945GME
i915drm0: AGP at 0xd0000000 256MB
i915drm0: Initialized i915 1.6.0 20080730
vendor 0x8086 product 0x27a6 (miscellaneous display, revision 0x03) at pci0 dev 
2 function 1 not configured
hdaudio0 at pci0 dev 27 function 0: HD Audio Controller
hdaudio0: interrupting at ioapic0 pin 16
hdafg0 at hdaudio0: Realtek ALC269
hdafg0: DAC00 2ch: Speaker [Built-In], HP Out [Jack]
hdafg0: ADC01 2ch: Mic In [Built-In]
hdafg0: ADC02 2ch: Mic In [Jack]
hdafg0: 2ch/2ch 32000Hz 44100Hz 48000Hz 88200Hz 96000Hz 192000Hz 16/16 20/32 
24/32
audio0 at hdafg0: full duplex, playback, capture, independent
ppb0 at pci0 dev 28 function 0: vendor 0x8086 product 0x27d0 (rev. 0x02)
ppb0: PCI Express 1.0 <Root Port of PCI-E Root Complex>
pci1 at ppb0 bus 3
pci1: no spaces enabled!
ppb1 at pci0 dev 28 function 1: vendor 0x8086 product 0x27d2 (rev. 0x02)
ppb1: PCI Express 1.0 <Root Port of PCI-E Root Complex>
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
alc0 at pci2 dev 0 function 0: Attansic/Atheros L1E Ethernet
alc0: ioapic0 pin 17
alc0: Ethernet address 00:26:18:15:30:39
atphy0 at alc0 phy 0: L1 10/100/1000 PHY, rev. 11
atphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, auto
ppb2 at pci0 dev 28 function 2: vendor 0x8086 product 0x27d4 (rev. 0x02)
ppb2: PCI Express 1.0 <Root Port of PCI-E Root Complex>
pci3 at ppb2 bus 1
pci3: memory space enabled, rd/line, wr/inv ok
vendor 0x168c product 0x002b (miscellaneous network, revision 0x01) at pci3 dev 
0 function 0 not configured
uhci0 at pci0 dev 29 function 0: vendor 0x8086 product 0x27c8 (rev. 0x02)
uhci0: interrupting at ioapic0 pin 23
usb0 at uhci0: USB revision 1.0
uhci1 at pci0 dev 29 function 1: vendor 0x8086 product 0x27c9 (rev. 0x02)
uhci1: interrupting at ioapic0 pin 22
usb1 at uhci1: USB revision 1.0
uhci2 at pci0 dev 29 function 2: vendor 0x8086 product 0x27ca (rev. 0x02)
uhci2: interrupting at ioapic0 pin 21
usb2 at uhci2: USB revision 1.0
uhci3 at pci0 dev 29 function 3: vendor 0x8086 product 0x27cb (rev. 0x02)
uhci3: interrupting at ioapic0 pin 20
usb3 at uhci3: USB revision 1.0
ehci0 at pci0 dev 29 function 7: vendor 0x8086 product 0x27cc (rev. 0x02)
ehci0: interrupting at ioapic0 pin 23
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2 uhci3
usb4 at ehci0: USB revision 2.0
ppb3 at pci0 dev 30 function 0: vendor 0x8086 product 0x2448 (rev. 0xe2)
pci4 at ppb3 bus 4
pci4: no spaces enabled!
ichlpcib0 at pci0 dev 31 function 0: vendor 0x8086 product 0x27b9 (rev. 0x02)
timecounter: Timecounter "ichlpcib0" frequency 3579545 Hz quality 1000
ichlpcib0: 24-bit timer
ichlpcib0: TCO (watchdog) timer configured.
gpiobus at ichlpcib0 not configured
ahcisata0 at pci0 dev 31 function 2: vendor 0x8086 product 0x27c5
ahcisata0: interrupting at ioapic0 pin 19
ahcisata0: AHCI revision 1.1, 4 ports, 32 command slots, features 0xc710e000
atabus0 at ahcisata0 channel 0
ichsmb0 at pci0 dev 31 function 3: vendor 0x8086 product 0x27da (rev. 0x02)
ichsmb0: interrupting at ioapic0 pin 19
iic0 at ichsmb0: I2C bus
isa0 at ichlpcib0
isapnp0 at isa0 port 0x279
isapnp0: no ISA Plug 'n Play devices found
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
acpiacad0: AC adapter offline.
uhub0 at usb0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhub3 at usb3: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
uhub4 at usb4: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
ahcisata0 port 0: device present, speed: 1.5Gb/s
wd0 at atabus0 drive 0: <ST9160310AS>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 149 GB, 310101 cyl, 16 head, 63 sec, 512 bytes/sect x 312581808 sectors
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(ahcisata0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) 
(using DMA)
umass0 at uhub4 port 2 configuration 1 interface 0
umass0: Kingston DataTraveler 2.0, rev 2.00/13.c6, addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 1 lun per target
sd0 at scsibus0 target 0 lun 0: <Kingston, DataTraveler 2.0, 1.00> disk 
removable
sd0: 3822 MB, 3936 cyl, 16 head, 32 sec, 512 bytes/sect x 7827456 sectors
uvideo0 at uhub4 port 8 configuration 1 interface 0: GenesysLogic Technology 
Co.,, Ltd.. USB2.0 UVC 1.3M WebCam, rev 2.00/28.01, addr 3
video0 at uvideo0: GenesysLogic Technology Co.,, Ltd.. USB2.0 UVC 1.3M WebCam, 
rev 2.00/28.01, addr 3
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio1 at pad0: half duplex, playback, capture
boot device: sd0
root on sd0a dumps on sd0b
root file system type: ffs
warning: no /dev/console
ubt0 at uhub3 port 1
ubt0: Broadcom Corp BT-253, rev 2.00/2.41, addr 2
alc0: master reset timeout!
alc0: reset timeout(0xffffffff)!
alc0: phy write timeout: phy 0, reg 4
alc0: phy write timeout: phy 0, reg 9
alc0: phy write timeout: phy 0, reg 0
alc0: phy read timeout: phy 0, reg 1
alc0: phy read timeout: phy 0, reg 1
alc0: phy read timeout: phy 0, reg 0
alc0: phy read timeout: phy 0, reg 17
alc0: phy read timeout: phy 0, reg 1
alc0: phy read timeout: phy 0, reg 1
alc0: phy read timeout: phy 0, reg 0
alc0: phy read timeout: phy 0, reg 17
alc0: could not disable RxQ/TxQ (0xffffffff)!
alc0: could not disable Rx/Tx MAC(0xffffffff)!
alc0: master reset timeout!
alc0: reset timeout(0xffffffff)!
alc0: phy write timeout: phy 0, reg 4
alc0: phy write timeout: phy 0, reg 9
alc0: phy write timeout: phy 0, reg 0
alc0: phy read timeout: phy 0, reg 1
alc0: phy read timeout: phy 0, reg 1
alc0: phy read timeout: phy 0, reg 0
alc0: phy read timeout: phy 0, reg 17
alc0: DMA read error! -- resetting
alc0: DMA write error! -- resetting
alc0: TxQ reset! -- resetting
alc0: phy read timeout: phy 0, reg 1
alc0: phy read timeout: phy 0, reg 1
alc0: phy read timeout: phy 0, reg 0
alc0: phy read timeout: phy 0, reg 17
alc0: could not disable RxQ/TxQ (0xffffffff)!
alc0: could not disable Rx/Tx MAC(0xffffffff)!
alc0: master reset timeout!
alc0: reset timeout(0xffffffff)!
alc0: phy write timeout: phy 0, reg 4
alc0: phy write timeout: phy 0, reg 9
alc0: phy write timeout: phy 0, reg 0
alc0: phy read timeout: phy 0, reg 1
alc0: phy read timeout: phy 0, reg 1
alc0: phy read timeout: phy 0, reg 0
alc0: phy read timeout: phy 0, reg 17
alc0: phy read timeout: phy 0, reg 1
alc0: phy read timeout: phy 0, reg 1
alc0: phy read timeout: phy 0, reg 1
alc0: phy read timeout: phy 0, reg 1
alc0: phy read timeout: phy 0, reg 0
alc0: phy read timeout: phy 0, reg 17
alc0: phy read timeout: phy 0, reg 1
alc0: phy read timeout: phy 0, reg 1
alc0: phy read timeout: phy 0, reg 1
alc0: phy read timeout: phy 0, reg 1
alc0: phy read timeout: phy 0, reg 0
alc0: phy read timeout: phy 0, reg 17
alc0: phy read timeout: phy 0, reg 1
alc0: phy read timeout: phy 0, reg 1
alc0: phy read timeout: phy 0, reg 1
alc0: phy read timeout: phy 0, reg 1
alc0: phy read timeout: phy 0, reg 0
alc0: phy read timeout: phy 0, reg 17
alc0: phy read timeout: phy 0, reg 1
alc0: phy read timeout: phy 0, reg 1
alc0: phy read timeout: phy 0, reg 1
alc0: phy read timeout: phy 0, reg 1
alc0: phy read timeout: phy 0, reg 0
alc0: phy read timeout: phy 0, reg 17
alc0: phy read timeout: phy 0, reg 1
alc0: phy read timeout: phy 0, reg 1
alc0: phy read timeout: phy 0, reg 0
alc0: phy read timeout: phy 0, reg 17
alc0: could not disable RxQ/TxQ (0xffffffff)!
alc0: could not disable Rx/Tx MAC(0xffffffff)!