NetBSD 5 RC2, marvell ethernet card problem

[Srdjan Rilak <sleep.walk%yahoo.com@localhost>]

Hi!

I just installed NetBSD 5.0 RC2 and I have some problems with my ethernet 
controller.

The device is identified as "Marvell Yukon 88E8040 PCI-E Fast Ethernet 
Controller" (integrated on Dell Inspiron's board), and dmesg says that some 
function don't work:

pci1 at ppb0 bus 9
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
vendor 0x11ab product 0x4354 (ethernet network, revision 0x12) at pci1 dev 0 
function 0 not configured
ppb1 at pci0 dev 28 function 1: vendor 0x8086 product 0x2841 (rev. 0x02)

Is the device suppoorted with msk(c) or some other driver?
If so, is there a way to make this device work? ;)

Entire dmesg's output follows.


Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.0_RC2 (GENERIC) #0: Mon Feb  9 10:11:20 UTC 2009
    
builds%b4.netbsd.org@localhost:/home/builds/ab/netbsd-5-0-RC2/i386/200902090142Z-obj/home/builds/ab/netbsd-5-0-RC2/src/sys/arch/i386/compile/GENERIC
total memory = 2038 MB
avail memory = 1991 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
Dell Inc. Inspiron 1525                  
mainbus0 (root)
ACPI Exception (tbxface-0657): AE_AML_NO_OPERAND, While loading namespace from 
ACPI tables [20080321]
ACPI: unable to load tables: AE_AML_NO_OPERAND
cpu0 at mainbus0: Intel 686-class, 1828MHz, id 0x6fd
cpu0: Enhanced SpeedStep (1388 mV) 1833 MHz
cpu0: Enhanced SpeedStep frequencies available (MHz): 1833 1667 1500 1333 1167 
1000
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x8086 product 0x2a00 (rev. 0x0c)
agp0 at pchb0: detected 7676k stolen memory
agp0: aperture at 0xe0000000, size 0x20000000
vga1 at pci0 dev 2 function 0: vendor 0x8086 product 0x2a02 (rev. 0x0c)
vga1: WARNING: ignoring 64-bit BAR @ 0x10
vga1: WARNING: ignoring 64-bit BAR @ 0x18
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
drm at vga1 not configured
vendor 0x8086 product 0x2a03 (miscellaneous display, revision 0x0c) at pci0 dev 
2 function 1 not configured
uhci0 at pci0 dev 26 function 0: vendor 0x8086 product 0x2834 (rev. 0x02)
uhci0: interrupting at irq 10
usb0 at uhci0: USB revision 1.0
uhci1 at pci0 dev 26 function 1: vendor 0x8086 product 0x2835 (rev. 0x02)
uhci1: interrupting at irq 9
usb1 at uhci1: USB revision 1.0
ehci0 at pci0 dev 26 function 7: vendor 0x8086 product 0x283a (rev. 0x02)
ehci0: interrupting at irq 7
ehci0: BIOS has given up ownership
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1
usb2 at ehci0: USB revision 2.0
azalia0 at pci0 dev 27 function 0: Generic High Definition Audio Controller
azalia0: interrupting at irq 9
azalia0: host: 0x8086/0x284b (rev. 2), HDA rev. 1.0
ppb0 at pci0 dev 28 function 0: vendor 0x8086 product 0x283f (rev. 0x02)
pci1 at ppb0 bus 9
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
vendor 0x11ab product 0x4354 (ethernet network, revision 0x12) at pci1 dev 0 
function 0 not configured
ppb1 at pci0 dev 28 function 1: vendor 0x8086 product 0x2841 (rev. 0x02)
pci2 at ppb1 bus 11
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
vendor 0x14e4 product 0x4315 (miscellaneous network, revision 0x01) at pci2 dev 
0 function 0 not configured
ppb2 at pci0 dev 28 function 4: vendor 0x8086 product 0x2847 (rev. 0x02)
pci3 at ppb2 bus 12
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
uhci2 at pci0 dev 29 function 0: vendor 0x8086 product 0x2830 (rev. 0x02)
uhci2: interrupting at irq 10
usb3 at uhci2: USB revision 1.0
uhci3 at pci0 dev 29 function 1: vendor 0x8086 product 0x2831 (rev. 0x02)
uhci3: interrupting at irq 9
usb4 at uhci3: USB revision 1.0
uhci4 at pci0 dev 29 function 2: vendor 0x8086 product 0x2832 (rev. 0x02)
uhci4: interrupting at irq 7
usb5 at uhci4: USB revision 1.0
ehci1 at pci0 dev 29 function 7: vendor 0x8086 product 0x2836 (rev. 0x02)
ehci1: interrupting at irq 10
ehci1: BIOS refuses to give up ownership, using force
ehci1: EHCI version 1.0
ehci1: companion controllers, 2 ports each: uhci2 uhci3 uhci4
usb6 at ehci1: USB revision 2.0
ppb3 at pci0 dev 30 function 0: vendor 0x8086 product 0x2448 (rev. 0xf2)
pci4 at ppb3 bus 2
pci4: i/o space, memory space enabled
fwohci0 at pci4 dev 9 function 0: vendor 0x1180 product 0x0832 (rev. 0x05)
fwohci0: interrupting at irq 11
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 4a:4f:c0:00:39:ae:5c:70
fwohci0: Phy 1394a available S400, 1 ports.
fwohci0: Link S400, max_rec 2048 bytes.
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwohci0: Initiate bus reset
vendor 0x1180 product 0x0822 (SD Host Controller system, interface 0x01, 
revision 0x22) at pci4 dev 9 function 1 not configured
vendor 0x1180 product 0x0843 (miscellaneous system, revision 0x12) at pci4 dev 
9 function 2 not configured
vendor 0x1180 product 0x0592 (miscellaneous system, revision 0x12) at pci4 dev 
9 function 3 not configured
vendor 0x1180 product 0x0852 (miscellaneous system, revision 0x12) at pci4 dev 
9 function 4 not configured
ichlpcib0 at pci0 dev 31 function 0
ichlpcib0: vendor 0x8086 product 0x2815 (rev. 0x02)
timecounter: Timecounter "ichlpcib0" frequency 3579545 Hz quality 1000
ichlpcib0: 24-bit timer
ichlpcib0: TCO (watchdog) timer configured.
piixide0 at pci0 dev 31 function 1
piixide0: Intel 82801HBM IDE Controller (ICH8M) (rev. 0x02)
piixide0: bus-master DMA support present
piixide0: primary channel configured to compatibility mode
piixide0: primary channel interrupting at irq 14
atabus0 at piixide0 channel 0
piixide0: secondary channel configured to compatibility mode
piixide0: secondary channel ignored (disabled)
piixide1 at pci0 dev 31 function 2
piixide1: Intel 82801HEM Serial ATA Controller (ICH8M) (rev. 0x02)
piixide1: bus-master DMA support present
piixide1: primary channel configured to native-PCI mode
piixide1: using irq 10 for native-PCI interrupt
atabus1 at piixide1 channel 0
piixide1: secondary channel configured to native-PCI mode
atabus2 at piixide1 channel 1
ichsmb0 at pci0 dev 31 function 3: vendor 0x8086 product 0x283e (rev. 0x02)
ichsmb0: interrupting at irq 10
iic0 at ichsmb0: I2C bus
isa0 at ichlpcib0
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
attimer0 at isa0 port 0x40-0x43: AT Timer
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker (CPU-intensive output)
sysbeep0 at pcppi0
npx0 at isa0 port 0xf0-0xff
npx0: reported by CPUID; using exception 16
attimer0: attached to pcppi0
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
ieee1394if0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
ieee1394if0: bus manager 0 (me)
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "TSC" frequency 1828856590 Hz quality 3000
azalia0: codec[0]: 0x14f1/0x2c06 (rev. 0.0), HDA rev. 1.0
azalia0: codec[0]: No support for modem function groups
azalia0: codec[0] has no audio function groups
azalia0: codec[1]: 0x1095/0x1392 (rev. 0.0), HDA rev. 1.0
azalia0: codec[2]: Sigmatel STAC9228X (rev. 2.1), HDA rev. 1.0
audio0 at azalia0: full duplex, independent
uhub0 at usb0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 4 ports with 4 removable, self powered
atapibus0 at atabus0: 2 targets
uhub3 at usb3: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
uhub4 at usb4: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub4: 2 ports with 2 removable, self powered
uhub5 at usb5: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub5: 2 ports with 2 removable, self powered
uhub6 at usb6: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub6: 6 ports with 6 removable, self powered
cd0 at atapibus0 drive 0: <HL-DT-ST DVD+/-RW GSA-T21N, KZ184GK2135, A102> cdrom 
removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
cd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
uvideo0 at uhub2 port 1 configuration 1 interface 0: OmniVision Technologies, 
Inc. -2640-07.07.20.3 Laptop Integrated Webcam, rev 2.00/1.00, addr 2
video0 at uvideo0: OmniVision Technologies, Inc. -2640-07.07.20.3 Laptop 
Integrated Webcam, rev 2.00/1.00, addr 2
uhidev0 at uhub4 port 1 configuration 1 interface 0
uhidev0: Genius 4D Scroll Mouse, rev 1.10/0.00, addr 2, iclass 3/1
ums0 at uhidev0: 3 buttons and Z dir.
wsmouse1 at ums0 mux 0
wd0 at atabus1 drive 0: <ST9160827AS>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 149 GB, 310101 cyl, 16 head, 63 sec, 512 bytes/sect x 312581808 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(piixide1:0:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio1 at pad0: half duplex
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)




Tnx for answering, ans sorry about my poor english.