Hello, I'm running NetBSD/i386 5.99.24 on an MSI board with an ATI Radeon 2400 XT plugged in. To have 2d acceleration and XVideo, I load radeondrm.kmod at boottime. It usually works, but after restarting X sufficiently often, it suddenly stops; that is, either display is corrupted, or X does not find DRI support anymore. There are a few pecularities: >From dmesg (which is also attached): agp0 at pchb0: can't find internal VGA device config space ... ppb0: unsupported PCI Express version ... vga1: WARNING: ignoring 64-bit BAR @ 0x10 vga1: WARNING: ignoring 64-bit BAR @ 0x18 and, after each restart of X: info: [drm] Setting GART location based on new memory map info: [drm] Loading RV610 Microcode info: [drm] Resetting GPU info: [drm] writeback test failed ffffffff deadbeef Usually, after a while I get a message that something failed; I think it has to do with the memory map, but unfortunately I can't reproduce it at the moment. Trying to reproduce the problem, I tried to fill up RAM and make the system use swap. Indeed, radeondrm then got detached: radeondrm0: detached Attached is an Xorg.0.log from after the problem occured. The following lines seem suspicious to me: drmOpenDevice: node name is /dev/dri/card0 drmOpenDevice: open result is 7, (OK) drmOpenDevice: node name is /dev/dri/card0 drmOpenDevice: open result is 7, (OK) drmGetBusid returned '' ... (II) RADEONHD(0): [drm] failure adding irq handler, there is a device already using that irq [drm] falling back to irq-free operation One time, X would crash, leaving 200000 lines saying (EE) RADEONHD(0): RHDDRMCPBuffer: drmDMA returned -6 It would be very nice if someone could look into this. Assuming that perhaps more info is needed: does it suffice to sysctl -w hw.dri.debug=1, or would I have to compile a kernel with DRM_DEBUG? Many TIA, Dennis den Brok
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008, 2009, 2010
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 5.99.24 (GENERIC) #0: Thu Mar 18 17:34:26 UTC 2010
builds%b8.netbsd.org@localhost:/home/builds/ab/HEAD/i386/201003180000Z-obj/home/builds/ab/HEAD/src/sys/arch/i386/compile/GENERIC
total memory = 2047 MB
avail memory = 2000 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
MICRO-STAR INTERNATIONAL CO.,LTD MS-7519 (1.0)
mainbus0 (root)
cpu0 at mainbus0 apid 0: Intel 686-class, 2673MHz, id 0x10676
cpu1 at mainbus0 apid 1: Intel 686-class, 2673MHz, id 0x10676
ioapic0 at mainbus0 apid 2: pa 0xfec00000, version 20, 24 pins
acpi0 at mainbus0: Intel ACPICA 20090730
acpi0: X/RSDT: OemId <7519MS,A7519200,20080730>, AslId <MSFT,00000097>
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
ACPI-Fast 24-bit timer
attimer1 at acpi0 (TMR, PNP0100): io 0x40-0x43 irq 0
pcppi1 at acpi0 (SPKR, PNP0800): io 0x61
midi0 at pcppi1: PC speaker
sysbeep0 at pcppi1
npx1 at acpi0 (COPR, PNP0C04): io 0xf0-0xff irq 13
npx1: reported by CPUID; using exception 16
UAR1 (PNP0501) at acpi0 not configured
hpet0 at acpi0 (HPET, PNP0103): mem 0xfed00000-0xfed003ff
timecounter: Timecounter "hpet0" frequency 14318179 Hz quality 2000
pckbc1 at acpi0 (PS2K, PNP0303) (kbd port): io 0x60,0x64 irq 1
pckbc2 at acpi0 (PS2M, PNP0F03) (aux port): irq 12
acpibut0 at acpi0 (PWRB, PNP0C0C-170): ACPI Power Button
apm0 at acpi0: Power Management spec V1.2
attimer1: attached to pcppi1
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc1 (aux slot)
pckbc1: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0: vendor 0x8086 product 0x2e20 (rev. 0x03)
agp0 at pchb0: can't find internal VGA device config space
ppb0 at pci0 dev 1 function 0: vendor 0x8086 product 0x2e21 (rev. 0x03)
ppb0: unsupported PCI Express version
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
vga1 at pci1 dev 0 function 0: vendor 0x1002 product 0x94c1 (rev. 0x00)
vga1: WARNING: ignoring 64-bit BAR @ 0x10
vga1: WARNING: ignoring 64-bit BAR @ 0x18
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
drm at vga1 not configured
hdaudio0 at pci1 dev 0 function 1: HD Audio Controller
hdaudio0: interrupting at ioapic0 pin 17
hdafg0 at hdaudio0 vendor 0x1002 product 0xAA01 nid 0x01 (firmware
configuration)
hdafg0: DAC0:02, Digital Digital Other Out: Jack (Unknown, 03)
hdafg0: 2ch/0ch 48000Hz 16/16
audio0 at hdafg0: half duplex, playback
uhci0 at pci0 dev 26 function 0: vendor 0x8086 product 0x3a37 (rev. 0x00)
uhci0: interrupting at ioapic0 pin 16
usb0 at uhci0: USB revision 1.0
uhci1 at pci0 dev 26 function 1: vendor 0x8086 product 0x3a38 (rev. 0x00)
uhci1: interrupting at ioapic0 pin 21
usb1 at uhci1: USB revision 1.0
uhci2 at pci0 dev 26 function 2: vendor 0x8086 product 0x3a39 (rev. 0x00)
uhci2: interrupting at ioapic0 pin 19
usb2 at uhci2: USB revision 1.0
ehci0 at pci0 dev 26 function 7: vendor 0x8086 product 0x3a3c (rev. 0x00)
ehci0: interrupting at ioapic0 pin 18
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2
usb3 at ehci0: USB revision 2.0
hdaudio1 at pci0 dev 27 function 0: HD Audio Controller
hdaudio1: interrupting at ioapic0 pin 22
hdafg1 at hdaudio1 vendor 0x10EC product 0x0888 nid 0x01 (firmware
configuration)
hdafg1: DAC0:02, Analog Speaker: Jack (Green, 14)
hdafg1: DAC0:03, Analog Speaker: Jack (Orange, 16)
hdafg1: DAC0:04, Analog Speaker: Jack (Black, 15)
hdafg1: DAC0:05, Analog Speaker: Jack (Grey, 17)
hdafg1: DAC1:25, Analog HP Out: Jack (Green, 1B)
hdafg1: DAC2:06, Digital SPDIF Out: Jack (Black, 1E)
hdafg1: ADC3:08, Analog Mic In: Jack (Pink, 18)
hdafg1: ADC3:08, Analog Line In: Jack (Blue, 1A)
hdafg1: ADC4:09, Analog Mic In: Jack (Pink, 19)
hdafg1: 8ch/2ch 44100Hz-192000Hz 16/16 20/32 24/32
audio1 at hdafg1: full duplex, playback, capture, independent
ppb1 at pci0 dev 28 function 0: vendor 0x8086 product 0x3a40 (rev. 0x00)
pci2 at ppb1 bus 2
pci2: i/o space enabled, rd/line, wr/inv ok
jmide0 at pci2 dev 0 function 0: vendor 0x197b product 0x2368
jmide0: 1 PATA port
jmide0: interrupting at ioapic0 pin 16
jmide0: PCI IDE interface used
jmide0: bus-master DMA support present
jmide0: primary channel wired to native-PCI mode
jmide0: primary channel is PATA
atabus0 at jmide0 channel 0
jmide0: secondary channel wired to native-PCI mode
jmide0: secondary channel is unused
ppb2 at pci0 dev 28 function 1: vendor 0x8086 product 0x3a42 (rev. 0x00)
pci3 at ppb2 bus 3
pci3: no spaces enabled!
ppb3 at pci0 dev 28 function 5: vendor 0x8086 product 0x3a4a (rev. 0x00)
pci4 at ppb3 bus 4
pci4: i/o space, memory space enabled, rd/line, wr/inv ok
re0 at pci4 dev 0 function 0: RealTek 8168/8111 PCIe Gigabit Ethernet (rev.
0x02)
re0: interrupting at ioapic0 pin 17
re0: Ethernet address 00:21:85:5d:f0:97
re0: using 256 tx descriptors
rgephy0 at re0 phy 7: RTL8169S/8110S/8211 1000BASE-T media interface, rev. 2
rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
uhci3 at pci0 dev 29 function 0: vendor 0x8086 product 0x3a34 (rev. 0x00)
uhci3: interrupting at ioapic0 pin 23
usb4 at uhci3: USB revision 1.0
uhci4 at pci0 dev 29 function 1: vendor 0x8086 product 0x3a35 (rev. 0x00)
uhci4: interrupting at ioapic0 pin 19
usb5 at uhci4: USB revision 1.0
uhci5 at pci0 dev 29 function 2: vendor 0x8086 product 0x3a36 (rev. 0x00)
uhci5: interrupting at ioapic0 pin 18
usb6 at uhci5: USB revision 1.0
ehci1 at pci0 dev 29 function 7: vendor 0x8086 product 0x3a3a (rev. 0x00)
ehci1: interrupting at ioapic0 pin 23
ehci1: EHCI version 1.0
ehci1: companion controllers, 2 ports each: uhci3 uhci4 uhci5
usb7 at ehci1: USB revision 2.0
ppb4 at pci0 dev 30 function 0: vendor 0x8086 product 0x244e (rev. 0x90)
pci5 at ppb4 bus 5
pci5: no spaces enabled!
pcib0 at pci0 dev 31 function 0: vendor 0x8086 product 0x3a18 (rev. 0x00)
piixide0 at pci0 dev 31 function 2: Intel ICH10 Serial ATA 2 Controller 4x2
(rev. 0x00)
piixide0: bus-master DMA support present
piixide0: primary channel configured to native-PCI mode
piixide0: using ioapic0 pin 19 for native-PCI interrupt
atabus1 at piixide0 channel 0
piixide0: secondary channel configured to native-PCI mode
atabus2 at piixide0 channel 1
ichsmb0 at pci0 dev 31 function 3: vendor 0x8086 product 0x3a30 (rev. 0x00)
ichsmb0: interrupting at ioapic0 pin 18
iic0 at ichsmb0: I2C bus
piixide1 at pci0 dev 31 function 5: Intel ICH10 Serial ATA 2 Controller 2x2
(rev. 0x00)
piixide1: bus-master DMA support present
piixide1: primary channel wired to native-PCI mode
piixide1: using ioapic0 pin 19 for native-PCI interrupt
atabus3 at piixide1 channel 0
piixide1: secondary channel wired to native-PCI mode
atabus4 at piixide1 channel 1
isa0 at pcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
uhub0 at usb0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhub3 at usb3: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 6 ports with 6 removable, self powered
uhub4 at usb4: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub4: 2 ports with 2 removable, self powered
uhub5 at usb5: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub5: 2 ports with 2 removable, self powered
uhub6 at usb6: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub6: 2 ports with 2 removable, self powered
uhub7 at usb7: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub7: 6 ports with 6 removable, self powered
radeondrm0 at vga1: Radeon HD 2400 XT
radeondrm0: Initialized radeon 1.29.0 20080613
ugen0 at uhub3 port 3
ugen0: Canon CanoScan, rev 2.00/3.06, addr 2
wd0 at atabus0 drive 0: <SanDisk SDCFX3-004G>
wd0: drive supports 4-sector PIO transfers, LBA addressing
wd0: 3919 MB, 7964 cyl, 16 head, 63 sec, 512 bytes/sect x 8027712 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 4 (Ultra/66)
wd0(jmide0:0:0): using PIO mode 4, Ultra-DMA mode 4 (Ultra/66) (using DMA)
wd1 at atabus3 drive 0: <ST3250410AS>
wd1: drive supports 16-sector PIO transfers, LBA48 addressing
wd1: 232 GB, 484521 cyl, 16 head, 63 sec, 512 bytes/sect x 488397168 sectors
wd1: 32-bit data port
wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd1(piixide1:0:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio2 at pad0: half duplex, playback, capture
WARNING: 5 errors while detecting hardware; check system log.
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
warning: no /dev/console
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
info: [drm] Setting GART location based on new memory map
info: [drm] Loading RV610 Microcode
info: [drm] Resetting GPU
info: [drm] writeback test failed ffffffff deadbeef
radeondrm0: unable to detach instance
radeondrm0: unable to detach instance
radeondrm0: unable to detach instance
radeondrm0: unable to detach instance
radeondrm0: unable to detach instance
radeondrm0: unable to detach instance
radeondrm0: unable to detach instance
radeondrm0: unable to detach instance
radeondrm0: unable to detach instance
radeondrm0: unable to detach instance
radeondrm0: unable to detach instance
radeondrm0: unable to detach instance
radeondrm0: unable to detach instance
Attachment:
Xorg.0.log
Description: Binary data