Re: Hardware-Empfehlung für NetBSD-Router

[Hubert Feyrer <hubert%feyrer.de@localhost>]

On Thu, 2 Dec 2010, Jens Rehsack wrote:
> Ich suche daher ein Gerät, das mindestens 4 unabhängig ansteuerbare
> Netzwerkports hat, möglichst wenig Strom verbraucht und von NetBSD
> unterstützt wird.

Wenn nur 3 Ports reichen: Alix von PC Engines
http://www.pcengines.ch/alix.htm


 - Hubert


Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.1_RC3 (NB5) #1: Mon Jul 12 23:33:47 CEST 2010

feyrer@localhost:/NB5
total memory = 255 MB
avail memory = 247 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
Generic PC
PCI BIOS rev. 2.1 found at 0xfcec9
pcibios: config mechanism [1][x], special cycles [1][x], last bus 0
pcibios_get_intr_routing: function not supported
No PCI IRQ Routing information available.
mainbus0 (root)
cpu0 at mainbus0: AMD 586-class, 498MHz, id 0x5a2
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 1 function 0
pchb0: vendor 0x1022 product 0x2080 (rev. 0x33)
vendor 0x1022 product 0x2082 (entertainment crypto) at pci0 dev 1 function 
2 not configured
vr0 at pci0 dev 9 function 0: VIA VT6105M (Rhine III) 10/100 Ethernet
vr0: interrupting at irq 10
vr0: Ethernet address: 00:0d:b9:15:24:04
ukphy0 at vr0 phy 1: Generic IEEE 802.3u media interface
ukphy0: OUI 0x0002c6, model 0x0034, rev. 3
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
vr1 at pci0 dev 10 function 0: VIA VT6105M (Rhine III) 10/100 Ethernet
vr1: interrupting at irq 11
vr1: Ethernet address: 00:0d:b9:15:24:05
ukphy1 at vr1 phy 1: Generic IEEE 802.3u media interface
ukphy1: OUI 0x0002c6, model 0x0034, rev. 3
ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
vr2 at pci0 dev 11 function 0: VIA VT6105M (Rhine III) 10/100 Ethernet
vr2: interrupting at irq 15
vr2: Ethernet address: 00:0d:b9:15:24:06
ukphy2 at vr2 phy 1: Generic IEEE 802.3u media interface
ukphy2: OUI 0x0002c6, model 0x0034, rev. 3
ukphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pcib0 at pci0 dev 15 function 0
pcib0: vendor 0x1022 product 0x2090 (rev. 0x03)
viaide0 at pci0 dev 15 function 2
viaide0: Advanced Micro Devices CS5536 IDE Controller (rev. 0x01)
viaide0: bus-master DMA support present
viaide0: primary channel wired to compatibility mode
viaide0: primary channel interrupting at irq 14
atabus0 at viaide0 channel 0
viaide0: secondary channel wired to compatibility mode
viaide0: secondary channel ignored (disabled)
vendor 0x1022 product 0x2094 (USB serial bus, interface 0x10, revision 
0x02) at pci0 dev 15 function 4 not configured
vendor 0x1022 product 0x2095 (USB serial bus, interface 0x20, revision 
0x02) at pci0 dev 15 function 5 not configured
isa0 at pcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com0: console
attimer0 at isa0 port 0x40-0x43: AT Timer
pcppi0 at isa0 port 0x61
sysbeep0 at pcppi0
npx0 at isa0 port 0xf0-0xff
npx0: reported by CPUID; using exception 16
attimer0: attached to pcppi0
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "TSC" frequency 498078220 Hz quality -100
wd0 at atabus0 drive 0initializing IPsec...: <SECUDOS 4GB CF>
wd0: drive supports 1-sector PIO transfers, LBA addressing
wd0: 3882 MB, 7889 cyl, 16 head, 63 sec, 512 bytes/sect x 7952112 sectors
IPsec: Initialized Security Association Processing.
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 4 (Ultra/66)
wd0(viaide0:0:0): using PIO mode 4, Ultra-DMA mode 4 (Ultra/66) (using 
DMA)
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs