[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index][Old Index]
I just finished installation of NetBSD 6.0 on my Fujitsu-Siemens
Storagebird LAN 2 (SBLAN2). dmesg appended.
The SBLAN2 seems to be a stripped-down version of the NH-231, with no
USB, no external SATA port, and apparently no RTC (???).
I will take pictures of the PCB, maybe it really has no RTC, or
something is broken for the SBLAN2.
According to the Linux sources, two versions of the SBLAN2 exist:
Hw-Rev. 1.0 (called NH-222A in the sources) and 1.1 (NH-222B).
The difference seems to be the CPU (and RAM speed?), clocked 266 MHz
on Rev. 1.0, and only 200 MHz on Rev. 1.1.
I was lucky enough to get a NH-222A though.
Netronix also has a NH222 on their website:
My box looks exactly like this, but with different color, branding etc.
One thing I noticed: Why does NetBSD use a different MAC address (the
last 3 bytes) than it is shown (and used) by ppcboot?
- - - - -
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008, 2009, 2010, 2011, 2012
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 6.0 (GENERIC)
total memory = 65536 KB
avail memory = 59440 KB
OpenPIC Version 1.2: Supports 1 CPUs and 26 interrupt sources.
timecounter: Timecounters tick every 10.000 msec
cpu0 at mainbus0: 8245 (Revision 0.4), ID 0 (primary)
cpu0: HID0 0x90c000<DOZE,DPM,ICE,DCE>, powersave: 1
cpu0: 264.00 MHz
eumb0 at mainbus0
com0 at eumb0 unit 0: ns16550a, working fifo
com0: interrupting at irq 40
ociic0 at eumb0
iic0 at ociic0: I2C bus
pcf8563rtc0 at iic0 addr 0x51: NXP PCF8563 Real-time Clock
satmgr0 at eumb0 unit 1: button manager (not supported)
nhpow0 at mainbus0: NH230/231 gpio board control, version 0
nhpow0: interrupting at irq 20
gpio0 at nhpow0: 8 pins
cfi at mainbus0 not configured
pci0 at mainbus0 bus 0
pci0: i/o space, memory space enabled
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x1057 product 0x0006 (rev. 0x14)
re0 at pci0 dev 15 function 0: RealTek 8169/8110 Gigabit Ethernet (rev. 0x10)
re0: interrupting at irq 17
re0: Ethernet address 00:08:54:xx:xx:xx
re0: using 256 tx descriptors
rgephy0 at re0 phy 7: RTL8169S/8110S/8211 1000BASE-T media interface, rev. 0
rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
satalink0 at pci0 dev 16 function 0: Silicon Image SATALink 3512 (rev. 0x01)
satalink0: SATALink BA5 register space disabled
satalink0: bus-master DMA support present
satalink0: primary channel wired to native-PCI mode
satalink0: using irq 18 for native-PCI interrupt
atabus0 at satalink0 channel 0
satalink0: secondary channel wired to native-PCI mode
atabus1 at satalink0 channel 1
vmmask 18000000 schedmask 38000000 highmask 78000000
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "mftb" frequency 33000000 Hz quality 100
satalink0: port 0: device present, speed: 1.5Gb/s
wd0 at atabus0 drive 0
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 372 GB, 775221 cyl, 16 head, 63 sec, 512 bytes/sect x 781422768 sectors
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(satalink0:0:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
Kernelized RAIDframe activated
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
pcf8563rtc0: read failed
WARNING: preposterous TOD clock time
WARNING: using filesystem time
WARNING: CHECK AND RESET THE DATE!
pcf8563rtc0: write failed
Cannot set TOD clock time
Main Index |
Thread Index |