Re: 6.0_BETA boot doesn't complete

To: port-i386%netbsd.org@localhost
Subject: Re: 6.0_BETA boot doesn't complete
From: Ray Phillips <r.phillips%uq.edu.au@localhost>
Date: Sun, 18 Mar 2012 17:19:54 +1000

The mode messages are now under aprint_verbose(); I guess boot -v would
show them.


The terminal output using boot -v is shown below.  As you can see,
answering cd0d for the `root device (default cd0a):' question seems
to have got it working -- using the boot-com.iso image anyway.  With
the boot.iso image only an occassional character that was typed in
response to that prompt appeared on the console and the Enter key did
nothing, so I couldn't find out what effect cd0d had with it.


Ray

 NetBSD/x86 BIOS Boot, Revision 5.9 (from NetBSD 6.0_BETA)
 Memory: 639/3135744 k

Press return to boot now, any other key for boot menu
booting cd0a:netbsd - starting in 0 seconds.

 boot -v

booting cd0a:netbsd (howto 0x20000)
11686192+564132+483896 [595984+584948]=0xd47a10
úBIOS CFG: Model-SubM-Rev: fc-01-00, 0x0x74<EBDA,KBDINT,RTC,IC2>
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010, 2011, 2012
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 6.0_BETA (GENERIC)
total memory = 3062 MB
avail memory = 2999 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
                                                                (
)
mainbus0 (root)
cpu0 at mainbus0 apid 0timecounter: Timecounter "lapic" frequency
200079445 Hz quality -100
: Intel(R) Pentium(R) 4 CPU 3.00GHz, id 0xf41
cpu1 at mainbus0 apid 1: Intel(R) Pentium(R) 4 CPU 3.00GHz, id 0xf41
ioapic0 at mainbus0 apid 2: pa 0xfec00000, version 20, 24 pins
acpi0 at mainbus0: Intel ACPICA 20110623
acpi0: X/RSDT: OemId <INTEL ,D915GAG ,20050128>, AslId <MSFT,00000097>
acpi0: SCI interrupting at int 9
timecounter: Timecounter "ACPI-Safe" frequency 3579545 Hz quality 900
attimer1 at acpi0 (TMR, PNP0100): io 0x40-0x43 irq 0
pckbc1 at acpi0 (PS2K, PNP0303) (kbd port): io 0x60,0x64 irq 1
pckbc2 at acpi0 (PS2M, PNP0F03) (aux port): irq 12
pcppi1 at acpi0 (SPKR, PNP0800): io 0x61
midi0 at pcppi1: PC speaker
sysbeep0 at pcppi1
npx1 at acpi0 (COPR, PNP0C04): io 0xf0-0xff irq 13
npx1: reported by CPUID; using exception 16
FDC0 (PNP0700) at acpi0 not configured
UAR1 (PNP0501) at acpi0 not configured
LPT (PNP0400) at acpi0 not configured
RMSC (PNP0C02) at acpi0 not configured
FWH (INT0800) at acpi0 not configured
FWHE (PNP0C02) at acpi0 not configured
OMSC (PNP0C02) at acpi0 not configured
RMEM (PNP0C01) at acpi0 not configured
acpibut0 at acpi0 (PWRB, PNP0C0C-170): ACPI Power Button
apm0 at acpi0: Power Management spec V1.2
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0 mux 1
pms0 at pckbc1 (aux slot)
pckbc1: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
attimer1: attached to pcppi1
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0: vendor 0x8086 product 0x2580 (rev. 0x04)
agp0 at pchb0: detected 7932k stolen memory
agp0: aperture at 0xc0000000, size 0x10000000
ppb0 at pci0 dev 1 function 0: vendor 0x8086 product 0x2581 (rev. 0x04)
ppb0: PCI Express 1.0 <Root Port of PCI-E Root Complex>
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
vga1 at pci0 dev 2 function 0: vendor 0x8086 product 0x2582 (rev. 0x04)
wsdisplay0 at vga1 kbdmux 1
wsmux1: connecting to wsdisplay0
wskbd0: connecting to wsdisplay0
i915drm0 at vga1: Intel i915G
i915drm0: AGP at 0xc0000000 256MB
i915drm0: Initialized i915 1.6.0 20080730
hdaudio0 at pci0 dev 27 function 0: HD Audio Controller
hdaudio0: interrupting at ioapic0 pin 16
hdafg0 at hdaudio0: Realtek ALC880
hdafg0: DAC00 2ch: Speaker [Jack]
hdafg0: DAC01 2ch: HP Out [Jack]
hdafg0: ADC02 2ch: CD [Built-In], Line In [Jack], Mic In [Jack]
hdafg0: ADC03 2ch: Mic In [Jack]
hdafg0: 2ch/2ch 44100Hz 48000Hz 96000Hz 192000Hz PCM16 PCM20 PCM24 AC3
audio0 at hdafg0: full duplex, playback, capture, independent
ppb1 at pci0 dev 28 function 0: vendor 0x8086 product 0x2660 (rev. 0x03)
ppb1: PCI Express 1.0 <Root Port of PCI-E Root Complex>
pci2 at ppb1 bus 5
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
ppb2 at pci0 dev 28 function 1: vendor 0x8086 product 0x2662 (rev. 0x03)
ppb2: PCI Express 1.0 <Root Port of PCI-E Root Complex>
pci3 at ppb2 bus 4
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
ppb3 at pci0 dev 28 function 2: vendor 0x8086 product 0x2664 (rev. 0x03)
ppb3: PCI Express 1.0 <Root Port of PCI-E Root Complex>
pci4 at ppb3 bus 3
pci4: i/o space, memory space enabled, rd/line, wr/inv ok
ppb4 at pci0 dev 28 function 3: vendor 0x8086 product 0x2666 (rev. 0x03)
ppb4: PCI Express 1.0 <Root Port of PCI-E Root Complex>
pci5 at ppb4 bus 2
pci5: i/o space, memory space enabled, rd/line, wr/inv ok
uhci0 at pci0 dev 29 function 0: vendor 0x8086 product 0x2658 (rev. 0x03)
uhci0: interrupting at ioapic0 pin 23
usb0 at uhci0: USB revision 1.0
uhci1 at pci0 dev 29 function 1: vendor 0x8086 product 0x2659 (rev. 0x03)
uhci1: interrupting at ioapic0 pin 19
usb1 at uhci1: USB revision 1.0
uhci2 at pci0 dev 29 function 2: vendor 0x8086 product 0x265a (rev. 0x03)
uhci2: interrupting at ioapic0 pin 18
usb2 at uhci2: USB revision 1.0
uhci3 at pci0 dev 29 function 3: vendor 0x8086 product 0x265b (rev. 0x03)
uhci3: interrupting at ioapic0 pin 16
usb3 at uhci3: USB revision 1.0
ehci0 at pci0 dev 29 function 7: vendor 0x8086 product 0x265c (rev. 0x03)
ehci0: interrupting at ioapic0 pin 23
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2 uhci3
usb4 at ehci0: USB revision 2.0
ppb5 at pci0 dev 30 function 0: vendor 0x8086 product 0x244e (rev. 0xd3)
pci6 at ppb5 bus 6
pci6: i/o space, memory space enabled
fxp0 at pci6 dev 8 function 0: Intel i82801FB LAN Controller (rev. 0x01)
fxp0: interrupting at ioapic0 pin 20
fxp0: Ethernet address 00:13:20:4f:fa:f3
inphy0 at fxp0 phy 1: i82562ET 10/100 media interface, rev. 0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ichlpcib0 at pci0 dev 31 function 0: vendor 0x8086 product 0x2640 (rev. 0x03)
timecounter: Timecounter "ichlpcib0" frequency 3579545 Hz quality 1000
ichlpcib0: 24-bit timer
ichlpcib0: TCO (watchdog) timer configured.
gpio0 at ichlpcib0: 64 pins
piixide0 at pci0 dev 31 function 1: Intel 82801FB IDE Controller
(ICH6) (rev. 0x03)
piixide0: bus-master DMA support present
piixide0: primary channel configured to compatibility mode
piixide0: primary channel interrupting at ioapic0 pin 14
atabus0 at piixide0 channel 0
piixide0: secondary channel configured to compatibility mode
piixide0: secondary channel interrupting at ioapic0 pin 15
atabus1 at piixide0 channel 1
piixide1 at pci0 dev 31 function 2: Intel 82801FB Serial ATA/Raid
Controller (rev. 0x03)
piixide1: bus-master DMA support present
piixide1: primary channel configured to native-PCI mode
piixide1: using ioapic0 pin 19 for native-PCI interrupt
atabus2 at piixide1 channel 0
piixide1: secondary channel configured to native-PCI mode
atabus3 at piixide1 channel 1
ichsmb0 at pci0 dev 31 function 3: vendor 0x8086 product 0x266a (rev. 0x03)
ichsmb0: interrupting at ioapic0 pin 19
iic0 at ichsmb0: I2C bus
isa0 at ichlpcib0
lpt0 at isa0 port 0x378-0x37b irq 7
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com0: console
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
acpicpu0 at cpu0: ACPI CPU
acpicpu0: C1: HLT, lat   0 us, pow     0 mW
acpicpu0: T0: I/O, lat   1 us, pow     0 mW, 100 %
acpicpu0: T1: I/O, lat   1 us, pow     0 mW,  88 %
acpicpu0: T2: I/O, lat   1 us, pow     0 mW,  76 %
acpicpu0: T3: I/O, lat   1 us, pow     0 mW,  64 %
acpicpu0: T4: I/O, lat   1 us, pow     0 mW,  52 %
acpicpu0: T5: I/O, lat   1 us, pow     0 mW,  40 %
acpicpu0: T6: I/O, lat   1 us, pow     0 mW,  28 %
acpicpu0: T7: I/O, lat   1 us, pow     0 mW,  16 %
acpicpu1 at cpu1: ACPI CPU
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "TSC" frequency 3000187420 Hz quality 3000
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
uhub0 at usb0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
atapibus0 at atabus0: 2 targets
uhub1 at usb1: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhub3 at usb3: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
uhub4 at usb4: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
cd0 at atapibus0 drive 0: <SONY DVD-ROM DDU1615, , FYS2> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
cd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
wd0 at atabus3 drive 0
wd0: <ST3250318AS>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 232 GB, 484518 cyl, 16 head, 63 sec, 512 bytes/sect x 488395055 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(piixide1:1:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
crypto: assign driver 0, flags 2
crypto: driver 0 registers alg 1 flags 0 maxoplen 0
crypto: driver 0 registers alg 2 flags 0 maxoplen 0
crypto: driver 0 registers alg 3 flags 0 maxoplen 0
crypto: driver 0 registers alg 4 flags 0 maxoplen 0
crypto: driver 0 registers alg 5 flags 0 maxoplen 0
crypto: driver 0 registers alg 26 flags 0 maxoplen 0
crypto: driver 0 registers alg 27 flags 0 maxoplen 0
crypto: driver 0 registers alg 29 flags 0 maxoplen 0
crypto: driver 0 registers alg 33 flags 0 maxoplen 0
crypto: driver 0 registers alg 17 flags 0 maxoplen 0
crypto: driver 0 registers alg 6 flags 0 maxoplen 0
crypto: driver 0 registers alg 19 flags 0 maxoplen 0
crypto: driver 0 registers alg 7 flags 0 maxoplen 0
crypto: driver 0 registers alg 20 flags 0 maxoplen 0
crypto: driver 0 registers alg 15 flags 0 maxoplen 0
crypto: driver 0 registers alg 24 flags 0 maxoplen 0
crypto: driver 0 registers alg 25 flags 0 maxoplen 0
crypto: driver 0 registers alg 8 flags 0 maxoplen 0
crypto: driver 0 registers alg 21 flags 0 maxoplen 0
crypto: driver 0 registers alg 16 flags 0 maxoplen 0
crypto: driver 0 registers alg 9 flags 0 maxoplen 0
crypto: driver 0 registers alg 10 flags 0 maxoplen 0
crypto: driver 0 registers alg 13 flags 0 maxoplen 0
crypto: driver 0 registers alg 14 flags 0 maxoplen 0
crypto: driver 0 registers alg 28 flags 0 maxoplen 0
crypto: driver 0 registers alg 30 flags 0 maxoplen 0
crypto: driver 0 registers alg 31 flags 0 maxoplen 0
crypto: driver 0 registers alg 32 flags 0 maxoplen 0
crypto: driver 0 registers alg 11 flags 0 maxoplen 0
crypto: driver 0 registers alg 18 flags 0 maxoplen 0
crypto: driver 0 registers alg 23 flags 0 maxoplen 0
crypto: driver 0 registers alg 22 flags 0 maxoplen 0
Kernelized RAIDframe activated
boot device: cd0
root on cd0a dumps on cd0b
vfs_mountroot: can't open root device
cannot mount root, error = 6
root device (default cd0a): cd0d
dump device (default cd0b):
file system (default generic):
root on cd0d dumps on cd0b
root file system type: cd9660
warning: no /dev/console
init path (default /sbin/init):
init: trying /sbin/init
Created tmpfs /dev (1540096 byte, 2976 inodes)


You are using a serial console, we do not know your terminal emulation.
Please select one, typical values are:

        vt100
        ansi
        xterm

Terminal type (just hit ENTER for 'vt220'):      <-  ENTER was typed here

 NetBSD/i386 6.0_BETA

 This menu-driven tool is designed to help you install NetBSD to a hard disk,
 or upgrade an existing NetBSD system, with a minimum of work.  In the
 following menus type the reference letter (a, b, c, ...) to select an item,
 or type CTRL+N/CTRL+P to select the next/previous item.  The arrow keys and
 Page-up/Page-down may also work.  Activate the current selection from the
 menu by typing the enter key.



                +---------------------------------------------+
                ¦>a: Installation messages in English         ¦
                ¦ b: Installation auf Deutsch                 ¦
                ¦ c: Mensajes de instalacion en castellano    ¦
                ¦ d: Messages d'installation en francais      ¦
                ¦ e: Komunikaty instalacyjne w jezyku polskim ¦
                +---------------------------------------------+

References:
- 6.0_BETA boot doesn't complete
  - From: Ray Phillips
- Re: 6.0_BETA boot doesn't complete
  - From: Martin Husemann
- Re: 6.0_BETA boot doesn't complete
  - From: Ray Phillips
- Re: 6.0_BETA boot doesn't complete
  - From: Martin Husemann
- Re: 6.0_BETA boot doesn't complete
  - From: Manuel Bouyer

Prev by Date: Re: 6.0_BETA boot doesn't complete
Next by Date: 6.0_BETA Booting from GPT Partition
Previous by Thread: Re: 6.0_BETA boot doesn't complete
Next by Thread: Re: 6.0_BETA boot doesn't complete
Indexes:

Home | Main Index | Thread Index | Old Index