Re: Banana pi pro no video

[Jason Thorpe <thorpej%me.com@localhost>]

> On Jun 20, 2019, at 3:03 PM, Ron Georgia <netverbs%gmail.com@localhost> wrote:
> 
> I do not see that in sysutils.
> $ /u/p/sysutils> ls | grep banana
> u-boot-bananapi
> u-boot-bananapi-m3
> u-boot-bananapi-r2
> 
> rgeorgia@clement /u/pkgsrc> sudo find . -type f | grep bananapro
> not found

Your pkgsrc may be out of date; I added it on May 29:

revision 1.1
date: 2019-05-29 03:24:02 +0000;  author: thorpej;  state: Exp;  commitid: Bt9LqdFk6D5U53pB;
Add a U-Boot package for the LeMaker Banana Pro.


> 
> On 6/20/19, 8:47 AM, "Jared McNeill" <jmcneill%invisible.ca@localhost> wrote:
> 
>    You cannot use U-boot for a different board and expect anything to work. 
>    Have you tried sysutils/u-boot-bananapro ?
> 
>    On Tue, 18 Jun 2019, Ron Georgia wrote:
> 
>> I am trying to install NetBSD on a Banana pi pro. I downloaded armv7 from http://nycdn.netbsd.org/pub/NetBSD-daily/HEAD/latest/evbarm-earmv7hf/binary/gzimg/armv7.img.gz
>> 
>> I dd the image to sd0d
>> $ sudo dd if=armv7_HEAD.img of=/dev/rsd0d bs=1m conv=sync
>> 
>> I then tried both bananapi u-boot image from =/usr/pkg/share/u-boot based on the wiki found here: https://wiki.netbsd.org/ports/evbarm/install_using_sysinst/
>> 
>> $ sudo dd if=/usr/pkg/share/u-boot/bananapi/u-boot-sunxi-with-spl.bin of=/dev/rsd0d bs=1k seek=8 conv=sync
>> $ sudo dd if=/usr/pkg/share/u-boot/bananapi-m3/u-boot-sunxi-with-spl.bin of=/dev/rsd0d bs=1k seek=8 conv=sync
>> 
>> Note: the documentation says of=/dev/rld0d bs=1k seek=8 conv=sync. Notice the rld0d not rsd0d. Is that right?
>> 
>> Any help is appreciated.
>> 
>> The boot.cmd does not match what the docs says it should be.
>> I looked at boot.cmd:
>> 
>> if test "${board}" = "am335x" ; then
>> 	setenv kernel netbsd-BEAGLEBONE.ub
>> 	setenv mmcpart 0:1
>> 	setenv bootargs root=ld0a
>> else
>> 	setenv use_efi 1
>> fi
>> 
>> if test "${soc}" = "tegra210" ; then
>> 	# enable PCIe
>> 	pci enum
>> fi
>> 
>> if test "${use_efi}" = "1" ; then
>> 	setenv boot_scripts
>> 	setenv boot_script_dhcp
>> 	run distro_bootcmd
>> else
>> 	fatload mmc ${mmcpart} ${kernel_addr_r} ${kernel}
>> 	bootm ${kernel_addr_r} ${bootargs}
>> fi
>> 
>> ================================ boot.ini ================================
>> ODROIDC-UBOOT-CONFIG
>> 
>> setenv bootargs "awge0.mac-address=${ethaddr}"
>> setenv bootcmd "fatload mmc 0:1 0x21000000 netbsd-GENERIC.ub; fatload mmc 0:1 0x20000000 meson8b-odroidc1.dtb; bootm 0x21000000 - 0x20000000"
>> run bootcmd
>> 
>> ================================ cmdline.txt ================================
>> root=ld0a console=fb
>> #fb=1280x1024		# to select a mode, otherwise try EDID
>> #fb=disable		# to disable fb completely
>> 
>> ================================ Config.txt ================================
>> # Boot options, see https://www.raspberrypi.org/documentation/configuration/config-txt/boot.md
>> kernel_address=0x01000040
>> # UART settings, see https://www.raspberrypi.org/documentation/configuration/uart.md
>> enable_uart=1
>> force_turbo=0
>> 
>> 
>> Ron Georgia
>> “90% of my problems are due to ignorance, the other 10% is because I just don’t know any better.”
>> 
>> 
>> 
>> 
>> 
>> 
> 
> 

-- thorpej