Lamobo R1 (a.k.a. Banana Pi BPI-R1)

To: port-arm <port-arm%netbsd.org@localhost>
Subject: Lamobo R1 (a.k.a. Banana Pi BPI-R1)
From: Jason Thorpe <thorpej%me.com@localhost>
Date: Mon, 3 Jun 2019 20:12:03 -0700
Hey folks... just wanted to post a "successful boot!" on my Banana Pi BPI-R1 (canonically, the Lamobo R1), based on the A20 SoC.

I have a 1TB Crucial SSD connected to the on-board SATA controller.  The board also features a Broadcom 5-port Ethernet switch connected to the Gig-E MDIO (note the 5 "ukphy" instances), as well as an on-board Realtek USB WiFi interface.

[   1.0000000] NetBSD/evbarm (fdt) booting ...
[   1.0000000] [ Kernel symbol table missing! ]
[   1.0000000] Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
[   1.0000000]     2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017,
[   1.0000000]     2018, 2019 The NetBSD Foundation, Inc.  All rights reserved.
[   1.0000000] Copyright (c) 1982, 1986, 1989, 1991, 1993
[   1.0000000]     The Regents of the University of California.  All rights reserved.

[   1.0000000] NetBSD 8.99.42 (GENERIC) #53: Mon Jun  3 19:32:55 PDT 2019
[   1.0000000]  thorpej@BigMac.local:/Volumes/Data0/Users/thorpej/hack/NetBSD/current/netbsd-src/sys/arch/evbarm/compile/GENERIC
[   1.0000000] total memory = 1024 MB
[   1.0000000] avail memory = 1003 MB
[   1.0000000] armfdt0 (root)
[   1.0000000] simplebus0 at armfdt0: Lamobo R1
[   1.0000000] simplebus1 at simplebus0
[   1.0000000] cpus0 at simplebus0
[   1.0000000] simplebus2 at simplebus0
[   1.0000000] simplebus3 at simplebus0
[   1.0000000] cpu0 at cpus0: Cortex-A7 r0p4 (Cortex V7A core)
[   1.0000000] cpu0: DC enabled IC enabled WB enabled LABT branch prediction enabled
[   1.0000000] cpu0: 32KB/32B 2-way L1 VIPT Instruction cache
[   1.0000000] cpu0: 32KB/64B 4-way write-back-locking-C L1 PIPT Data cache
[   1.0000000] cpu0: 256KB/64B 8-way write-through L2 PIPT Unified cache
[   1.0000000] vfp0 at cpu0: NEON MPE (VFP 3.0+), rounding, NaN propagation, denormals
[   1.0000000] cpufreqdt0 at cpu0
[   1.0000000] cpu1 at cpus0
[   1.0000000] cpufreqdt1 at cpu1
[   1.0000000] gic0 at simplebus1: GIC
[   1.0000000] armgic0 at gic0: Generic Interrupt Controller, 160 sources (150 valid)
[   1.0000000] armgic0: 16 Priorities, 128 SPIs, 7 PPIs, 15 SGIs
[   1.0000000] fclock0 at simplebus2: 25000000 Hz fixed clock (mii_phy_tx)
[   1.0000000] fclock1 at simplebus2: 125000000 Hz fixed clock (gmac_int_tx)
[   1.0000000] fclock2 at simplebus2: 24000000 Hz fixed clock (osc24M)
[   1.0000000] fclock3 at simplebus2: 32768 Hz fixed clock (osc32k)
[   1.0000000] gtmr0 at simplebus0: Generic Timer
[   1.0000000] gtmr0: interrupting on GIC irq 27 (virtual)
[   1.0000000] armgtmr0 at gtmr0: ARM Generic Timer (24000 kHz)
[   1.0000060] sun4ia10ccu0 at simplebus1: A20 CCU
[   1.0000060] sunxinmi0 at simplebus1: NMI
[   1.0000060] sunxigmacclk0 at simplebus2: GMAC MII/RGMII clock mux
[   1.0000060] sunxigpio0 at simplebus1: PIO
[   1.0000060] gpio0 at sunxigpio0: 175 pins
[   1.0000060] sunxigpio0: interrupting on GIC irq 60
[   1.0000060] sunxisramc0 at simplebus1: SRAM Controller
[   1.0000060] sunxidebe0 at simplebus1: Display Engine Backend (display-backend@1e60000)
[   1.0000060] sunxidebe1 at simplebus1: Display Engine Backend (display-backend@1e40000)
[   1.0000060] sunxihdmi0 at simplebus1: HDMI 1.3
[   1.0000060] sunxitcon0 at simplebus1: LCD/TV timing controller (lcd-controller@1c0c000)
[   1.0000060] sunxitcon1 at simplebus1: LCD/TV timing controller (lcd-controller@1c0d000)
[   1.0000060] connector0 at simplebus0: HDMI connector
[   1.0000060] sunxisid0 at simplebus1: Security ID EFUSE
[   1.0000060] fregulator0 at simplebus0: vcc3v3
[   1.0000060] fregulator1 at simplebus0: usb0-vbus
[   1.0000060] fregulator2 at simplebus0: usb2-vbus
[   1.0000060] fregulator3 at simplebus0: ahci-5v
[   1.0000060] fregulator4 at simplebus0: gmac-3v3
[   1.0000060] sunxidep0 at simplebus0: can't activate pipeline 0
[   1.0000060] sunxidep0: can't activate pipeline 1
[   1.0000060] fregulator5 at simplebus0: vcc3v0
[   1.0000060] fregulator6 at simplebus0: vcc5v0
[   1.0000060] sunxiusbphy0 at simplebus1: USB PHY
[   1.0000060] sunxitwi0 at simplebus1: Marvell TWSI controller
[   1.0000060] sunxitwi0: interrupting on GIC irq 39
[   1.0000060] iic0 at sunxitwi0: I2C bus
[   1.0000060] axp20x0 at iic0 addr 0x34
[   1.0000060] axp20xreg0 at axp20x0: dcdc2 (vdd-cpu)
[   1.0000060] axp20xreg1 at axp20x0: dcdc3 (vdd-int-dll)
[   1.0000060] sunxits0 at simplebus1: Touch Screen Controller
[   1.0000060] sunxits0: interrupting on GIC irq 61
[   1.0000060] /soc/display-frontend@1e00000 at simplebus1 not configured
[   1.0000060] /soc/display-frontend@1e20000 at simplebus1 not configured
[   1.0000060] sun4idma0 at simplebus1: DMA controller
[   1.0000060] sun4idma0: interrupting on GIC irq 59
[   1.0000060] awge0 at simplebus1: GMAC
[   1.0000060] awge0: interrupting on GIC irq 117
[   1.0000060] awge0: Core version: 00000000
[   1.0000060] awge0: Ethernet address 02:15:06:02:53:78
[   1.0000060] ukphy0 at awge0 phy 0: OUI 0x001be9, model 0x0032, rev. 4
[   1.0000060] ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
[   1.0000060] ukphy1 at awge0 phy 1: OUI 0x001be9, model 0x0032, rev. 4
[   1.0000060] ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
[   1.0000060] ukphy2 at awge0 phy 2: OUI 0x001be9, model 0x0032, rev. 4
[   1.0000060] ukphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
[   1.0000060] ukphy3 at awge0 phy 3: OUI 0x001be9, model 0x0032, rev. 4
[   1.0000060] ukphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
[   1.0000060] ukphy4 at awge0 phy 4: OUI 0x001be9, model 0x0032, rev. 4
[   1.0000060] ukphy4: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
[   1.0000060] /soc/spi@1c05000 at simplebus1 not configured
[   1.0000060] sunximmc0 at simplebus1: SD/MMC controller
[   1.0000060] sunximmc0: interrupting on GIC irq 64
[   1.0000060] motg0 at simplebus1: 'otg' mode not supported
[   1.0000060] ehci0 at simplebus1: EHCI
[   1.0000060] ehci0: interrupting on GIC irq 71
[   1.0000060] ehci0: 1 companion controller, 1 port
[   1.0000060] usb0 at ehci0: USB revision 2.0
[   1.0000060] ohci0 at simplebus1: OHCI
[   1.0000060] ohci0: interrupting on GIC irq 96
[   1.0000060] ohci0: OHCI version 1.0
[   1.0000060] usb1 at ohci0: USB revision 1.0
[   1.0000060] /soc/crypto-engine@1c15000 at simplebus1 not configured
[   1.0000060] ahcisata0 at simplebus1: SATA
[   1.0000060] ahcisata0: interrupting on GIC irq 88
[   1.0000060] ahcisata0: AHCI revision 1.10, 1 port, 32 slots, CAP 0x6f24ff80<CCCS,PSC,SSC,PMD,SAM,ISS=0x6f24ff80=Gen2,SCLO,SAL,SALP,SSS,SSNTF,SNCQ>
[   1.0000060] atabus0 at ahcisata0 channel 0
[   1.0000060] ehci1 at simplebus1: EHCI
[   1.0000060] ehci1: interrupting on GIC irq 72
[   1.0000060] ehci1: 1 companion controller, 1 port
[   1.0000060] usb2 at ehci1: USB revision 2.0
[   1.0000060] sunxiwdt0 at simplebus1: Watchdog
[   1.0000060] sunxiwdt0: default watchdog period is 16 seconds
[   1.0000060] sunxirtc0 at simplebus1: RTC
[   1.0000060] /soc/ir@1c21800 at simplebus1 not configured
[   1.0000060] sunxicodec0 at simplebus1: A10 Audio Codec
[   1.0000060] audio0 at sunxicodec0: full duplex, playback, capture, mmap, independent
[   1.0000060] audio0: slinear_le:16 2ch 48000Hz, blk 40ms for playback
[   1.0000060] audio0: slinear_le:16 2ch 48000Hz, blk 40ms for recording
[   1.0000060] spkr0 at audio0: PC Speaker (synthesized)
[   1.0000060] wsbell at spkr0 not configured
[   1.0000060] com0 at simplebus1: ns16550a, working fifo
[   1.0000060] com0: console
[   1.0000060] com0: interrupting on GIC irq 33
[   1.0000060] com1 at simplebus1: ns16550a, working fifo
[   1.0000060] com1: interrupting on GIC irq 36
[   1.0000060] com2 at simplebus1: ns16550a, working fifo
[   1.0000060] com2: interrupting on GIC irq 52
[   1.0000060] sunxitwi1 at simplebus1: Marvell TWSI controller
[   1.0000060] sunxitwi1: interrupting on GIC irq 41
[   1.0000060] iic1 at sunxitwi1: I2C bus
[   1.0000060] /soc/gpu@1c40000 at simplebus1 not configured
[   1.0000060] psci0 at simplebus0: PSCI 0.1
[   1.0000060] armpmu0 at simplebus0: Performance Monitor Unit
[   1.0000060] gpioleds0 at simplebus0: lamobo_r1:green:usr
[   1.0000060] /soc/video-codec@1c0e000 at simplebus1 not configured
[   1.0000060] sunxitimer0 at simplebus1: Timer
[   1.0000060] /soc/hstimer@1c60000 at simplebus1 not configured
[   1.0000060] cpu1: Cortex-A7 r0p4 (Cortex V7A core)
[   1.0000060] cpu1: DC enabled IC enabled WB enabled LABT branch prediction enabled
[   1.6547367] cpu1: 32KB/32B 2-way L1 VIPT Instruction cache
[   1.6547367] cpu1: 32KB/64B 4-way write-back-locking-C L1 PIPT Data cache
[   1.6647230] cpu1: 256KB/64B 8-way write-through L2 PIPT Unified cache
[   1.6747232] vfp1 at cpu1: NEON MPE (VFP 3.0+), rounding, NaN propagation, denormals
[   1.6847276] sdmmc0 at sunximmc0
[   1.8047319] armpmu0: interrupting on GIC irq 152
[   1.8047319] armpmu0: interrupting on GIC irq 153
[   1.8186468] uhub0 at usb0: NetBSD (0000) EHCI root hub (0000), class 9/0, rev 2.00/1.00, addr 1
[   1.8247356] uhub1 at usb1: NetBSD (0000) OHCI root hub (0000), class 9/0, rev 1.00/1.00, addr 1
[   1.8347358] uhub2 at usb2: NetBSD (0000) EHCI root hub (0000), class 9/0, rev 2.00/1.00, addr 1
[   1.8847452] sdmmc0: SD card status: 4-bit, C10, U1
[   1.8847452] ld0 at sdmmc0: <0x9c:0x534f:USD00:0x10:0x65a5fc2a:0x113>
[   1.8947454] ahcisata0 port 0: device present, speed: 3.0Gb/s
[   1.8947454] ld0: 15080 MB, 7659 cyl, 64 head, 63 sec, 512 bytes/sect x 30883840 sectors
[   1.9096221] ld0: 28065920 trailing sectors not covered by disklabel
[   1.9147545] ld0: 4-bit width, High-Speed/SDR25, 50.000 MHz
[   3.4247902] wd0 at atabus0 drive 0
[   3.4247902] wd0: <CT1000MX500SSD1>
[   3.4247902] wd0: 931 GB, 1938021 cyl, 16 head, 63 sec, 512 bytes/sect x 1953525168 sectors
[   4.0848115] urtwn0 at uhub2 port 1
[   4.0848115] urtwn0: Realtek (0xbda) 802.11n WLAN Adapter (0x8178), rev 2.00/2.00, addr 2
[   4.2148160] urtwn0: MAC/BB RTL8192CU, RF 6052 2T2R, address 10:a4:be:6c:ee:91
[   4.2148160] urtwn0: 1 rx pipe, 2 tx pipes
[   4.2272963] urtwn0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
[   4.2272963] urtwn0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
[   4.2370591] WARNING: 2 errors while detecting hardware; check system log.

-- thorpej
Prev by Date: Re: Cortex-A9 boot problems with d-cache on Zynq
Next by Date: Re: MBR partition table and the "active" flag
Previous by Thread: qt5-qtwebkit on arm
Next by Thread: Pinebook - Emma does not show up
Indexes:
Home | Main Index | Thread Index | Old Index