Re: Several issues on Sheevaplug

[Sylvain Mora <sylvain.mora%googlemail.com@localhost>]

Hi,

This is my current dmesg during boot :

NetBSD 5.99.44 (SHEEVAPLUG_FW) #3: Sun Jan 30 19:45:07 CET 2011
        
solevis@corellia:/Users/solevis/Documents/NetBSD/cvs/src/sys/arch/evbarm/compile/obj/SHEEVAPLUG_FW
total memory = 512 MB
avail memory = 497 MB
timecounter: Timecounters tick every 10.000 msec
mainbus0 (root)
cpu0 at mainbus0: Sheeva 88SV131 rev 1 (ARM9E-S core)
cpu0: DC enabled IC enabled WB enabled EABT branch prediction enabled
cpu0: 16KB/32B 4-way Instruction cache
cpu0: 16KB/32B 4-way write-back-locking-C Data cache
mvsoc0 at mainbus0: Marvell 88F6281 Rev. A0  Kirkwood
mvsoc0: CPU Clock 1200.000 MHz  SysClock 400.000 MHz  TClock 200.000 MHz
mvsoctmr0 at mvsoc0 unit 0 offset 0x20300-0x203ff: Marvell SoC Timer
mvsocgpp at mvsoc0 unit 0 not configured
com0 at mvsoc0 unit 0 offset 0x12000 irq 33: ns16550a, working fifo
com0: console
com1 at mvsoc0 unit 1 offset 0x12100-0x1211f irq 34: ns16550a, working fifo
ehci0 at mvsoc0 unit 0 offset 0x50000-0x51fff irq 19: Marvell USB 2.0 Interface
ehci0: EHCI version 1.0
usb0 at ehci0: USB revision 2.0
gttwsi0 at mvsoc0 unit 0 offset 0x11000-0x11fff irq 29: Marvell TWSI controller
iic0 at gttwsi0: I2C bus
mvcesa at mvsoc0 unit 0 not configured
mvgbec0 at mvsoc0 unit 0 offset 0x70000-0x73fff: Marvell Gigabit Ethernet 
Controller
mvgbe0 at mvgbec0 port 0 irq 11
mvgbe0: Ethernet address 00:50:43:6a:20:2b
makphy0 at mvgbe0 phy 0: Marvell 88E1116R Gigabit PHY, rev. 0
makphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
mvgbec1 at mvsoc0 unit 1 offset 0x74000-0x77fff: Marvell Gigabit Ethernet 
Controller
mvgbe at mvgbec1 port 0 not configured
mvpex at mvsoc0 unit 0 not configured
mvsata at mvsoc0 unit 0 not configured
mvsdio0 at mvsoc0 unit 0 offset 0x90000-0x9ffff irq 28: Marvell Secure Digital 
Input/Output Interface
sdmmc0 at mvsdio0
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "mvsoctmr" frequency 200000000 Hz quality 100
uhub0 at usb0: Marvell EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub0: 1 port with 1 removable, self powered
umass0 at uhub0 port 1 configuration 1 interface 0
umass0: SanDisk Cruzer Micro, rev 2.00/2.00, addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 1 lun per target
sd0 at scsibus0 target 0 lun 0: <SanDisk, Cruzer, 6.01> disk removable
sd0: 3836 MB, 61392 cyl, 4 head, 32 sec, 512 bytes/sect x 7858175 sectors
boot device: <unknown>
root device: sd0a
dump device (default sd0b): 
file system (default generic): ffs
root on sd0a dumps on sd0b
WARNING: no TOD clock present
WARNING: using filesystem time
WARNING: CHECK AND RESET THE DATE!
warning: no /dev/console
init path (default /sbin/init): 
init: copying out path `/sbin/init' 11

Regards,
Sylvain

Le 2 févr. 2011 à 06:24, Andy Ruhl a écrit :

> On Tue, Feb 1, 2011 at 2:10 PM, Solevis <solevis.tux%gmail.com@localhost> 
> wrote:
>> - When I use the serial console for a long time, my Sheevaplug hangs up 
>> (nothing to report with OpenSSH).
>> - I can't reboot correctly, NetBSD terminates all processes and then freezes 
>> at "rebooting..." (same issue with poweroff)
>> - If i have no sdcard in the Sheevaplug, NetBSD floods me with "sdmmc0: 
>> couldn't enable card".
>> 
>> Problems I've encountered might have been my mistakes.
>> Hoping you find a solution. I stay tuned.
> 
> Do you mind posting the dmesg.boot? I tried to find one for a
> Sheevaplug but couldn't find one. I am interested in this device.
> 
> Do you have any files in /var/crash? If so, they might help unless the
> problem was fixed from the solution from the other post.
> 
> Andy