Re: SheevaPlug support?

[Robert Swindells <rjs%fdy2.demon.co.uk@localhost>]

Ron McDowell <rcm%fuzzwad.org@localhost> wrote:
>Hi, is there any support for the Marvel SheevaPlug http://openplug.org/
>ARM box? Thanks.

The mvphy driver needs a bit more work, but this is where I am up to
for today.

Robert Swindells

Marvell>> bootm
## Booting image at 00800000 ...
   Image Name:   NetBSD 5.99.13 (SHEEVAPLUG)    
   Created:      2009-06-17  22:02:41 UTC
   Image Type:   ARM NetBSD Kernel Image (uncompressed)
   Data Size:    3360164 Bytes =  3.2 MB
   Load Address: 00100000
   Entry Point:  00100000
   Verifying Checksum ... OK
OK
## Transferring control to NetBSD stage-2 loader (at address 00100000) ...

NetBSD/evbarm (sheevaplug) booting ...
[ Kernel symbol table missing! ]
Loaded initial symtab at 0xc03b4bf8, strtab at 0xc03de6b0, # entries 10574
pmap_postinit: Allocated 35 static L1 descriptor tables
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.99.13 (SHEEVAPLUG) #40: Wed Jun 17 23:02:37 BST 2009
        rjs%ren.fdy2.net@localhost:/u10/src/sys/arch/evbarm/compile/SHEEVAPLUG
total memory = 512 MB
avail memory = 497 MB
mainbus0 (root)
cpu0 at mainbus0: Sheeva 88SV131 rev 1 (ARM9EJ-S core)
cpu0: DC enabled IC enabled WB enabled EABT branch prediction enabled
cpu0: 16KB/32B 4-way Instruction cache
cpu0: 16KB/32B 4-way write-back-locking-C Data cache
kirkwood0 at mainbus0: Marvell MV88F6281 SoC Rev. A0 Kirkwood1
kirkwood0: CPU Clock 1200.000 MHz  SysClock 400.000 MHz  TClock 200.000 MHz
oriontmr0 at kirkwood0 addr 0xf1020300-0xf10203ff: Marvell Orion Timer
com0 at kirkwood0 addr 0xf1012000-0xf101201f irq 33: ns16550a, working fifo
com0: console
com1 at kirkwood0 addr 0xf1012100-0xf101211f irq 34: ns16550a, working fifo
ehci0 at kirkwood0 addr 0xf1050000-0xf1051fff irq 19: Marvell Orion USB 2.0 Inte
usb0 at ehci0: USB revision 2.0
oriongbe0 at kirkwood0 addr 0xf1072000-0xf1073fff irq 11: Marvell Gigabit Etherr
oriongbe0: Ethernet address 00:50:43:01:c8:8d
OUI 0x000ac2 model 0x0024 rev 0 at oriongbe0 phy 0 not configured
oriongbe0: no PHY found!
oriongbe1 at kirkwood0 addr 0xf1076000-0xf1077fff irq 15: Marvell Gigabit Etherr
oriongbe1: Ethernet address 00:00:00:00:00:00
oriongbe1: no PHY found!
orioncesa0 at kirkwood0 addr 0xf1030000-0xf103ffff irq 28: Marvell Orion Cryptor
oriontwsi0 at kirkwood0 addr 0xf1011000-0xf101101f irq 29: Orion TWSI controller
iic0 at oriontwsi0: I2C bus
uhub0 at usb0: vendor 0x0000 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
boot device: <unknown>
root device: