NetBSD-Bugs archive

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index][Old Index]

port-sgimips/46417: NetBSD 5.1.2 netbsd-INSTALL32_IP2x panics on SGI Challenge S

>Number:         46417
>Category:       port-sgimips
>Synopsis:       NetBSD 5.1.2 netbsd-INSTALL32_IP2x panics on SGI Challenge S
>Confidential:   no
>Severity:       critical
>Priority:       high
>Responsible:    port-sgimips-maintainer
>State:          open
>Class:          sw-bug
>Submitter-Id:   net
>Arrival-Date:   Sun May 06 08:15:01 +0000 2012
>Originator:     Tim McIntosh
>Release:        NetBSD 5.1.2
NetBSD 5.0 NetBSD 5.0 (GENERIC32_IP2x) #0: Mon Apr 27 06:08:08 
UTC 2009

(trying to upgrade to 5.1.2)
Netbooted netbsd-INSTALL32_IP2x over ec0 interface.  Panics on boot:

>> boot
Obtaining .//netbsd-INSTALL32_IP2x from server
Obtaining .//netbsd-INSTALL32_IP2x from server
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010, 2011, 2012
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.1.2 (INSTALL32_IP2x) #0: Thu Feb  2 21:44:03 UTC 2012
total memory = 256 MB
(768 KB reserved for ARCS)
avail memory = 242 MB
mainbus0 (root): SGI-IP22 [SGI, 690b6eec], 1 processor
cpu0 at mainbus0: MIPS R4400 CPU (0x460) Rev. 6.0 with MIPS R4010 FPC Rev. 0.0
cpu0: 16KB/16B direct-mapped L1 Instruction cache, 48 TLB entries
cpu0: 16KB/16B direct-mapped write-back L1 Data cache
cpu0: 1024KB/128B direct-mapped write-back L2 Unified cache
ioc0 at mainbus0 addr 0x1fbd9800: rev 0, machine Indy (Guinness), board rev 0
int0 at mainbus0 addr 0x1fbd9880
int0: bus 100MHz, CPU 200MHz
imc0 at mainbus0 addr 0x1fa00000: revision 3
gio0 at imc0
giopci0 at gio0 slot 1 addr 0x1f400000: Phobos G130 10/100 Ethernet
pci0 at giopci0 bus 0
tlp0 at pci0 dev 0 function 0: DECchip 21143 Ethernet, pass 4.1
tlp0: interrupting at slot EXP0
tlp0: Ethernet address 00:60:f5:08:5d:9f
lxtphy0 at tlp0 phy 1: LXT970 10/100 media interface, rev. 3
lxtphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
hpc0 at gio0 addr 0x1fb80000: SGI HPC3 (onboard)
zsc0 at hpc0 offset 0x59830
zstty0 at zsc0 channel 1 (console i/o)
zstty1 at zsc0 channel 0
pckbc0 at hpc0 offset 0x59840
sq0 at hpc0 offset 0x54000: SGI Seeq 80c03
sq0: Ethernet address 08:00:69:0b:6e:ec
wdsc0 at hpc0 offset 0x44000: WD33C93B (20.0 MHz clock, BURST DMA, SCSI ID 0)
wdsc0: microcode revision 0x0d, Fast SCSI
scsibus0 at wdsc0: 8 targets, 8 luns per target
dsclock0 at hpc0 offset 0x60000
pi1ppc0 at hpc0 offset 0x58000
pi1ppc0: capabilities=8<PS2>
ppbus0 at pi1ppc0
ppbus0: No IEEE1284 device found.
panel0 at hpc0 offset 0x59800
panic: invalid interrupt level
Stopped in pid 0.1 (system) at  0x882dc254:     jr      ra
                bdslot: nop
Boot the netbsd-INSTALL32_IP2x kernel via bootp/tftp.
Last line before panic was:

panel0 at hpc0 offset 0x59800

I'm suspect this might be caused by the new driver for the Indy front panel 
buttons (the Challenge S has no connection to the front panel buttons):

sys/arch/sgimips/hpc/panel.c                    1.1

        Add a driver for the Indy's front panel buttons.
        - power button presses are reported to sysmon
        - volume control buttons are reported to PMF
        [macallan, ticket #976]

Home | Main Index | Thread Index | Old Index