tech-x11 archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index][Old Index]
nouveau problem (amd64/8.99.42)
Hi!
On a machine with a Geforce GTX 960 (which I was told is supported), X
doesn't start (startx doesn't succeed, see attached log).
The nouveau lines in dmesg don't look very good... (see attached dmesg).
X -configure doesn't recognize the nouveau driver.
Additionally, it lists all drivers twice!?
kernel config is quite simple:
--- begin quote ---
include "arch/amd64/conf/GENERIC"
# Kernel Address Sanitizer
makeoptions KASAN=1
options KASAN
no options SVS
options FONT_GO_MONO12x23
no options FONT_BOLD16x32
no options FONT_BOLD8x16
no nvme*
--- end quote ---
Any ideas?
Thanks,
Thomas
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017,
2018, 2019 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 8.99.42 (HOSTNAME) #0: Fri May 31 17:53:20 CEST 2019
wiz%hostname.at@localhost:/usr/obj/sys/arch/amd64/compile/HOSTNAME
total memory = 127 GB
avail memory = 112 GB
pool redzone disabled for 'buf64k'
cpu_rng: RDSEED
rnd: seeded with 128 bits
timecounter: Timecounters tick every 10.000 msec
Kernelized RAIDframe activated
running cgd selftest aes-xts-256 aes-xts-512 done
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
To Be Filled By O.E.M. To Be Filled By O.E.M. (To Be Filled By O.E.M.)
mainbus0 (root)
ACPI: RSDP 0x00000000000F05B0 000024 (v02 AMD )
ACPI: XSDT 0x0000000078D110A0 0000BC (v01 AMD A M I 03242016 AMI 00010013)
ACPI: FACP 0x0000000078D1C270 000114 (v06 AMD A M I 03242016 AMI 00010013)
ACPI: DSDT 0x0000000078D111F0 00B07B (v02 AMD A M I 03242016 INTL 20120913)
ACPI: FACS 0x0000000079124700 000040
ACPI: APIC 0x0000000078D1C388 00046A (v03 AMD A M I 03242016 AMI 00010013)
ACPI: FPDT 0x0000000078D1C7F8 000044 (v01 AMD A M I 03242016 AMI 00010013)
ACPI: FIDT 0x0000000078D1C840 00009C (v01 AMD A M I 03242016 AMI 00010013)
ACPI: SSDT 0x0000000078D1C8E0 008C4C (v02 AMD AMD ALIB 00000002 MSFT 04000000)
ACPI: SSDT 0x0000000078D25530 0001CC (v02 AMD CPUSSDT 03242016 AMI 03242016)
ACPI: SSDT 0x0000000078D25700 002CFA (v01 AMD AMD AOD 00000001 INTL 20120913)
ACPI: MCFG 0x0000000078D28400 00003C (v01 AMD A M I 03242016 MSFT 00010013)
ACPI: AAFT 0x0000000078D28440 000440 (v01 AMD OEMAAFT 03242016 MSFT 00000097)
ACPI: SSDT 0x0000000078D28880 004604 (v01 AMD AMD CPU 00000001 AMD 00000001)
ACPI: CRAT 0x0000000078D2CE88 001DF8 (v01 AMD AMD CRAT 00000001 AMD 00000001)
ACPI: CDIT 0x0000000078D2EC80 000029 (v01 AMD AMD CDIT 00000001 AMD 00000001)
ACPI: HPET 0x0000000078D2ECB0 000038 (v01 AMD A M I 03242016 AMI 00000005)
ACPI: SSDT 0x0000000078D2ECE8 000024 (v01 AMDFCH FCHZP 00001000 INTL 20120913)
ACPI: UEFI 0x0000000078D2ED10 000048 (v01 AMD A M I 00000002 01000013)
ACPI: IVRS 0x0000000078D2ED58 000130 (v02 AMD AMD IVRS 00000001 AMD 00000000)
ACPI: SSDT 0x0000000078D2EE88 001A41 (v01 AMD AmdTable 00000001 INTL 20120913)
ACPI: SSDT 0x0000000078D308D0 0000F8 (v01 AMD AMD PT 00001000 INTL 20120913)
ACPI: WSMT 0x0000000078D309C8 000028 (v01 AMD A M I 03242016 AMI 00010013)
ACPI: 8 ACPI AML tables successfully acquired and loaded
ioapic0 at mainbus0 apid 128: pa 0xfec00000, version 0x21, 24 pins
ioapic0: autoconfiguration error: can't remap to apid 128
ioapic1 at mainbus0 apid 129: pa 0xefc00000, version 0x21, 32 pins
ioapic1: autoconfiguration error: can't remap to apid 129
ioapic2 at mainbus0 apid 130: pa 0xb7a00000, version 0x21, 32 pins
ioapic2: autoconfiguration error: can't remap to apid 130
cpu0 at mainbus0 apid 0
cpu0: AMD Ryzen Threadripper 2950X 16-Core Processor , id 0x800f82
cpu0: package 0, core 0, smt 0
cpu1 at mainbus0 apid 2
cpu1: AMD Ryzen Threadripper 2950X 16-Core Processor , id 0x800f82
cpu1: package 0, core 1, smt 0
cpu2 at mainbus0 apid 4
cpu2: AMD Ryzen Threadripper 2950X 16-Core Processor , id 0x800f82
cpu2: package 0, core 2, smt 0
cpu3 at mainbus0 apid 6
cpu3: AMD Ryzen Threadripper 2950X 16-Core Processor , id 0x800f82
cpu3: package 0, core 3, smt 0
cpu4 at mainbus0 apid 8
cpu4: AMD Ryzen Threadripper 2950X 16-Core Processor , id 0x800f82
cpu4: package 0, core 4, smt 0
cpu5 at mainbus0 apid 10
cpu5: AMD Ryzen Threadripper 2950X 16-Core Processor , id 0x800f82
cpu5: package 0, core 5, smt 0
cpu6 at mainbus0 apid 12
cpu6: AMD Ryzen Threadripper 2950X 16-Core Processor , id 0x800f82
cpu6: package 0, core 6, smt 0
cpu7 at mainbus0 apid 14
cpu7: AMD Ryzen Threadripper 2950X 16-Core Processor , id 0x800f82
cpu7: package 0, core 7, smt 0
cpu8 at mainbus0 apid 16
cpu8: AMD Ryzen Threadripper 2950X 16-Core Processor , id 0x800f82
cpu8: package 0, core 8, smt 0
cpu9 at mainbus0 apid 18
cpu9: AMD Ryzen Threadripper 2950X 16-Core Processor , id 0x800f82
cpu9: package 0, core 9, smt 0
cpu10 at mainbus0 apid 20
cpu10: AMD Ryzen Threadripper 2950X 16-Core Processor , id 0x800f82
cpu10: package 0, core 10, smt 0
cpu11 at mainbus0 apid 22
cpu11: AMD Ryzen Threadripper 2950X 16-Core Processor , id 0x800f82
cpu11: package 0, core 11, smt 0
cpu12 at mainbus0 apid 24
cpu12: AMD Ryzen Threadripper 2950X 16-Core Processor , id 0x800f82
cpu12: package 0, core 12, smt 0
cpu13 at mainbus0 apid 26
cpu13: AMD Ryzen Threadripper 2950X 16-Core Processor , id 0x800f82
cpu13: package 0, core 13, smt 0
cpu14 at mainbus0 apid 28
cpu14: AMD Ryzen Threadripper 2950X 16-Core Processor , id 0x800f82
cpu14: package 0, core 14, smt 0
cpu15 at mainbus0 apid 30
cpu15: AMD Ryzen Threadripper 2950X 16-Core Processor , id 0x800f82
cpu15: package 0, core 15, smt 0
cpu16 at mainbus0 apid 1
cpu16: AMD Ryzen Threadripper 2950X 16-Core Processor , id 0x800f82
cpu16: package 0, core 0, smt 1
cpu17 at mainbus0 apid 3
cpu17: AMD Ryzen Threadripper 2950X 16-Core Processor , id 0x800f82
cpu17: package 0, core 1, smt 1
cpu18 at mainbus0 apid 5
cpu18: AMD Ryzen Threadripper 2950X 16-Core Processor , id 0x800f82
cpu18: package 0, core 2, smt 1
cpu19 at mainbus0 apid 7
cpu19: AMD Ryzen Threadripper 2950X 16-Core Processor , id 0x800f82
cpu19: package 0, core 3, smt 1
cpu20 at mainbus0 apid 9
cpu20: AMD Ryzen Threadripper 2950X 16-Core Processor , id 0x800f82
cpu20: package 0, core 4, smt 1
cpu21 at mainbus0 apid 11
cpu21: AMD Ryzen Threadripper 2950X 16-Core Processor , id 0x800f82
cpu21: package 0, core 5, smt 1
cpu22 at mainbus0 apid 13
cpu22: AMD Ryzen Threadripper 2950X 16-Core Processor , id 0x800f82
cpu22: package 0, core 6, smt 1
cpu23 at mainbus0 apid 15
cpu23: AMD Ryzen Threadripper 2950X 16-Core Processor , id 0x800f82
cpu23: package 0, core 7, smt 1
cpu24 at mainbus0 apid 17
cpu24: AMD Ryzen Threadripper 2950X 16-Core Processor , id 0x800f82
cpu24: package 0, core 8, smt 1
cpu25 at mainbus0 apid 19
cpu25: AMD Ryzen Threadripper 2950X 16-Core Processor , id 0x800f82
cpu25: package 0, core 9, smt 1
cpu26 at mainbus0 apid 21
cpu26: AMD Ryzen Threadripper 2950X 16-Core Processor , id 0x800f82
cpu26: package 0, core 10, smt 1
cpu27 at mainbus0 apid 23
cpu27: AMD Ryzen Threadripper 2950X 16-Core Processor , id 0x800f82
cpu27: package 0, core 11, smt 1
cpu28 at mainbus0 apid 25
cpu28: AMD Ryzen Threadripper 2950X 16-Core Processor , id 0x800f82
cpu28: package 0, core 12, smt 1
cpu29 at mainbus0 apid 27
cpu29: AMD Ryzen Threadripper 2950X 16-Core Processor , id 0x800f82
cpu29: package 0, core 13, smt 1
cpu30 at mainbus0 apid 29
cpu30: AMD Ryzen Threadripper 2950X 16-Core Processor , id 0x800f82
cpu30: package 0, core 14, smt 1
cpu31 at mainbus0 apid 31
cpu31: AMD Ryzen Threadripper 2950X 16-Core Processor , id 0x800f82
cpu31: package 0, core 15, smt 1
acpi0 at mainbus0: Intel ACPICA 20190405
acpi0: X/RSDT: OemId < AMD, A M I ,03242016>, AslId <AMI ,00010013>
acpi0: MCFG: segment 0, bus 0-127, address 0x00000000f0000000
acpi0: SCI interrupting at int 9
acpi0: fixed power button present
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
hpet0 at acpi0: high precision event timer (mem 0xfed00000-0xfed00400)
timecounter: Timecounter "hpet0" frequency 14318180 Hz quality 2000
AMDN (PNP0C01) at acpi0 not configured
APSP (PNP0C02) at acpi0 not configured
UMEM (PNP0C02) at acpi0 not configured
attimer1 at acpi0 (TMR, PNP0100): io 0x40-0x43 irq 0
pcppi1 at acpi0 (SPKR, PNP0800): io 0x61
spkr0 at pcppi1: PC Speaker
wsbell at spkr0 not configured
midi0 at pcppi1: PC speaker
sysbeep0 at pcppi1
SIO1 (PNP0C02) at acpi0 not configured
S900 (PNP0C02) at acpi0 not configured
acpiwmi0 at acpi0 (WMI1, PNP0C14-MXM2): ACPI WMI Interface
acpiwmibus at acpiwmi0 not configured
UMEM (PNP0C02) at acpi0 not configured
acpibut0 at acpi0 (PWRB, PNP0C0C-170): ACPI Power Button
GPIO (AMDI0030) at acpi0 not configured
I2CA (AMDI0010) at acpi0 not configured
AWR0 (PNP0C02) at acpi0 not configured
ABR0 (PNP0C02) at acpi0 not configured
ABR1 (PNP0C02) at acpi0 not configured
ABR2 (PNP0C02) at acpi0 not configured
ABR3 (PNP0C02) at acpi0 not configured
ABR4 (PNP0C02) at acpi0 not configured
ABR5 (PNP0C02) at acpi0 not configured
ABR6 (PNP0C02) at acpi0 not configured
ABR7 (PNP0C02) at acpi0 not configured
AWR1 (PNP0C02) at acpi0 not configured
ABR8 (PNP0C02) at acpi0 not configured
ABR9 (PNP0C02) at acpi0 not configured
ABRA (PNP0C02) at acpi0 not configured
ABRB (PNP0C02) at acpi0 not configured
ABRC (PNP0C02) at acpi0 not configured
ABRD (PNP0C02) at acpi0 not configured
ABRE (PNP0C02) at acpi0 not configured
ABRF (PNP0C02) at acpi0 not configured
PTIO (AMDIF030) at acpi0 not configured
acpiwmi1 at acpi0 (AOD, PNP0C14-AOD): ACPI WMI Interface
acpiwmibus at acpiwmi1 not configured
attimer1: attached to pcppi1
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
amdsmn0 at pci0 dev 0 function 0: AMD Family 17h System Management Network
amdzentemp0 at amdsmn0: AMD CPU Temperature Sensors (Family17h)
vendor 1022 product 1451 (IOMMU system) at pci0 dev 0 function 2 not configured
pchb0 at pci0 dev 1 function 0: vendor 1022 product 1452 (rev. 0x00)
ppb0 at pci0 dev 1 function 1: vendor 1022 product 1453 (rev. 0x00)
ppb0: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x4 @ 8.0GT/s
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
xhci0 at pci1 dev 0 function 0: vendor 1022 product 43ba (rev. 0x02)
xhci0: interrupting at msix0 vec 0
xhci0: xHCI version 1.10
usb0 at xhci0: USB revision 3.1
usb1 at xhci0: USB revision 2.0
ahcisata0 at pci1 dev 0 function 1: vendor 1022 product 43b6 (rev. 0x02)
ahcisata0: 64-bit DMA
ahcisata0: AHCI revision 1.31, 8 ports, 32 slots, CAP 0xef36ff27<SXS,PSC,SSC,PMD,SPM,SAM,ISS=0x3=Gen3,SCLO,SAL,SALP,SSS,SSNTF,SNCQ,S64A>
ahcisata0: interrupting at msi1 vec 0
atabus0 at ahcisata0 channel 0
atabus1 at ahcisata0 channel 1
atabus2 at ahcisata0 channel 2
atabus3 at ahcisata0 channel 3
atabus4 at ahcisata0 channel 4
atabus5 at ahcisata0 channel 5
atabus6 at ahcisata0 channel 6
atabus7 at ahcisata0 channel 7
ppb1 at pci1 dev 0 function 2: vendor 1022 product 43b1 (rev. 0x02)
ppb1: PCI Express capability version 2 <Upstream Port of PCI-E Switch>
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
ppb2 at pci2 dev 0 function 0: vendor 1022 product 43b4 (rev. 0x02)
ppb2: PCI Express capability version 2 <Downstream Port of PCI-E Switch> x4 @ 5.0GT/s
pci3 at ppb2 bus 3
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
ppb3 at pci2 dev 4 function 0: vendor 1022 product 43b4 (rev. 0x02)
ppb3: PCI Express capability version 2 <Downstream Port of PCI-E Switch> x1 @ 5.0GT/s
ppb3: link is x1 @ 2.5GT/s
pci4 at ppb3 bus 4
pci4: i/o space, memory space enabled, rd/line, wr/inv ok
wm0 at pci4 dev 0 function 0: I211 Ethernet (COPPER) (rev. 0x03)
wm0: for TX and RX interrupting at msix2 vec 0 affinity to 1
wm0: for TX and RX interrupting at msix2 vec 1 affinity to 2
wm0: for LINK interrupting at msix2 vec 2
wm0: PCI-Express bus
wm0: 64 words iNVM, version 0.4
wm0: Ethernet address 70:85:c2:b5:61:26
wm0: Copper
wm0: 0xc614420<INVM,IOH_VALID,PCIE,NEWQUEUE,WOL,EEE,PLLWA,CLSEMWA>
makphy0 at wm0 phy 1: I210 10/100/1000 media interface, rev. 0
makphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
ppb4 at pci2 dev 5 function 0: vendor 1022 product 43b4 (rev. 0x02)
ppb4: PCI Express capability version 2 <Downstream Port of PCI-E Switch> x1 @ 5.0GT/s
pci5 at ppb4 bus 5
pci5: i/o space, memory space enabled, rd/line, wr/inv ok
ppb5 at pci2 dev 6 function 0: vendor 1022 product 43b4 (rev. 0x02)
ppb5: PCI Express capability version 2 <Downstream Port of PCI-E Switch> x1 @ 5.0GT/s
pci6 at ppb5 bus 6
pci6: i/o space, memory space enabled, rd/line, wr/inv ok
vendor 10ec product 8125 (ethernet network, revision 0x01) at pci6 dev 0 function 0 not configured
ppb6 at pci2 dev 7 function 0: vendor 1022 product 43b4 (rev. 0x02)
ppb6: PCI Express capability version 2 <Downstream Port of PCI-E Switch> x1 @ 5.0GT/s
pci7 at ppb6 bus 7
pci7: i/o space, memory space enabled, rd/line, wr/inv ok
ppb7 at pci0 dev 1 function 4: vendor 1022 product 1453 (rev. 0x00)
ppb7: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x4 @ 8.0GT/s
pci8 at ppb7 bus 8
pci8: i/o space, memory space enabled, rd/line, wr/inv ok
vendor 144d product a808 (Flash mass storage, NVMe) at pci8 dev 0 function 0 not configured
pchb1 at pci0 dev 2 function 0: vendor 1022 product 1452 (rev. 0x00)
pchb2 at pci0 dev 3 function 0: vendor 1022 product 1452 (rev. 0x00)
pchb3 at pci0 dev 4 function 0: vendor 1022 product 1452 (rev. 0x00)
pchb4 at pci0 dev 7 function 0: vendor 1022 product 1452 (rev. 0x00)
ppb8 at pci0 dev 7 function 1: vendor 1022 product 1454 (rev. 0x00)
ppb8: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x16 @ 8.0GT/s
pci9 at ppb8 bus 9
pci9: i/o space, memory space enabled, rd/line, wr/inv ok
vendor 1022 product 145a (non-essential instrumentation, subclass 0x00) at pci9 dev 0 function 0 not configured
vendor 1022 product 1456 (miscellaneous crypto) at pci9 dev 0 function 2 not configured
xhci1 at pci9 dev 0 function 3: vendor 1022 product 145f (rev. 0x00)
xhci1: interrupting at msix3 vec 0
xhci1: xHCI version 1.0
usb2 at xhci1: USB revision 3.0
usb3 at xhci1: USB revision 2.0
pchb5 at pci0 dev 8 function 0: vendor 1022 product 1452 (rev. 0x00)
ppb9 at pci0 dev 8 function 1: vendor 1022 product 1454 (rev. 0x00)
ppb9: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x16 @ 8.0GT/s
pci10 at ppb9 bus 10
pci10: i/o space, memory space enabled, rd/line, wr/inv ok
vendor 1022 product 1455 (non-essential instrumentation, subclass 0x00) at pci10 dev 0 function 0 not configured
ahcisata1 at pci10 dev 0 function 2: vendor 1022 product 7901 (rev. 0x51)
ahcisata1: 64-bit DMA
ahcisata1: AHCI revision 1.31, 1 port, 32 slots, CAP 0xf737ff00<PSC,SSC,PMD,FBSS,SPM,SAM,ISS=0x3=Gen3,SCLO,SAL,SALP,SMPS,SSNTF,SNCQ,S64A>
ahcisata1: interrupting at msi4 vec 0
atabus8 at ahcisata1 channel 0
hdaudio0 at pci10 dev 0 function 3: HD Audio Controller
hdaudio0: interrupting at msi5 vec 0
hdafg0 at hdaudio0: vendor 10ec product 1220
hdafg0: DAC00 6ch: Speaker [Jack]
hdafg0: DAC01 2ch: HP Out [Jack]
hdafg0: DIG02 2ch: SPDIF Out [Jack]
hdafg0: ADC03 2ch: Line In [Jack], Mic In [Jack]
hdafg0: ADC04 2ch: Mic In [Jack]
hdafg0: 6ch/2ch 32000Hz 44100Hz 48000Hz 88200Hz 96000Hz 192000Hz PCM16 PCM20 PCM24 AC3
audio0 at hdafg0: full duplex, playback, capture, mmap, independent
audio0: slinear_le:16 6ch 48000Hz, blk 40ms for playback
audio0: slinear_le:16 2ch 48000Hz, blk 40ms for recording
spkr1 at audio0: PC Speaker (synthesized)
wsbell at spkr1 not configured
vendor 1022 product 790b (SMBus serial bus, revision 0x59) at pci0 dev 20 function 0 not configured
pcib0 at pci0 dev 20 function 3: vendor 1022 product 790e (rev. 0x51)
pchb6 at pci0 dev 24 function 0: vendor 1022 product 1460 (rev. 0x00)
pchb7 at pci0 dev 24 function 1: vendor 1022 product 1461 (rev. 0x00)
pchb8 at pci0 dev 24 function 2: vendor 1022 product 1462 (rev. 0x00)
pchb9 at pci0 dev 24 function 3: vendor 1022 product 1463 (rev. 0x00)
pchb10 at pci0 dev 24 function 4: vendor 1022 product 1464 (rev. 0x00)
pchb11 at pci0 dev 24 function 5: vendor 1022 product 1465 (rev. 0x00)
pchb12 at pci0 dev 24 function 6: vendor 1022 product 1466 (rev. 0x00)
pchb13 at pci0 dev 24 function 7: vendor 1022 product 1467 (rev. 0x00)
pchb14 at pci0 dev 25 function 0: vendor 1022 product 1460 (rev. 0x00)
pchb15 at pci0 dev 25 function 1: vendor 1022 product 1461 (rev. 0x00)
pchb16 at pci0 dev 25 function 2: vendor 1022 product 1462 (rev. 0x00)
pchb17 at pci0 dev 25 function 3: vendor 1022 product 1463 (rev. 0x00)
pchb18 at pci0 dev 25 function 4: vendor 1022 product 1464 (rev. 0x00)
pchb19 at pci0 dev 25 function 5: vendor 1022 product 1465 (rev. 0x00)
pchb20 at pci0 dev 25 function 6: vendor 1022 product 1466 (rev. 0x00)
pchb21 at pci0 dev 25 function 7: vendor 1022 product 1467 (rev. 0x00)
isa0 at pcib0
pckbc0 at isa0 port 0x60-0x64
pci11 at mainbus0 bus 64
pci11: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
amdsmn1 at pci11 dev 0 function 0: AMD Family 17h System Management Network
amdzentemp1 at amdsmn1: AMD CPU Temperature Sensors (Family17h)
vendor 1022 product 1451 (IOMMU system) at pci11 dev 0 function 2 not configured
pchb22 at pci11 dev 1 function 0: vendor 1022 product 1452 (rev. 0x00)
ppb10 at pci11 dev 1 function 1: vendor 1022 product 1453 (rev. 0x00)
ppb10: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x16 @ 8.0GT/s
ppb10: link is x16 @ 2.5GT/s
pci12 at ppb10 bus 65
pci12: i/o space, memory space enabled, rd/line, wr/inv ok
nouveau0 at pci12 dev 0 function 0: vendor 10de product 1401 (rev. 0xa1)
nouveau0: info: NVIDIA GM206 (126010a1)
nouveau0: info: bios: version 84.06.14.00.ff
nouveau0: info: gr: using external firmware
firmware_open(nouveau/nvidia/gm206/fecs_inst.bin) called too early.
nouveau0: autoconfiguration error: error: gr: failed to load fecs_inst
nouveau0: notice: disp: dcb 15 type 8 unknown
nouveau0: info: fb: 4096 MiB GDDR5
Zone kernel: Available graphics memory: 17983376 kiB
Zone dma32: Available graphics memory: 2097152 kiB
nouveau0: info: DRM: VRAM: 4096 MiB
nouveau0: info: DRM: GART: 1048576 MiB
nouveau0: info: DRM: TMDS table version 2.0
nouveau0: info: DRM: DCB version 4.1
nouveau0: info: DRM: DCB outp 00: 01000f02 00020030
nouveau0: info: DRM: DCB outp 01: 02000f00 00000000
nouveau0: info: DRM: DCB outp 02: 02811f76 04400020
nouveau0: info: DRM: DCB outp 03: 02011f72 00020020
nouveau0: info: DRM: DCB outp 04: 04822f86 04400010
nouveau0: info: DRM: DCB outp 05: 04022f82 00020010
nouveau0: info: DRM: DCB outp 06: 04833f96 04400020
nouveau0: info: DRM: DCB outp 07: 04033f92 00020020
nouveau0: info: DRM: DCB outp 08: 02044f62 00020010
nouveau0: info: DRM: DCB outp 15: 01df5ff8 00000000
nouveau0: info: DRM: DCB conn 00: 00001030
nouveau0: info: DRM: DCB conn 01: 00020146
nouveau0: info: DRM: DCB conn 02: 01000246
nouveau0: info: DRM: DCB conn 03: 02000346
nouveau0: info: DRM: DCB conn 04: 00010461
nouveau0: info: DRM: DCB conn 05: 00000570
nouveau0: autoconfiguration error: error: DRM: Pointer to flat panel table invalid
nouveau0: autoconfiguration error: warn: DRM: unknown connector type 70
nouveau0: autoconfiguration error: warn: DRM: failed to create encoder 1/8/0: -19
nouveau0: autoconfiguration error: warn: DRM: Unknown-1 has no encoders, removing
kern info: [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
kern info: [drm] Driver supports precise vblank timestamp query.
nouveau0: info: DRM: MM: using COPY for buffer copies
nouveaufb0 at nouveau0
nouveaufb0: framebuffer at 0xffff95965b7ec000, size 1920x1080, depth 32, stride 7680
wsdisplay0 at nouveaufb0 kbdmux 1: console (default, vt100 emulation)
wsmux1: connecting to wsdisplay0
hdaudio1 at pci12 dev 0 function 1: HD Audio Controller
hdaudio1: interrupting at msi6 vec 0
hdafg1 at hdaudio1: vendor 10de product 0072
hdafg1: DP00 8ch: Digital Out [Jack]
hdafg1: DP01 8ch: Digital Out [Jack]
hdafg1: ELD version=0x2,len=32,edid=0x3,port=0x0,vendor=0xd109,product=0x8030
hdafg1: Monitor = 'BenQ PD2720U'
hdafg1: SAD id=0,format=1,channels=2,rate=0x07,precision=0x7
hdafg1: DP02 8ch: Digital Out [Jack]
hdafg1: DP03 8ch: Digital Out [Jack]
hdafg1: 8ch/0ch 48000Hz PCM16*
pchb23 at pci11 dev 2 function 0: vendor 1022 product 1452 (rev. 0x00)
pchb24 at pci11 dev 3 function 0: vendor 1022 product 1452 (rev. 0x00)
pchb25 at pci11 dev 4 function 0: vendor 1022 product 1452 (rev. 0x00)
pchb26 at pci11 dev 7 function 0: vendor 1022 product 1452 (rev. 0x00)
ppb11 at pci11 dev 7 function 1: vendor 1022 product 1454 (rev. 0x00)
ppb11: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x16 @ 8.0GT/s
pci13 at ppb11 bus 66
pci13: i/o space, memory space enabled, rd/line, wr/inv ok
vendor 1022 product 145a (non-essential instrumentation, subclass 0x00) at pci13 dev 0 function 0 not configured
vendor 1022 product 1456 (miscellaneous crypto) at pci13 dev 0 function 2 not configured
xhci2 at pci13 dev 0 function 3: vendor 1022 product 145f (rev. 0x00)
xhci2: interrupting at msix7 vec 0
xhci2: xHCI version 1.0
usb4 at xhci2: USB revision 3.0
usb5 at xhci2: USB revision 2.0
pchb27 at pci11 dev 8 function 0: vendor 1022 product 1452 (rev. 0x00)
ppb12 at pci11 dev 8 function 1: vendor 1022 product 1454 (rev. 0x00)
ppb12: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x16 @ 8.0GT/s
pci14 at ppb12 bus 67
pci14: i/o space, memory space enabled, rd/line, wr/inv ok
vendor 1022 product 1455 (non-essential instrumentation, subclass 0x00) at pci14 dev 0 function 0 not configured
ahcisata2 at pci14 dev 0 function 2: vendor 1022 product 7901 (rev. 0x51)
ahcisata2: 64-bit DMA
ahcisata2: AHCI revision 1.31, 1 port, 32 slots, CAP 0xf737ff00<PSC,SSC,PMD,FBSS,SPM,SAM,ISS=0x3=Gen3,SCLO,SAL,SALP,SMPS,SSNTF,SNCQ,S64A>
ahcisata2: interrupting at msi8 vec 0
atabus9 at ahcisata2 channel 0
acpicpu0 at cpu0: ACPI CPU
acpicpu0: C1: FFH, lat 1 us, pow 0 mW
acpicpu0: C2: I/O, lat 400 us, pow 0 mW
acpicpu0: P0: FFH, lat 1 us, pow 3762 mW, 3500 MHz
acpicpu0: P1: FFH, lat 1 us, pow 2415 mW, 2800 MHz
acpicpu0: P2: FFH, lat 1 us, pow 1897 mW, 2200 MHz
acpicpu1 at cpu1: ACPI CPU
acpicpu2 at cpu2: ACPI CPU
acpicpu3 at cpu3: ACPI CPU
acpicpu4 at cpu4: ACPI CPU
acpicpu5 at cpu5: ACPI CPU
acpicpu6 at cpu6: ACPI CPU
acpicpu7 at cpu7: ACPI CPU
acpicpu8 at cpu8: ACPI CPU
acpicpu9 at cpu9: ACPI CPU
acpicpu10 at cpu10: ACPI CPU
acpicpu11 at cpu11: ACPI CPU
acpicpu12 at cpu12: ACPI CPU
acpicpu13 at cpu13: ACPI CPU
acpicpu14 at cpu14: ACPI CPU
acpicpu15 at cpu15: ACPI CPU
acpicpu16 at cpu16: ACPI CPU
acpicpu17 at cpu17: ACPI CPU
acpicpu18 at cpu18: ACPI CPU
acpicpu19 at cpu19: ACPI CPU
acpicpu20 at cpu20: ACPI CPU
acpicpu21 at cpu21: ACPI CPU
acpicpu22 at cpu22: ACPI CPU
acpicpu23 at cpu23: ACPI CPU
acpicpu24 at cpu24: ACPI CPU
acpicpu25 at cpu25: ACPI CPU
acpicpu26 at cpu26: ACPI CPU
acpicpu27 at cpu27: ACPI CPU
acpicpu28 at cpu28: ACPI CPU
acpicpu29 at cpu29: ACPI CPU
acpicpu30 at cpu30: ACPI CPU
acpicpu31 at cpu31: ACPI CPU
nouveau0: autoconfiguration error: error: disp: chid 1 mthd 0080 data 00000000 00005080 0000000d
nouveau0: info: disp: Base 1:
nouveau0: info: disp: 0080: 00000000
nouveau0: info: disp: 0084: 00000000 -> 00000010
nouveau0: info: disp: 0088: 00000000 -> 00000100
nouveau0: info: disp: 008c: 00000000
nouveau0: info: disp: 0090: 00000000 -> 00000001
nouveau0: info: disp: 0094: 00000000 -> f0000000
nouveau0: info: disp: 00a0: 00000000
nouveau0: info: disp: 00a4: 00000000
nouveau0: info: disp: 00c0: 00000000 -> ffff0000
nouveau0: info: disp: 00c4: 00000000
nouveau0: info: disp: 00c8: 00000000
nouveau0: info: disp: 00cc: 00000000
nouveau0: info: disp: 00e0: 00000000 -> 40000000
nouveau0: info: disp: 00e4: 00000000
nouveau0: info: disp: 00e8: 00000000
nouveau0: info: disp: 00ec: 00000000
nouveau0: info: disp: 00fc: 00000000
nouveau0: info: disp: 0100: fffe0000
nouveau0: info: disp: 0104: 00000000
nouveau0: info: disp: 0108: 18131813
nouveau0: info: disp: 010c: f0000000
nouveau0: info: disp: 0110: 00000000
nouveau0: info: disp: 0114: 00000000
nouveau0: info: disp: 0118: 00000000
nouveau0: info: disp: 011c: 00000000
nouveau0: info: disp: 0130: 00000000
nouveau0: info: disp: 0134: 00000000
nouveau0: info: disp: 0138: 00000000
nouveau0: info: disp: 013c: 00000000
nouveau0: info: disp: 0140: 00010000
nouveau0: info: disp: 0144: 00000000
nouveau0: info: disp: 0148: 00000000
nouveau0: info: disp: 014c: 00000000
nouveau0: info: disp: 0150: 00000000
nouveau0: info: disp: 0154: 00010000
nouveau0: info: disp: 0158: 00000000
nouveau0: info: disp: 015c: 00000000
nouveau0: info: disp: 0160: 00000000
nouveau0: info: disp: 0164: 00000000
nouveau0: info: disp: 0168: 00010000
nouveau0: info: disp: 016c: 00000000
nouveau0: info: disp: Base 1 - Image 0:
nouveau0: info: disp: 0400: 00000000 -> 00000600
nouveau0: info: disp: 0404: 00000000
nouveau0: info: disp: 0408: 00000000 -> 04380780
nouveau0: info: disp: 040c: 00000000 -> 01001e00
nouveau0: info: disp: 0410: 0000e900 -> 0000cf00
nouveau0: info: disp: Base 1 - Image 1:
nouveau0: info: disp: 0420: 00000000
nouveau0: info: disp: 0424: 00000000
nouveau0: info: disp: 0428: 00000000
nouveau0: info: disp: 042c: 00000000
nouveau0: info: disp: 0430: 0000e900
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
autoconfiguration error: ERROR: 491 cycle TSC drift observed
uhub0 at usb0: NetBSD (0000) xHCI root hub (0000), class 9/0, rev 3.00/1.00, addr 0
uhub0: 6 ports with 6 removable, self powered
uhub1 at usb1: NetBSD (0000) xHCI root hub (0000), class 9/0, rev 2.00/1.00, addr 0
uhub1: 14 ports with 14 removable, self powered
uhub2 at usb2: NetBSD (0000) xHCI root hub (0000), class 9/0, rev 3.00/1.00, addr 0
uhub2: 4 ports with 4 removable, self powered
uhub3 at usb3: NetBSD (0000) xHCI root hub (0000), class 9/0, rev 2.00/1.00, addr 0
uhub3: 4 ports with 4 removable, self powered
uhub4 at usb4: NetBSD (0000) xHCI root hub (0000), class 9/0, rev 3.00/1.00, addr 0
uhub4: 4 ports with 4 removable, self powered
uhub5 at usb5: NetBSD (0000) xHCI root hub (0000), class 9/0, rev 2.00/1.00, addr 0
uhub5: 4 ports with 4 removable, self powered
ahcisata0 port 5: device present, speed: 6.0Gb/s
autoconfiguration error: ahcisata0 port 5: clearing WDCTL_RST failed for drive 15
autoconfiguration error: ahcisata0 port 5: drive 15 reset failed, disabling PMP
ahcisata0 port 5: device present, speed: 6.0Gb/s
uhidev0 at uhub5 port 1 configuration 1 interface 0
uhidev0: vendor 046a (0x46a) product 0023 (0x23), rev 2.00/2.20, addr 1, iclass 3/1
ukbd0 at uhidev0: 8 Variable keys, 6 Array codes
wskbd0 at ukbd0: console keyboard, using wsdisplay0
uhidev1 at uhub5 port 1 configuration 1 interface 1
uhidev1: vendor 046a (0x46a) product 0023 (0x23), rev 2.00/2.20, addr 1, iclass 3/0
uhidev1: 2 report ids
uhid0 at uhidev1 reportid 1: input=2, output=0, feature=0
uhid1 at uhidev1 reportid 2: input=1, output=0, feature=0
wd0 at atabus5 drive 0
wd0: <Samsung SSD 860 EVO 250GB>
wd0: drive supports 1-sector PIO transfers, LBA48 addressing
wd0: 232 GB, 484521 cyl, 16 head, 63 sec, 512 bytes/sect x 488397168 sectors
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133), WRITE DMA FUA, NCQ (32 tags)
wd0(ahcisata0:5:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) (using DMA), NCQ (31 tags)
IPsec: Initialized Security Association Processing.
WARNING: 12 errors while detecting hardware; check system log.
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
kern.module.path=/stand/amd64/8.99.42/modules
wsdisplay0: screen 1 added (default, vt100 emulation)
wsdisplay0: screen 2 added (default, vt100 emulation)
wsdisplay0: screen 3 added (default, vt100 emulation)
wsdisplay0: screen 4 added (default, vt100 emulation)
# X -configure
X.Org X Server 1.20.4
X Protocol Version 11, Revision 0
Build Operating System: NetBSD/amd64 8.99.42 - The NetBSD Foundation, Inc.
Current Operating System: NetBSD hostname 8.99.42 NetBSD 8.99.42 (HOSTNAME) #0: Fri May 31 17:53:20 CEST 2019 hostname:/usr/obj/sys/arch/amd64/compile/HOSTNAME amd64
Build Date: 03 March 2019 07:11:23AM
Current version of pixman: 0.38.0
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Fri May 31 19:09:19 2019
List of video drivers:
amdgpu
amdgpu
ast
ast
ati
ati
chips
chips
cirrus
cirrus
i128
i128
i740
i740
intel
intel
kbd
kbd
mach64
mach64
mga
mga
mouse
mouse
neomagic
neomagic
nouveau
nouveau
nv
nv
openchrome
openchrome
r128
r128
radeon
radeon
s3
s3
s3virge
s3virge
savage
savage
siliconmotion
siliconmotion
sis
sis
tdfx
tdfx
tga
tga
trident
trident
tseng
tseng
vboxvideo
vboxvideo
vmmouse
vmmouse
vmware
vmware
ws
ws
modesetting
modesetting
vesa
vesa
wsfb
wsfb
No devices to configure. Configuration failed.
(EE) Server terminated with error (2). Closing log file.
#
[ 1157.769]
X.Org X Server 1.20.4
X Protocol Version 11, Revision 0
[ 1157.769] Build Operating System: NetBSD/amd64 8.99.42 - The NetBSD Foundation, Inc.
[ 1157.770] Current Operating System: NetBSD hostname 8.99.42 NetBSD 8.99.42 (HOSTNAME) #0: Fri May 31 17:53:20 CEST 2019 wiz@hostname:/usr/obj/sys/arch/amd64/compile/HOSTNAME amd64
[ 1157.770] Build Date: 03 March 2019 07:11:23AM
[ 1157.770]
[ 1157.770] Current version of pixman: 0.38.0
[ 1157.771] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 1157.771] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 1157.771] (==) Log file: "/var/log/Xorg.0.log", Time: Fri May 31 19:08:43 2019
[ 1157.773] (II) Loader magic: 0x508ea20
[ 1157.773] (II) Module ABI versions:
[ 1157.773] X.Org ANSI C Emulation: 0.4
[ 1157.773] X.Org Video Driver: 24.0
[ 1157.773] X.Org XInput driver : 24.1
[ 1157.773] X.Org Server Extension : 10.0
[ 1157.789] (==) Using default built-in configuration (21 lines)
[ 1157.789] (==) --- Start of built-in configuration ---
[ 1157.789] Section "Device"
[ 1157.789] Identifier "Builtin Default fbdev Device 0"
[ 1157.789] Driver "fbdev"
[ 1157.789] EndSection
[ 1157.789] Section "Screen"
[ 1157.789] Identifier "Builtin Default fbdev Screen 0"
[ 1157.789] Device "Builtin Default fbdev Device 0"
[ 1157.789] EndSection
[ 1157.789] Section "Device"
[ 1157.789] Identifier "Builtin Default vesa Device 0"
[ 1157.789] Driver "vesa"
[ 1157.789] EndSection
[ 1157.789] Section "Screen"
[ 1157.789] Identifier "Builtin Default vesa Screen 0"
[ 1157.789] Device "Builtin Default vesa Device 0"
[ 1157.789] EndSection
[ 1157.789] Section "ServerLayout"
[ 1157.789] Identifier "Builtin Default Layout"
[ 1157.789] Screen "Builtin Default fbdev Screen 0"
[ 1157.789] Screen "Builtin Default vesa Screen 0"
[ 1157.789] EndSection
[ 1157.789] (==) --- End of built-in configuration ---
[ 1157.789] (==) ServerLayout "Builtin Default Layout"
[ 1157.789] (**) |-->Screen "Builtin Default fbdev Screen 0" (0)
[ 1157.789] (**) | |-->Monitor "<default monitor>"
[ 1157.790] (**) | |-->Device "Builtin Default fbdev Device 0"
[ 1157.790] (==) No monitor specified for screen "Builtin Default fbdev Screen 0".
Using a default monitor configuration.
[ 1157.790] (**) |-->Screen "Builtin Default vesa Screen 0" (1)
[ 1157.790] (**) | |-->Monitor "<default monitor>"
[ 1157.790] (**) | |-->Device "Builtin Default vesa Device 0"
[ 1157.790] (==) No monitor specified for screen "Builtin Default vesa Screen 0".
Using a default monitor configuration.
[ 1157.790] (==) Not automatically adding devices
[ 1157.790] (==) Not automatically enabling devices
[ 1157.790] (==) Not automatically adding GPU devices
[ 1157.790] (==) Max clients allowed: 256, resource mask: 0x1fffff
[ 1157.791] (==) FontPath set to:
/usr/X11R7/lib/X11/fonts/misc/,
/usr/X11R7/lib/X11/fonts/TTF/,
/usr/X11R7/lib/X11/fonts/Type1/,
/usr/X11R7/lib/X11/fonts/75dpi/,
/usr/X11R7/lib/X11/fonts/100dpi/
[ 1157.791] (==) ModulePath set to "/usr/X11R7/lib/modules"
[ 1157.791] (==) |-->Input Device "<default pointer>"
[ 1157.791] (==) |-->Input Device "<default keyboard>"
[ 1157.791] (==) The core pointer device wasn't specified explicitly in the layout.
Using the default mouse configuration.
[ 1157.791] (==) The core keyboard device wasn't specified explicitly in the layout.
Using the default keyboard configuration.
[ 1157.792] (II) LoadModule: "glx"
[ 1157.796] (II) Loading /usr/X11R7/lib/modules/extensions/libglx.so
[ 1157.798] (II) Module glx: vendor="X.Org Foundation"
[ 1157.798] compiled for 1.20.4, module version = 1.0.0
[ 1157.798] ABI class: X.Org Server Extension, version 10.0
[ 1157.799] (II) LoadModule: "fbdev"
[ 1157.804] (WW) Warning, couldn't open module fbdev
[ 1157.804] (EE) Failed to load module "fbdev" (module does not exist, 0)
[ 1157.804] (II) LoadModule: "vesa"
[ 1157.806] (II) Loading /usr/X11R7/lib/modules/drivers/vesa_drv.so
[ 1157.806] (II) Module vesa: vendor="X.Org Foundation"
[ 1157.806] compiled for 1.20.4, module version = 2.4.0
[ 1157.807] Module class: X.Org Video Driver
[ 1157.807] ABI class: X.Org Video Driver, version 24.0
[ 1157.807] (II) LoadModule: "mouse"
[ 1157.808] (II) Loading /usr/X11R7/lib/modules/drivers/mouse_drv.so
[ 1157.808] (II) Module mouse: vendor="X.Org Foundation"
[ 1157.808] compiled for 1.20.4, module version = 1.9.2
[ 1157.809] Module class: X.Org XInput Driver
[ 1157.809] ABI class: X.Org XInput driver, version 24.1
[ 1157.809] (II) LoadModule: "kbd"
[ 1157.810] (II) Loading /usr/X11R7/lib/modules/drivers/kbd_drv.so
[ 1157.810] (II) Module kbd: vendor="X.Org Foundation"
[ 1157.810] compiled for 1.20.4, module version = 1.9.0
[ 1157.810] Module class: X.Org XInput Driver
[ 1157.810] ABI class: X.Org XInput driver, version 24.1
[ 1157.810] (II) VESA: driver for VESA chipsets: vesa
[ 1157.811] (--) Using wscons driver on /dev/ttyE4 in pcvt compatibility mode (version 3.32)
[ 1157.811] (--) using VT number 5
[ 1157.824] (EE) No devices detected.
[ 1157.824] (EE)
Fatal server error:
[ 1157.824] (EE) no screens found(EE)
[ 1157.824] (EE)
Please consult the The X.Org Foundation support
at http://wiki.x.org
for help.
[ 1157.824] (EE) Please also check the log file at "/var/log/Xorg.0.log" for additional information.
[ 1157.825] (EE)
[ 1157.983] (EE) Server terminated with error (1). Closing log file.
Home |
Main Index |
Thread Index |
Old Index