tech-x11 archive

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index][Old Index]

re: i386 radeondrmkms results



On Mon, 12 Jan 2015, matthew green wrote:

> can you post the boot messages for drmkms?  it's really important
> for wsdisplay0 to attach at drmkms.

My attempt to boot -current GENERIC and disable pcdisplay0/vga0 via
userconf were ultimately unsuccesful.  The first attempt booting that
kernel after power-up always panicked with "cnopen: no console device".

Following reboot and disabling pcdisplay0/vga0 in userconf again, the
kernel didn't panic and the display wasn't black.  Instead it was filled
with garbage and the machine seemed to be hung.  Perhaps I didn't wait
long enough (see below).

I boot/run -current on the target machine via NFS, but the machine has
netbsd-7 installed on local disk.

For comparison, I tried the same procedure with a DRMKMS kernel from a
netbsd-7 build from sources dated about 201501111630Z.

The screen went black, but the disk activity light indicated that things
were continuing to happen (fontconfig cache update, etc.).  There was
a brief flicker that probably coincided with the X server starting, then
the machine rebooted (no crash dump).  Below is what I recovered of
"dmesg.boot" before returning to my usual UMS kernel:

[...]
PI: Found matching pin for 2.0.INTC at func 2: 9
LNKC: ACPI: Found matching pin for 2.2.INTA at func 0: 9
LNKE: Links after initial probe:
Link Device LNKE:
Index  IRQ  Rtd  Ref  IRQs
    0   10   N     0  3 4 5 6 7 9 10 11 polarity 1 trigger 0

LNKE: Links after initial validation:
Link Device LNKE:
Index  IRQ  Rtd  Ref  IRQs
    0   10   N     0  3 4 5 6 7 9 10 11 polarity 1 trigger 0

LNKE: Links after disable:
Link Device LNKE:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11 polarity 1 trigger 0

LNKE: ACPI: Found matching pin for 2.8.INTA at func 0: 10
acpi0: SCI interrupting at int 9
acpi0: fixed power button present
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
acpi0: ACPI-Fast 24-bit timer
acpiec0 at acpi0 (EC, PNP0C09-0): using acpiecdt0
MEM (PNP0C01) [System Board] at acpi0 not configured
acpilid0 at acpi0 (LID, PNP0C0D): ACPI Lid Switch
acpibut0 at acpi0 (SLPB, PNP0C0E): ACPI Sleep Button
SIO (PNP0C02) [Motherboard Register Resources] at acpi0 not configured
attimer1 at acpi0 (TIMR, PNP0100): io 0x40-0x43 irq 0
pcppi1 at acpi0 (SPKR, PNP0800): io 0x61
midi0 at pcppi1: PC speaker
sysbeep0 at pcppi1
FPU (PNP0C04) [Math Coprocessor] at acpi0 not configured
pckbc1 at acpi0 (KBD, PNP0303) (kbd port): io 0x60,0x64 irq 1
pckbc2 at acpi0 (MOU, IBM3780) (aux port): irq 12
FDC (PNP0700) [PC standard floppy disk controller] at acpi0 not configured
UART (PNP0501) [16550A-compatible COM port] at acpi0 not configured
ECP (PNP0401) [ECP printer port] at acpi0 not configured
acpibat0 at acpi0 (BAT0, PNP0C0A-0): ACPI Battery
acpibat0: SANYO LION rechargeable battery
acpibat0: model number y{}-02K6, serial number   417
acpibat0: granularity: low->warn 0.001 Wh, warn->full 0.001 Wh
acpibat1 at acpi0 (BAT1, PNP0C0A-1): ACPI Battery
acpiacad0 at acpi0 (AC, ACPI0003-0): ACPI AC Adapter
thinkpad0 at acpi0 (HKEY, IBM0068)
thinkpad0: using EC at acpiecdt0
acpivga0 at acpi0 (VID): ACPI Display Adapter
acpivga0: capabilities: _DOS _DOD
acpiout0 at acpivga0 (LCD0, 0x0110): ACPI Display Output Device
acpiout0: capabilities: _DDC _DCS _DGS _DSS
acpiout1 at acpivga0 (CRT0, 0x0100): ACPI Display Output Device
acpiout1: capabilities: _DDC _DCS _DGS _DSS
acpiout2 at acpivga0 (TV0, 0x0200): ACPI Display Output Device
acpiout2: capabilities: _DDC _DCS _DGS _DSS
acpiout3 at acpivga0 (DVI0, 0x0210): ACPI Display Output Device
acpiout3: capabilities: _DCS _DGS _DSS
acpivga0: connected output devices:
acpivga0:   0x0110 (acpiout0): LCD Panel, head 0
acpivga0:   0x0100 (acpiout1): Ext. Monitor, head 0
acpivga0:   0x0200 (acpiout2): TV, head 0
acpivga0:   0x0210 (acpiout3): Unknown Output Device, head 0
acpitz0 at acpi0 (THM0)
acpitz0: polling interval 30.0 seconds
acpitz0: levels: critical 94.0 C, passive 88.5 C, passive cooling
apm0 at acpi0: Power Management spec V1.2
ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20131218/hwxface-646)
ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20131218/hwxface-646)
acpi0: [FADT] FACS           : 0x000000007FF7F000
acpi0: [FADT] DSDT           : 0x000000007FF72F62
acpi0: [FADT] INT_MODEL      : 0x0000000000000000
acpi0: [FADT] PM_PROFILE     : 0x0000000000000000
acpi0: [FADT] SCI_INT        : 0x0000000000000009
acpi0: [FADT] SMI_CMD        : 0x00000000000000B2
acpi0: [FADT] ACPI_ENABLE    : 0x00000000000000F0
acpi0: [FADT] ACPI_DISABLE   : 0x00000000000000F1
acpi0: [FADT] S4BIOS_REQ     : 0x0000000000000000
acpi0: [FADT] PSTATE_CNT     : 0x0000000000000000
acpi0: [FADT] PM1a_EVT_BLK   : 0x0000000000001000
acpi0: [FADT] PM1b_EVT_BLK   : 0x0000000000000000
acpi0: [FADT] PM1a_CNT_BLK   : 0x0000000000001004
acpi0: [FADT] PM1b_CNT_BLK   : 0x0000000000000000
acpi0: [FADT] PM2_CNT_BLK    : 0x0000000000001020
acpi0: [FADT] PM_TMR_BLK     : 0x0000000000001008
acpi0: [FADT] GPE0_BLK       : 0x0000000000001028
acpi0: [FADT] GPE1_BLK       : 0x000000000000102C
acpi0: [FADT] PM1_EVT_LEN    : 0x0000000000000004
acpi0: [FADT] PM1_CNT_LEN    : 0x0000000000000002
acpi0: [FADT] PM2_CNT_LEN    : 0x0000000000000001
acpi0: [FADT] PM_TMR_LEN     : 0x0000000000000004
acpi0: [FADT] GPE0_BLK_LEN   : 0x0000000000000004
acpi0: [FADT] GPE1_BLK_LEN   : 0x0000000000000004
acpi0: [FADT] GPE1_BASE      : 0x0000000000000010
acpi0: [FADT] CST_CNT        : 0x0000000000000000
acpi0: [FADT] P_LVL2_LAT     : 0x0000000000000001
acpi0: [FADT] P_LVL3_LAT     : 0x0000000000000055
acpi0: [FADT] FLUSH_SIZE     : 0x0000000000000000
acpi0: [FADT] FLUSH_STRIDE   : 0x0000000000000000
acpi0: [FADT] DUTY_OFFSET    : 0x0000000000000001
acpi0: [FADT] DUTY_WIDTH     : 0x0000000000000003
acpi0: [FADT] DAY_ALRM       : 0x000000000000000D
acpi0: [FADT] MON_ALRM       : 0x0000000000000000
acpi0: [FADT] CENTURY        : 0x0000000000000032
acpi0: [FADT] IAPC_BOOT_ARCH : 0x0000000000000000
acpi0: [FADT] RESET_VALUE    : 0x0000000000000006
acpi0: [FADT] WBINVD         : 0x0000000000000001
acpi0: [FADT] WBINVD_FLUSH   : 0x0000000000000000
acpi0: [FADT] PROC_C1        : 0x0000000000000004
acpi0: [FADT] P_LVL2_UP      : 0x0000000000000008
acpi0: [FADT] PWR_BUTTON     : 0x0000000000000000
acpi0: [FADT] SLP_BUTTON     : 0x0000000000000020
acpi0: [FADT] FIX_RTC        : 0x0000000000000000
acpi0: [FADT] RTC_S4         : 0x0000000000000080
acpi0: [FADT] TMR_VAL_EXT    : 0x0000000000000000
acpi0: [FADT] DCK_CAP        : 0x0000000000000200
acpi0: [FADT] RESET_REG_SUP  : 0x0000000000000000
acpi0: [FADT] SEALED_CASE    : 0x0000000000000000
acpi0: [FADT] HEADLESS       : 0x0000000000000000
acpi0: [FADT] CPU_SW_SLP     : 0x0000000000000000
acpi0: [FADT] PCI_EXP_WAK    : 0x0000000000000000
acpi0: [FADT] PLATFORM_CLK   : 0x0000000000000000
acpi0: [FADT] S4_RTC_STS     : 0x0000000000000000
acpi0: [FADT] REMOTE_POWER   : 0x0000000000000000
acpi0: [FADT] APIC_CLUSTER   : 0x0000000000000000
acpi0: [FADT] APIC_PHYSICAL  : 0x0000000000000000
acpi0: [\   ] HID -          UID -    STA 0xFFFFFFFF ADR -
acpi0: [CPU ] HID -          UID -    STA 0xFFFFFFFF ADR -
acpi0: [_SB ] HID -          UID -    STA 0xFFFFFFFF ADR -
acpi0: [LNKA] HID PNP0C0F    UID 1    STA 0x0000000B ADR -
acpi0: [LNKB] HID PNP0C0F    UID 2    STA 0x0000000B ADR -
acpi0: [LNKC] HID PNP0C0F    UID 3    STA 0x0000000B ADR -
acpi0: [LNKD] HID PNP0C0F    UID 4    STA 0x0000000B ADR -
acpi0: [LNKE] HID PNP0C0F    UID 5    STA 0x0000000B ADR -
acpi0: [LNKF] HID PNP0C0F    UID 6    STA 0x00000009 ADR -
acpi0: [LNKG] HID PNP0C0F    UID 7    STA 0x00000009 ADR -
acpi0: [LNKH] HID PNP0C0F    UID 8    STA 0x00000009 ADR -
acpi0: [MEM ] HID PNP0C01    UID -    STA 0xFFFFFFFF ADR -
acpi0: [LID ] HID PNP0C0D    UID -    STA 0xFFFFFFFF ADR -
acpi0: [SLPB] HID PNP0C0E    UID -    STA 0xFFFFFFFF ADR -
acpi0: [PCI0] HID PNP0A03    UID -    STA 0xFFFFFFFF ADR 0x0000000000000000
acpi0: [LPC ] HID -          UID -    STA 0xFFFFFFFF ADR 0x00000000001F0000
acpi0: [SIO ] HID PNP0C02    UID 0    STA 0xFFFFFFFF ADR -
acpi0: [PIC ] HID PNP0000    UID -    STA 0xFFFFFFFF ADR -
acpi0: [TIMR] HID PNP0100    UID -    STA 0xFFFFFFFF ADR -
acpi0: [DMAC] HID PNP0200    UID -    STA 0xFFFFFFFF ADR -
acpi0: [SPKR] HID PNP0800    UID -    STA 0xFFFFFFFF ADR -
acpi0: [FPU ] HID PNP0C04    UID -    STA 0xFFFFFFFF ADR -
acpi0: [RTC ] HID PNP0B00    UID -    STA 0xFFFFFFFF ADR -
acpi0: [KBD ] HID PNP0303    UID -    STA 0xFFFFFFFF ADR -
acpi0: [MOU ] HID IBM3780    UID -    STA 0xFFFFFFFF ADR -
acpi0: [FDC ] HID PNP0700    UID -    STA 0x0000000F ADR -
acpi0: [FDD0] HID -          UID -    STA 0xFFFFFFFF ADR 0x0000000000000000
acpi0: [UART] HID PNP0501    UID -    STA 0x0000000F ADR -
acpi0: [LPT ] HID PNP0400    UID -    STA 0x00000000 ADR -
acpi0: [ECP ] HID PNP0401    UID -    STA 0x0000000F ADR -
acpi0: [FIR ] HID IBM0071    UID -    STA 0x0000000D ADR -
acpi0: [EC  ] HID PNP0C09    UID 0    STA 0xFFFFFFFF ADR -
acpi0: [PUBS] HID -          UID -    STA          - ADR -
acpi0: [BAT0] HID PNP0C0A    UID 0    STA 0x0000001F ADR -
acpi0: [BAT1] HID PNP0C0A    UID 1    STA 0x0000000F ADR -
acpi0: [AC  ] HID ACPI0003   UID 0    STA 0x0000000F ADR -
acpi0: [HKEY] HID IBM0068    UID -    STA 0x0000000F ADR -
acpi0: [AGP ] HID -          UID -    STA 0xFFFFFFFF ADR 0x0000000000010000
acpi0: [VID ] HID -          UID -    STA 0xFFFFFFFF ADR 0x0000000000000000
acpi0: [LCD0] HID -          UID -    STA 0xFFFFFFFF ADR 0x0000000000000110
acpi0: [CRT0] HID -          UID -    STA 0xFFFFFFFF ADR 0x0000000000000100
acpi0: [TV0 ] HID -          UID -    STA 0xFFFFFFFF ADR 0x0000000000000200
acpi0: [DVI0] HID -          UID -    STA 0xFFFFFFFF ADR 0x0000000000000210
acpi0: [PCI1] HID -          UID -    STA 0xFFFFFFFF ADR 0x00000000001E0000
acpi0: [CBS0] HID -          UID -    STA 0xFFFFFFFF ADR 0x0000000000000000
acpi0: [CBS1] HID -          UID -    STA 0xFFFFFFFF ADR 0x0000000000000001
acpi0: [DOCK] HID -          UID 0    STA 0x00000000 ADR 0x0000000000030000
acpi0: [IDE1] HID -          UID -    STA 0x00000000 ADR 0x0000000000010000
acpi0: [PRIM] HID -          UID -    STA 0xFFFFFFFF ADR 0x0000000000000000
acpi0: [MSTR] HID -          UID -    STA 0xFFFFFFFF ADR 0x0000000000000000
acpi0: [CBS2] HID -          UID -    STA 0x00000000 ADR 0x0000000000020000
acpi0: [CBS3] HID -          UID -    STA 0x00000000 ADR 0x0000000000020001
acpi0: [IDE0] HID -          UID -    STA 0xFFFFFFFF ADR 0x00000000001F0001
acpi0: [PRIM] HID -          UID -    STA 0xFFFFFFFF ADR 0x0000000000000000
acpi0: [MSTR] HID -          UID -    STA 0xFFFFFFFF ADR 0x0000000000000000
acpi0: [SLAV] HID -          UID -    STA 0x00000000 ADR 0x0000000000000001
acpi0: [SCND] HID -          UID -    STA 0xFFFFFFFF ADR 0x0000000000000001
acpi0: [MSTR] HID -          UID -    STA 0x0000000F ADR 0x0000000000000000
acpi0: [USB0] HID -          UID -    STA 0xFFFFFFFF ADR 0x00000000001D0000
acpi0: [URTH] HID -          UID -    STA 0xFFFFFFFF ADR 0x0000000000000000
acpi0: [UPDK] HID -          UID -    STA 0x0000000F ADR 0x0000000000000001
acpi0: [UNST] HID -          UID -    STA 0x00000000 ADR 0x0000000000000002
acpi0: [USB1] HID -          UID -    STA 0xFFFFFFFF ADR 0x00000000001D0001
acpi0: [USB2] HID -          UID -    STA 0xFFFFFFFF ADR 0x00000000001D0002
acpi0: [AC97] HID -          UID -    STA 0xFFFFFFFF ADR 0x00000000001F0006
acpi0: [SWAP] HID IBM0069    UID -    STA 0x00000000 ADR -
acpi0: [NEST] HID IBM006A    UID -    STA 0x00000000 ADR -
acpi0: [_TZ ] HID -          UID -    STA 0xFFFFFFFF ADR -
acpi0: [THM0] HID -          UID -    STA          - ADR -

\     [06] []
    CPU   [12] []
    _SB   [06] []
        LNKA  [06] []
        LNKB  [06] []
        LNKC  [06] []
        LNKD  [06] []
        LNKE  [06] []
        LNKF  [06] []
        LNKG  [06] []
        LNKH  [06] []
        MEM   [06] []
        LID   [06] [] <acpilid0>
        SLPB  [06] [] <acpibut0>
        PCI0  [06] [] (PCI) @ 0x00:0x00:0x00:0x00 [R] [B] -> 0x00:0x00
            LPC   [06] [] (PCI) @ 0x00:0x00:0x1F:0x00
                SIO   [06] []
                PIC   [06] []
                TIMR  [06] [] <attimer1>
                DMAC  [06] []
                SPKR  [06] [] <pcppi1>
                FPU   [06] []
                RTC   [06] []
                KBD   [06] [] <pckbc1>
                MOU   [06] [] <pckbc2>
                FDC   [06] []
                    FDD0  [06] []
                UART  [06] []
                LPT   [06] []
                ECP   [06] []
                FIR   [06] []
                EC    [06] [] <acpiec0>
                    PUBS  [11] []
                    BAT0  [06] [] <acpibat0>
                    BAT1  [06] [] <acpibat1>
                    AC    [06] [] <acpiacad0>
                    HKEY  [06] [] <thinkpad0>
            AGP   [06] [] (PCI) @ 0x00:0x00:0x01:0x00 [B] -> 0x00:0x01
                VID   [06] [] <acpivga0> (PCI) @ 0x00:0x01:0x00:0x00
                    LCD0  [06] [] <acpiout0>
                    CRT0  [06] [] <acpiout1>
                    TV0   [06] [] <acpiout2>
                    DVI0  [06] [] <acpiout3>
            PCI1  [06] [] (PCI) @ 0x00:0x00:0x1E:0x00 [B] -> 0x00:0x02
                CBS0  [06] [] (PCI) @ 0x00:0x02:0x00:0x00
                CBS1  [06] [] (PCI) @ 0x00:0x02:0x00:0x01
                DOCK  [06] []
                    IDE1  [06] []
                        PRIM  [06] []
                            MSTR  [06] []
                    CBS2  [06] []
                    CBS3  [06] []
            IDE0  [06] [] (PCI) @ 0x00:0x00:0x1F:0x01
                PRIM  [06] []
                    MSTR  [06] []
                    SLAV  [06] []
                SCND  [06] []
                    MSTR  [06] []
            USB0  [06] [] (PCI) @ 0x00:0x00:0x1D:0x00
                URTH  [06] []
                    UPDK  [06] []
                    UNST  [06] []
            USB1  [06] [] (PCI) @ 0x00:0x00:0x1D:0x01
            USB2  [06] [] (PCI) @ 0x00:0x00:0x1D:0x02
            AC97  [06] [] (PCI) @ 0x00:0x00:0x1F:0x06
        SWAP  [06] []
        NEST  [06] []
    _TZ   [06] []
        THM0  [13] [] <acpitz0>
attimer1: attached to pcppi1
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc1 (aux slot)
pms0: synaptics_probe: Not synaptics.
pckbc1: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0: Intel 82845 Host (rev. 0x04)
agp0 at pchb0: aperture at 0xe0000000, size 0x4000000
ppb0 at pci0 dev 1 function 0: Intel 82845 AGP (rev. 0x04)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
radeon0 at pci1 dev 0 function 0: ATI Technologies FireGL Mobility 7800 M7 LX (rev. 0x00)
radeon0: WARNING: power management not supported
uhci0 at pci0 dev 29 function 0: Intel 82801CA USB Controller (rev. 0x02)
uhci0: interrupting at irq 9
usb0 at uhci0: USB revision 1.0
usb0: WARNING: power management not supported
uhci1 at pci0 dev 29 function 1: Intel 82801CA USB Controller (rev. 0x02)
uhci1: interrupting at irq 11
usb1 at uhci1: USB revision 1.0
usb1: WARNING: power management not supported
uhci2 at pci0 dev 29 function 2: Intel 82801CA USB Controller (rev. 0x02)
uhci2: interrupting at irq 9
usb2 at uhci2: USB revision 1.0
usb2: WARNING: power management not supported
ppb1 at pci0 dev 30 function 0: Intel 82801BAM Hub-PCI Bridge (rev. 0x42)
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled
cbb0 at pci2 dev 0 function 0: Ricoh 5C476 PCI-CardBus Bridge (rev. 0xa8)
cbb0: can't map socket base address 0x50000000
pci_io_find: expected type i/o, found mem
cbb0: can't map socket base address 0xc0ea216a: io mode
cbb1 at pci2 dev 0 function 1: Ricoh 5C476 PCI-CardBus Bridge (rev. 0xa8)
cbb1: can't map socket base address 0x50100000
pci_io_find: expected type i/o, found mem
cbb1: can't map socket base address 0xc0ea216a: io mode
fwohci0 at pci2 dev 0 function 2: Ricoh 5C552 PCI-CardBus Bridge/Firewire (rev. 0x00)
fwohci0: interrupting at irq 9
fwohci0: OHCI version 1.0 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:06:1b:00:10:00:72:5f
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwohci0: Initiate bus reset
iwi0 at pci2 dev 2 function 0: Intel PRO/Wireless LAN 2915ABG Mini-PCI Adapter (rev. 0x05)
iwi0: interrupting at irq 9
iwi0: 802.11 address 00:16:6f:6f:63:f4
iwi0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
iwi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
iwi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
fxp0 at pci2 dev 8 function 0: Intel PRO/100 VE Network Controller (rev. 0x42)
fxp0: interrupting at irq 10
fxp0: detected 64 word EEPROM
fxp0: Ethernet address xx:xx:xx:xx:xx:xx
inphy0 at fxp0 phy 1: i82562ET 10/100 media interface, rev. 0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
cbb0: osock_ctrl 0x400 sock_ctrl 0x400
cbb0: wait took 0.040012s
cbb0: cacheline 0x0 lattimer 0x40
cbb0: bhlc 0x824000
cbb0: interrupting at irq 9
cardslot0 at cbb0
cardbus0 at cardslot0: bus 3 cacheline 0x0, lattimer 0x40
pcmcia0 at cardslot0
cbb1: osock_ctrl 0x400 sock_ctrl 0x400
cbb1: wait took 0.040010s
cbb1: cacheline 0x0 lattimer 0x40
cbb1: bhlc 0x824000
cbb1: interrupting at irq 5
cardslot1 at cbb1
cardbus1 at cardslot1: bus 6 cacheline 0x0, lattimer 0x40
pcmcia1 at cardslot1
ichlpcib0 at pci0 dev 31 function 0: Intel 82801CAM LPC Interface Bridge (rev. 0x02)
timecounter: Timecounter "ichlpcib0" frequency 3579545 Hz quality 1000
ichlpcib0: 24-bit timer
ichlpcib0: TCO (watchdog) timer configured.
ichlpcib0: SpeedStep enabled
ichlpcib0: can't map general purpose i/o space(rv = 1)
ichlpcib0: fwh: data 46,20, id 20,2d
piixide0 at pci0 dev 31 function 1: Intel 82801CA IDE Controller (ICH3) (rev. 0x02)
piixide0: bus-master DMA support present
piixide0: primary channel configured to compatibility mode
piixide0: primary channel interrupting at irq 14
atabus0 at piixide0 channel 0
piixide0: secondary channel configured to compatibility mode
piixide0: secondary channel interrupting at irq 15
atabus1 at piixide0 channel 1
ichsmb0 at pci0 dev 31 function 3: Intel 82801CA SMBus Controller (rev. 0x02)
ichsmb0: interrupting at irq 5
iic0 at ichsmb0: I2C bus
auich0 at pci0 dev 31 function 5: i82801CA (ICH3) AC-97 Audio
auich0: interrupting at irq 5
auich0: ac97: Analog Devices AD1881A codec; headphone, Analog Devices Phat Stereo
auich0: ac97: ext id 0x1<VRA>
Intel 82801CA AC'97 Modem Controller (modem communications, revision 0x02) at pci0 dev 31 function 6 not configured
isa0 at ichlpcib0
lpt0 at isa0 port 0x378-0x37b irq 7
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
ieee1394if0: 1 nodes, maxhop <= 0 cable IRM irm(0) (me)
ieee1394if0: bus manager 0
Initializing SSP: d98c769d 601a2090 8f586689 47de461 3af5c426 91cefe8a 830e76c2 a71a35fb 
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
TSC not known invariant on this CPU
timecounter: Timecounter "TSC" frequency 1199062880 Hz quality -100
auich0: measured ac97 link rate at 47294 Hz, will use 48000 Hz
audio0 at auich0: full duplex, playback, capture, mmap, independent
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
acpiacad0: AC adapter online.
acpiacad0: AC adapter connected
uhub0 at usb0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
IPsec: Initialized Security Association Processing.
crypto: assign driver 0, flags 2
crypto: driver 0 registers alg 1 flags 0 maxoplen 0
crypto: driver 0 registers alg 2 flags 0 maxoplen 0
crypto: driver 0 registers alg 3 flags 0 maxoplen 0
crypto: driver 0 registers alg 4 flags 0 maxoplen 0
crypto: driver 0 registers alg 5 flags 0 maxoplen 0
crypto: driver 0 registers alg 26 flags 0 maxoplen 0
crypto: driver 0 registers alg 27 flags 0 maxoplen 0
crypto: driver 0 registers alg 29 flags 0 maxoplen 0
crypto: driver 0 registers alg 33 flags 0 maxoplen 0
crypto: driver 0 registers alg 17 flags 0 maxoplen 0
crypto: driver 0 registers alg 6 flags 0 maxoplen 0
crypto: driver 0 registers alg 19 flags 0 maxoplen 0
crypto: driver 0 registers alg 7 flags 0 maxoplen 0
crypto: driver 0 registers alg 20 flags 0 maxoplen 0
crypto: driver 0 registers alg 15 flags 0 maxoplen 0
crypto: driver 0 registers alg 24 flags 0 maxoplen 0
crypto: driver 0 registers alg 25 flags 0 maxoplen 0
crypto: driver 0 registers alg 8 flags 0 maxoplen 0
crypto: driver 0 registers alg 21 flags 0 maxoplen 0
crypto: driver 0 registers alg 16 flags 0 maxoplen 0
crypto: driver 0 registers alg 9 flags 0 maxoplen 0
crypto: driver 0 registers alg 10 flags 0 maxoplen 0
crypto: driver 0 registers alg 13 flags 0 maxoplen 0
crypto: driver 0 registers alg 14 flags 0 maxoplen 0
crypto: driver 0 registers alg 28 flags 0 maxoplen 0
crypto: driver 0 registers alg 30 flags 0 maxoplen 0
crypto: driver 0 registers alg 31 flags 0 maxoplen 0
crypto: driver 0 registers alg 32 flags 0 maxoplen 0
crypto: driver 0 registers alg 11 flags 0 maxoplen 0
crypto: driver 0 registers alg 18 flags 0 maxoplen 0
crypto: driver 0 registers alg 23 flags 0 maxoplen 0
crypto: driver 0 registers alg 22 flags 0 maxoplen 0
wd0 at atabus0 drive 0
wd0: <HITACHI_DK23DA-20B>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 19077 MB, 41344 cyl, 15 head, 63 sec, 512 bytes/sect x 39070080 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
atapibus0 at atabus1: 2 targets
cd0 at atapibus0 drive 0: <DW-28E, , 2.1A> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
cd0(piixide0:1:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
crypto: assign driver 1, flags 2
crypto: driver 1 registers alg 1 flags 0 maxoplen 0
crypto: driver 1 registers alg 2 flags 0 maxoplen 0
crypto: driver 1 registers alg 3 flags 0 maxoplen 0
crypto: driver 1 registers alg 4 flags 0 maxoplen 0
crypto: driver 1 registers alg 5 flags 0 maxoplen 0
crypto: driver 1 registers alg 26 flags 0 maxoplen 0
crypto: driver 1 registers alg 27 flags 0 maxoplen 0
crypto: driver 1 registers alg 29 flags 0 maxoplen 0
crypto: driver 1 registers alg 33 flags 0 maxoplen 0
crypto: driver 1 registers alg 17 flags 0 maxoplen 0
crypto: driver 1 registers alg 6 flags 0 maxoplen 0
crypto: driver 1 registers alg 19 flags 0 maxoplen 0
crypto: driver 1 registers alg 7 flags 0 maxoplen 0
crypto: driver 1 registers alg 20 flags 0 maxoplen 0
crypto: driver 1 registers alg 15 flags 0 maxoplen 0
crypto: driver 1 registers alg 24 flags 0 maxoplen 0
crypto: driver 1 registers alg 25 flags 0 maxoplen 0
crypto: driver 1 registers alg 8 flags 0 maxoplen 0
crypto: driver 1 registers alg 21 flags 0 maxoplen 0
crypto: driver 1 registers alg 16 flags 0 maxoplen 0
crypto: driver 1 registers alg 9 flags 0 maxoplen 0
crypto: driver 1 registers alg 10 flags 0 maxoplen 0
crypto: driver 1 registers alg 13 flags 0 maxoplen 0
crypto: driver 1 registers alg 14 flags 0 maxoplen 0
crypto: driver 1 registers alg 28 flags 0 maxoplen 0
crypto: driver 1 registers alg 30 flags 0 maxoplen 0
crypto: driver 1 registers alg 31 flags 0 maxoplen 0
crypto: driver 1 registers alg 32 flags 0 maxoplen 0
crypto: driver 1 registers alg 11 flags 0 maxoplen 0
crypto: driver 1 registers alg 18 flags 0 maxoplen 0
crypto: driver 1 registers alg 23 flags 0 maxoplen 0
crypto: driver 1 registers alg 22 flags 0 maxoplen 0
Kernelized RAIDframe activated
Searching for RAID components...
boot device: wd0
root on wd0a dumps on wd0b
mountroot: trying smbfs...
mountroot: trying ntfs...
mountroot: trying nfs...
mountroot: trying msdos...
mountroot: trying lfs...
mountroot: trying ext2fs...
mountroot: trying ffs...
root file system type: ffs
pci_mem_find: void region
pci_mem_find: void region
pci_mem_find: void region
pci_mem_find: void region
radeon0: map 3 failed
pci_mem_find: void region
radeon0: map 4 failed
pci_mem_find: void region
radeon0: map 5 failed
DRM debug in drm_minor_register: 
DRM debug in drm_minor_register: new minor assigned 64
DRM debug in drm_minor_register: 
DRM debug in drm_minor_register: 
DRM debug in drm_minor_register: new minor assigned 0
drm: initializing kernel modesetting (RV200 0x1002:0x4C58 0x1014:0x0518).
drm: register mmio base: 0xd0100000
drm: register mmio size: 65536
pci_io_find: expected type i/o, found mem
DRM error in radeon_get_bios: Unable to locate a BIOS ROM
drm: Using generic clock info
radeon0: info: GTT: 64M 0xE0000000 - 0xE3FFFFFF
radeon0: info: VRAM: 128M 0x00000000E8000000 - 0x00000000EFFFFFFF (64M used)
drm: Detected VRAM RAM=80M, BAR=128M
drm: RAM width 128bits DDR
Zone  kernel: Available graphics memory: 794674 kiB
drm: radeon: 64M of VRAM memory ready
drm: radeon: 64M of GTT memory ready.
radeon0: info: WB disabled
radeon0: info: fence driver on ring 0 use gpu addr 0x00000000e0000000 and cpu addr 0x0xdbbdc000
drm: Supports vblank timestamp caching Rev 2 (21.10.2013).
drm: Driver supports precise vblank timestamp query.
DRM debug in drm_irq_install: irq=9
radeon0: interrupting at irq 9 (radeon)
drm: radeon: irq initialized.
DRM debug in r100_cp_init_microcode: 
drm: Loading R100 Microcode
init: copying out path `/sbin/init' 11
drm: radeon: ring at 0x00000000E0001000
drm: ring test succeeded in 0 usecs
drm: ib test succeeded in 0 usecs
drm: Connector Table: 1 (generic)
drm: No panel info found in BIOS
drm: Panel info derived from registers
drm: Panel Size 1600x1200
drm: No TV DAC info found in BIOS
drm: Radeon Display Connectors
drm: Connector 0:
drm:   LVDS-1
drm:   Encoders:
drm:     LCD1: INTERNAL_LVDS
drm: Connector 1:
drm:   VGA-1
drm:   DDC: 0x60 0x60 0x60 0x60 0x60 0x60 0x60 0x60
drm:   Encoders:
drm:     CRT1: INTERNAL_DAC1
drm: Connector 2:
drm:   SVIDEO-1
drm:   Encoders:
drm:     TV1: INTERNAL_DAC2
DRM debug in radeon_legacy_lvds_dpms: 
DRM debug in radeon_legacy_lvds_update: 
DRM debug in radeon_legacy_primary_dac_dpms: 
DRM debug in radeon_legacy_tv_dac_dpms: 
DRM debug in drm_vblank_get: enabling vblank on crtc 0, ret: 0
DRM debug in drm_calc_vbltimestamp_from_scanoutpos: crtc 0: Noop due to uninitialized mode.
DRM debug in drm_update_vblank_count: enabling vblank interrupts on crtc 0, missed 12396
DRM debug in drm_calc_vbltimestamp_from_scanoutpos: crtc 0: Noop due to uninitialized mode.
DRM debug in drm_vblank_get: enabling vblank on crtc 1, ret: 0
DRM debug in drm_calc_vbltimestamp_from_scanoutpos: crtc 1: Noop due to uninitialized mode.
DRM debug in drm_update_vblank_count: enabling vblank interrupts on crtc 1, missed 0
DRM debug in drm_helper_probe_single_connector_modes: [CONNECTOR:18:LVDS-1]
DRM debug in radeon_combios_connected_scratch_regs: LCD1 connected
DRM debug in radeon_fp_native_mode: Adding cvt approximation of native panel mode 1600x1200
DRM debug in drm_helper_probe_single_connector_modes: [CONNECTOR:18:LVDS-1] probed modes :
DRM debug in drm_mode_debug_printmodeline: Modeline 23:"1600x1200" 60 130250 1600 1648 1680 1760 1200 1203 1207 1235 0x48 0x9
DRM debug in drm_mode_debug_printmodeline: Modeline 36:"1400x1050" 60 121750 1400 1488 1632 1864 1050 1053 1057 1089 0x0 0x6
DRM debug in drm_mode_debug_printmodeline: Modeline 34:"1280x1024" 60 109000 1280 1368 1496 1712 1024 1027 1034 1063 0x0 0x6
DRM debug in drm_mode_debug_printmodeline: Modeline 35:"1440x900" 60 106500 1440 1528 1672 1904 900 903 909 934 0x0 0x6
DRM debug in drm_mode_debug_printmodeline: Modeline 33:"1280x960" 60 101250 1280 1360 1488 1696 960 963 967 996 0x0 0x6
DRM debug in drm_mode_debug_printmodeline: Modeline 32:"1280x854" 60 89250 1280 1352 1480 1680 854 857 867 887 0x0 0x6
DRM debug in drm_mode_debug_printmodeline: Modeline 31:"1280x800" 60 83500 1280 1352 1480 1680 800 803 809 831 0x0 0x6
DRM debug in drm_mode_debug_printmodeline: Modeline 30:"1280x720" 60 74500 1280 1344 1472 1664 720 723 728 748 0x0 0x6
DRM debug in drm_mode_debug_printmodeline: Modeline 29:"1152x768" 60 71750 1152 1216 1328 1504 768 771 781 798 0x0 0x6
DRM debug in drm_mode_debug_printmodeline: Modeline 28:"1024x768" 60 63500 1024 1072 1176 1328 768 771 775 798 0x0 0x6
DRM debug in drm_mode_debug_printmodeline: Modeline 26:"800x600" 60 38250 800 832 912 1024 600 603 607 624 0x0 0x6
DRM debug in drm_mode_debug_printmodeline: Modeline 27:"848x480" 60 31500 848 872 952 1056 480 483 493 500 0x0 0x6
DRM debug in drm_mode_debug_printmodeline: Modeline 25:"720x480" 60 26750 720 744 808 896 480 483 493 500 0x0 0x6
DRM debug in drm_mode_debug_printmodeline: Modeline 24:"640x480" 59 23750 640 664 720 800 480 483 487 500 0x0 0x6
DRM debug in drm_helper_probe_single_connector_modes: [CONNECTOR:20:VGA-1]
DRM debug in radeon_combios_connected_scratch_regs: CRT1 disconnected
DRM debug in drm_helper_probe_single_connector_modes: [CONNECTOR:20:VGA-1] disconnected
DRM debug in drm_helper_probe_single_connector_modes: [CONNECTOR:22:SVIDEO-1]
DRM debug in radeon_combios_connected_scratch_regs: TV1 disconnected
DRM debug in drm_helper_probe_single_connector_modes: [CONNECTOR:22:SVIDEO-1] disconnected
DRM debug in drm_setup_crtcs: 
DRM debug in drm_enable_connectors: connector 18 enabled? yes
DRM debug in drm_enable_connectors: connector 20 enabled? no
DRM debug in drm_enable_connectors: connector 22 enabled? no
DRM debug in drm_target_preferred: looking for cmdline mode on connector 18
DRM debug in drm_target_preferred: looking for preferred mode on connector 18
DRM debug in drm_target_preferred: found mode 1600x1200
DRM debug in drm_setup_crtcs: picking CRTCs for 4096x4096 config
DRM debug in drm_setup_crtcs: desired mode 1600x1200 set on crtc 14
DRM debug in drm_framebuffer_reference: FB ID: 38
radeondrmkmsfb0 at radeon0
radeondrmkmsfb0: WARNING: power management not supported
radeon0: info: registered panic notifier
radeondrmkmsfb0: framebuffer at 0xdbde3000, size 1600x1200, depth 32, stride 6400
DRM debug in drm_crtc_helper_set_config: 
DRM debug in drm_crtc_helper_set_config: [CRTC:14] [FB:38] #connectors=1 (x y) (0 0)
DRM debug in drm_crtc_helper_set_config: crtc has no fb, full mode set
DRM debug in drm_crtc_helper_set_config: modes are different, full mode set
DRM debug in drm_mode_debug_printmodeline: Modeline 0:"" 0 0 0 0 0 0 0 0 0 0 0x0 0x0
DRM debug in drm_mode_debug_printmodeline: Modeline 37:"1600x1200" 60 130250 1600 1648 1680 1760 1200 1203 1207 1235 0x48 0x9
DRM debug in drm_crtc_helper_set_config: encoder changed, full mode switch
DRM debug in drm_crtc_helper_set_config: crtc changed, full mode switch
DRM debug in drm_crtc_helper_set_config: [CONNECTOR:18:LVDS-1] to [CRTC:14]
DRM debug in drm_crtc_helper_set_config: attempting to set mode from userspace
DRM debug in drm_mode_debug_printmodeline: Modeline 37:"1600x1200" 60 130250 1600 1648 1680 1760 1200 1203 1207 1235 0x48 0x9
DRM debug in radeon_encoder_set_active_device: setting active device to 00000002 from 00000002 00000002 for encoder 3
DRM debug in drm_crtc_helper_set_mode: [CRTC:14]
DRM debug in radeon_legacy_lvds_dpms: 
DRM debug in radeon_legacy_lvds_update: 
DRM debug in radeon_legacy_primary_dac_dpms: 
DRM debug in radeon_legacy_tv_dac_dpms: 
DRM debug in radeon_crtc_do_set_base: 
DRM debug in r100_bandwidth_update: GRPH_BUFFER_CNTL from to 201e5c5c
DRM debug in radeon_set_crtc_timing: 
DRM debug in radeon_set_pll: 
DRM debug in drm_crtc_helper_set_mode: [ENCODER:17:LVDS-17] set [MODE:37:1600x1200]
DRM debug in radeon_legacy_lvds_mode_set: 
DRM debug in radeon_legacy_lvds_mode_set: bios LVDS_GEN_CNTL: 0x80dffa5
DRM debug in radeon_legacy_lvds_dpms: DRM debug in drm_calc_vbltimestamp_from_scanoutpos: crtc 0: Noop due to uninitialized mode.

DRM debug in radeon_legacy_lvds_update: 
DRM error in drm_calc_timestamping_constants: crtc 14: Can't calculate constants, dotclock = 0!
DRM debug in drm_calc_timestamping_constants: crtc 14: hwmode: htotal 0, vtotal 0, vdisplay 1200
DRM debug in drm_calc_timestamping_constants: crtc 14: clock 0 kHz framedur 0 linedur 0, pixeldur 0
DRM debug in drm_crtc_helper_set_config: Setting connector DPMS state to on
DRM debug in drm_crtc_helper_set_config: 	[CONNECTOR:18:LVDS-1] set DPMS on
DRM debug in radeon_legacy_primary_dac_dpms: 
DRM debug in radeon_legacy_tv_dac_dpms: 
DRM debug in drm_framebuffer_reference: FB ID: 38
DRM debug in drm_crtc_helper_set_config: 
DRM debug in drm_crtc_helper_set_config: [CRTC:16] [NOFB]
DRM debug in radeon_legacy_primary_dac_dpms: 
DRM debug in radeon_legacy_tv_dac_dpms: 
DRM debug in drm_framebuffer_reference: FB ID: 38
DRM debug in drm_framebuffer_unreference: FB ID: 38
wsdisplay0 at radeondrmkmsfb0 kbdmux 1: console (default, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
DRM debug in vblank_disable_fn: disabling vblank on crtc 0
DRM debug in drm_calc_vbltimestamp_from_scanoutpos: crtc 0: Noop due to uninitialized mode.
fxp0: link state UP (was UNKNOWN)
fxp0: link state DOWN (was UP)
fxp0: link state UP (was DOWN)
fxp0: link state DOWN (was UP)
fxp0: link state UP (was DOWN)
acpibat0: state changed on 'charge state' to 'CRITICAL'
wsdisplay0: screen 1 added (default, vt100 emulation)
wsdisplay0: screen 2 added (default, vt100 emulation)
wsdisplay0: screen 3 added (default, vt100 emulation)
wsdisplay0: screen 4 added (default, vt100 emulation)
fxp0: link state DOWN (was UP)
fxp0: link state UP (was DOWN)

-- 
|/"\ John D. Baker, KN5UKS               NetBSD     Darwin/MacOS X
|\ / jdbaker[snail]mylinuxisp[flyspeck]com    OpenBSD            FreeBSD
| X  No HTML/proprietary data in email.   BSD just sits there and works!
|/ \ GPGkeyID:  D703 4A7E 479F 63F8 D3F4  BD99 9572 8F23 E4AD 1645



Home | Main Index | Thread Index | Old Index