I have a machine with a Tyan Tiger MP S2460 Dual Athlon motherboard
which I would like to run an MP NetBSD kernel on.  The machine has a
ZNYX four-port Ethernet card which works fine when I boot a non-MP
kernel, but when I boot an MP kernel built from the
i386mp_plus16_stable tag, I see the messages

  pci_intr_map: no MP mapping found
  isa_intr_establish: no MP mapping found

for each of the four ports and the card does not work.

Any ideas how this can be fixed?  Full dmesg output follows.
-- 
Andreas Gustafsson, gson@gson.org

NetBSD 1.6_BETA4 (GUAVAMP) #3: Thu Jul 25 19:59:49 PDT 2002
    gson@guava.araneus.fi:/usr/src/sys-1.6/sys/arch/i386/compile/GUAVAMP
total memory = 511 MB
avail memory = 462 MB
using 6144 buffers containing 26292 KB of memory
BIOS32 rev. 0 found at 0xfd6c0
PCI BIOS rev. 2.1 found at 0xfd7e0
pcibios: config mechanism [1][x], special cycles [x][x], last bus 2
PCI IRQ Routing Table rev. 1.0 found at 0xfdf10, size 0 bytes (-2 entries)
pcibios_pir_init: bad IRQ table size
PCI BIOS has 11 Interrupt Routing table entries
PIR Entry 0:
	Bus: 0  Device: 8
		INTA: link 0x01 bitmap 0xdef8
		INTB: link 0x02 bitmap 0xdef8
		INTC: link 0x03 bitmap 0xdef8
		INTD: link 0x04 bitmap 0xdef8
PIR Entry 1:
	Bus: 0  Device: 9
		INTA: link 0x02 bitmap 0xdef8
		INTB: link 0x03 bitmap 0xdef8
		INTC: link 0x04 bitmap 0xdef8
		INTD: link 0x01 bitmap 0xdef8
PIR Entry 2:
	Bus: 0  Device: 10
		INTA: link 0x03 bitmap 0xdef8
		INTB: link 0x04 bitmap 0xdef8
		INTC: link 0x01 bitmap 0xdef8
		INTD: link 0x02 bitmap 0xdef8
PIR Entry 3:
	Bus: 0  Device: 11
		INTA: link 0x04 bitmap 0xdef8
		INTB: link 0x01 bitmap 0xdef8
		INTC: link 0x02 bitmap 0xdef8
		INTD: link 0x03 bitmap 0xdef8
PIR Entry 4:
	Bus: 0  Device: 12
		INTA: link 0x01 bitmap 0xdef8
		INTB: link 0x02 bitmap 0xdef8
		INTC: link 0x03 bitmap 0xdef8
		INTD: link 0x04 bitmap 0xdef8
PIR Entry 5:
	Bus: 0  Device: 13
		INTA: link 0x02 bitmap 0xdef8
		INTB: link 0x03 bitmap 0xdef8
		INTC: link 0x04 bitmap 0xdef8
		INTD: link 0x01 bitmap 0xdef8
PIR Entry 6:
	Bus: 0  Device: 14
		INTA: link 0x04 bitmap 0xdef8
		INTB: link 0x00 bitmap 0xdef8
		INTC: link 0x00 bitmap 0xdef8
		INTD: link 0x00 bitmap 0xdef8
PIR Entry 7:
	Bus: 0  Device: 0
		INTA: link 0x00 bitmap 0xdef8
		INTB: link 0x00 bitmap 0xdef8
		INTC: link 0x00 bitmap 0xdef8
		INTD: link 0x00 bitmap 0xdef8
PIR Entry 8:
	Bus: 0  Device: 1
		INTA: link 0x02 bitmap 0xdef8
		INTB: link 0x03 bitmap 0xdef8
		INTC: link 0x00 bitmap 0xdef8
		INTD: link 0x00 bitmap 0xdef8
PIR Entry 9:
	Bus: 0  Device: 7
		INTA: link 0x01 bitmap 0xdef8
		INTB: link 0x02 bitmap 0xdef8
		INTC: link 0x03 bitmap 0xdef8
		INTD: link 0x04 bitmap 0xdef8
PIR Entry 10:
	Bus: 1  Device: 5
		INTA: link 0x03 bitmap 0xdef8
		INTB: link 0x04 bitmap 0xdef8
		INTC: link 0x00 bitmap 0xdef8
		INTD: link 0x00 bitmap 0xdef8
pci_intr_fixup: no compatible PCI ICU found
Warning: unable to fix up PCI interrupt routing
PCI fixup examining 1022:700c
PCI fixup examining 1022:700d
PCI fixup examining 102b:521
PCI bridge 0: primary 0, secondary 1, subordinate 1
PCI fixup examining 1022:7410
PCI fixup examining 1022:7411
PCI fixup examining 1022:7413
PCI fixup examining 1022:7414
PCI fixup examining 104c:ac50
PCI bridge 1: primary 0, secondary 2, subordinate 2
PCI fixup examining 1011:24
PCI fixup examining 1011:09
PCI fixup examining 1011:09
PCI fixup examining 1011:09
PCI fixup examining 1011:09
PCI bridge 2: primary 0, secondary 3, subordinate 3
PCI fixup examining 1274:5000
PCI fixup examining 1000:01
PCI bus #3 is the last bus
mainbus0 (root)
mainbus0: scanning 0x9f800 to 0x9fbf0 for MP signature
mainbus0: scanning 0x9f400 to 0x9f7f0 for MP signature
mainbus0: scanning 0xf0000 to 0xffff0 for MP signature
mainbus0: MP floating pointer found in bios at 0xf7510
mainbus0: MP config table at 0x9fc70, 296 bytes long
mainbus0: Intel MP Specification (Version 1.4) (TYAN     GUINNESS    )
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: AMD Athlon Model 4 (Thunderbird) (686-class), 1200.12 MHz
cpu0: features 183fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu0: features 183fbff<PGE,MCA,CMOV,FGPAT,PSE36,MMX>
cpu0: features 183fbff<FXSR>
cpu0: I-cache 64 KB 64b/line 2-way, D-cache 64 KB 64b/line 2-way
cpu0: L2 cache 256 KB 64b/line 16-way
cpu0: ITLB 16 4 KB entries fully associative, 8 4 MB entries fully associative
cpu0: DTLB 24 4 KB entries fully associative, 8 4 MB entries 4-way
cpu0: calibrating local timer
cpu0: apic clock running at 266 MHz
cpu0: 8 page colors
cpu0: kstack at 0xe32f0000 for 8192 bytes
cpu0: idle pcb at 0xe32f0000, idle sp at 0xe32f1f98
mpbios: bus 0 is type PCI   
mpbios: bus 1 is type PCI   
mpbios: bus 2 is type PCI   
mpbios: bus 3 is type ISA   
ioapic0 at mainbus0 apid 1 (I/O APIC)
ioapic0: pa 0xfec00000, virtual wire mode, version 11, 24 pins
ioapic0: int0 attached to ExtINT (type 3<type=3=ExtINT> flags 5<pol=1=Act Hi,trig=1=Edge>)
ioapic0: int1 attached to isa0 irq 1 (type 0<type=0> flags 5<pol=1=Act Hi,trig=1=Edge>)
ioapic0: int2 attached to isa0 irq 0 (type 0<type=0> flags 5<pol=1=Act Hi,trig=1=Edge>)
ioapic0: int3 attached to isa0 irq 3 (type 0<type=0> flags 5<pol=1=Act Hi,trig=1=Edge>)
ioapic0: int4 attached to isa0 irq 4 (type 0<type=0> flags 5<pol=1=Act Hi,trig=1=Edge>)
ioapic0: int5 attached to isa0 irq 5 (type 0<type=0> flags 5<pol=1=Act Hi,trig=1=Edge>)
ioapic0: int6 attached to isa0 irq 6 (type 0<type=0> flags 5<pol=1=Act Hi,trig=1=Edge>)
ioapic0: int7 attached to isa0 irq 7 (type 0<type=0> flags 5<pol=1=Act Hi,trig=1=Edge>)
ioapic0: int8 attached to isa0 irq 8 (type 0<type=0> flags 5<pol=1=Act Hi,trig=1=Edge>)
ioapic0: int9 attached to isa0 irq 9 (type 0<type=0> flags 5<pol=1=Act Hi,trig=1=Edge>)
ioapic0: int18 attached to pci2 device 4 INT_A (type 0<type=0> flags f<pol=3=Act Lo,trig=3=Level>)
ioapic0: int19 attached to pci0 device 7 INT_D (type 0<type=0> flags f<pol=3=Act Lo,trig=3=Level>)
ioapic0: int12 attached to isa0 irq 12 (type 0<type=0> flags 5<pol=1=Act Hi,trig=1=Edge>)
ioapic0: int13 attached to isa0 irq 13 (type 0<type=0> flags 5<pol=1=Act Hi,trig=1=Edge>)
ioapic0: int14 attached to isa0 irq 14 (type 0<type=0> flags 5<pol=1=Act Hi,trig=1=Edge>)
ioapic0: int15 attached to isa0 irq 15 (type 0<type=0> flags 5<pol=1=Act Hi,trig=1=Edge>)
ioapic0: int19 attached to pci2 device 5 INT_A (type 0<type=0> flags f<pol=3=Act Lo,trig=3=Level>)
ioapic0: int16 attached to pci2 device 6 INT_A (type 0<type=0> flags f<pol=3=Act Lo,trig=3=Level>)
ioapic0: int17 attached to pci2 device 7 INT_A (type 0<type=0> flags f<pol=3=Act Lo,trig=3=Level>)
ioapic0: int19 attached to pci0 device 11 INT_A (type 0<type=0> flags f<pol=3=Act Lo,trig=3=Level>)
ioapic0: int16 attached to pci0 device 12 INT_A (type 0<type=0> flags f<pol=3=Act Lo,trig=3=Level>)
ioapic0: int18 attached to pci1 device 5 INT_A (type 0<type=0> flags f<pol=3=Act Lo,trig=3=Level>)
local apic: int0 attached to ExtINT (type 3<type=3=ExtINT> flags 5<pol=1=Act Hi,trig=1=Edge>)
local apic: int1 attached to NMI (type 1<type=1=NMI> flags 5<pol=1=Act Hi,trig=1=Edge>)
mainbus0: MP WARNING: 344 bytes of extended entries not examined
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: Advanced Micro Devices AMD762 NorthBridge (rev. 0x11)
agp0 at pchb0: aperture at 0xf8000000, size 0x4000000
ppb0 at pci0 dev 1 function 0: Advanced Micro Devices AMD762 AGP Bridge (rev. 0x00)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
vga1 at pci1 dev 5 function 0: Matrox MGA G200 AGP (rev. 0x01)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
pcib0 at pci0 dev 7 function 0
pcib0: Advanced Micro Devices AMD766 SouthBridge (rev. 0x02)
pciide0 at pci0 dev 7 function 1: Advanced Micro Devices AMD766 IDE Controller (rev. 0x01)
pciide0: bus-master DMA support present
pciide0: primary channel configured to compatibility mode
wd0 at pciide0 channel 0 drive 0: <IBM-DTLA-307030>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 29314 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 60036480 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
pciide0: primary channel interrupting at irq 14
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA data transfers)
pciide0: secondary channel configured to compatibility mode
pciide0: disabling secondary channel (no drives)
Advanced Micro Devices AMD766 Power Management Controller (miscellaneous bridge, revision 0x01) at pci0 dev 7 function 3 not configured
ohci0 at pci0 dev 7 function 4: Advanced Micro Devices AMD766 USB Host Controller (rev. 0x07)
ohci0: interrupting at apic 1 int 19 (irq 11)
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: Advanced Micro OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 4 ports with 4 removable, self powered
cbb0 at pci0 dev 8 function 0: Texas Instruments PCI1410 PCI-CardBus Bridge (rev. 0x01)
cbb0: NOT USED because of unconfigured interrupt
ppb1 at pci0 dev 10 function 0: Digital Equipment DECchip 21152 PCI-PCI Bridge (rev. 0x03)
pci2 at ppb1 bus 3
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
tlp0 at pci2 dev 4 function 0: DECchip 21140A Ethernet, pass 2.2
pci_intr_map: bus 3 dev 4 func 0 pin 1; line 10
pci_intr_map: no MP mapping found
isa_intr_establish: no MP mapping found
tlp0: interrupting at irq 10
tlp0: Ethernet address 00:c0:95:e0:47:b8
tlp0: 10baseT, 100baseTX
tlp1 at pci2 dev 5 function 0: DECchip 21140A Ethernet, pass 2.2
pci_intr_map: bus 3 dev 5 func 0 pin 2; line 11
pci_intr_map: no MP mapping found
isa_intr_establish: no MP mapping found
tlp1: interrupting at irq 11
tlp1: Ethernet address 00:c0:95:e0:47:b9
tlp1: 10baseT, 100baseTX
tlp2 at pci2 dev 6 function 0: DECchip 21140A Ethernet, pass 2.2
pci_intr_map: bus 3 dev 6 func 0 pin 3; line 11
pci_intr_map: no MP mapping found
isa_intr_establish: no MP mapping found
tlp2: interrupting at irq 11
tlp2: Ethernet address 00:c0:95:e0:47:ba
tlp2: 10baseT, 100baseTX
tlp3 at pci2 dev 7 function 0: DECchip 21140A Ethernet, pass 2.2
pci_intr_map: bus 3 dev 7 func 0 pin 4; line 11
pci_intr_map: no MP mapping found
isa_intr_establish: no MP mapping found
tlp3: interrupting at irq 11
tlp3: Ethernet address 00:c0:95:e0:47:bb
tlp3: 10baseT, 100baseTX
eap0 at pci0 dev 11 function 0: Ensoniq AudioPCI (rev. 0x00)
eap0: interrupting at apic 1 int 19 (irq 11)
audio0 at eap0: full duplex, mmap, independent
midi0 at eap0: AudioPCI MIDI UART
siop0 at pci0 dev 12 function 0: Symbios Logic 53c810 (fast scsi)
siop0: interrupting at apic 1 int 16 (irq 11)
scsibus0 at siop0: 8 targets, 8 luns per target
isa0 at pcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi1 at pcppi0: PC speaker
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff: using exception 16
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
isapnp0: no ISA Plug 'n Play devices found
biomask f3ff netmask ffff ttymask ffff
cpu0: prelint0 700<vector=0,delmode=7,dest=0> 0<target=0>
cpu0: prelint1 400<vector=0,delmode=4,dest=0> 0<target=0>
cpu0: timer0 300d0<vector=d0,delmode=0,masked,dest=0> 0<target=0>
cpu0: pcint0 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
cpu0: lint0 10700<vector=0,delmode=7,masked,dest=0> 0<target=0>
cpu0: lint1 400<vector=0,delmode=4,dest=0> 0<target=0>
cpu0: err0 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
ioapic0: enabling
ioapic0: int0 10700<vector=0,delmode=7,masked,dest=0> 0<target=0>
ioapic0: int1 1a0<vector=a0,delmode=1,dest=0> 0<target=0>
ioapic0: int2 10100<vector=0,delmode=1,masked,dest=0> 0<target=0>
ioapic0: int3 1e1<vector=e1,delmode=1,dest=0> 0<target=0>
ioapic0: int4 1e2<vector=e2,delmode=1,dest=0> 0<target=0>
ioapic0: int5 10100<vector=0,delmode=1,masked,dest=0> 0<target=0>
ioapic0: int6 170<vector=70,delmode=1,dest=0> 0<target=0>
ioapic0: int7 10100<vector=0,delmode=1,masked,dest=0> 0<target=0>
ioapic0: int8 10100<vector=0,delmode=1,masked,dest=0> 0<target=0>
ioapic0: int9 10100<vector=0,delmode=1,masked,dest=0> 0<target=0>
ioapic0: int10 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
ioapic0: int11 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
ioapic0: int12 10100<vector=0,delmode=1,masked,dest=0> 0<target=0>
ioapic0: int13 10100<vector=0,delmode=1,masked,dest=0> 0<target=0>
ioapic0: int14 171<vector=71,delmode=1,dest=0> 0<target=0>
ioapic0: int15 10100<vector=0,delmode=1,masked,dest=0> 0<target=0>
ioapic0: int16 a172<vector=72,delmode=1,actlo,level,dest=0> 0<target=0>
ioapic0: int17 1a100<vector=0,delmode=1,actlo,level,masked,dest=0> 0<target=0>
ioapic0: int18 1a100<vector=0,delmode=1,actlo,level,masked,dest=0> 0<target=0>
ioapic0: WARNING: sharing interrupt between different IPLs (currently broken)
ioapic0: pin 19, ipls 70..c0
ioapic0: int19 a173<vector=73,delmode=1,actlo,level,dest=0> 0<target=0>
ioapic0: int20 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
ioapic0: int21 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
ioapic0: int22 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
ioapic0: int23 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
scsibus0: waiting 2 seconds for devices to settle...
cd0 at scsibus0 target 4 lun 0: <RICOH, MP6200S, 2.20> SCSI2 5/cdrom removable
cd0: async, 8-bit transfers
Kernelized RAIDframe activated

pool_get(PR_WAITOK) with held simple_lock 0xc0659778 CPU 0 /usr/src/sys-1.6/sys/arch/i386/compile/GUAVAMP/../../../../kern/vfs_subr.c:460
pool_get(c06a7e60,2,15f,c028b29c,0) at pool_get+0x57
uvm_map(c067d180,c073abec,1000,c067d080,23b63000,0,0,1727) at uvm_map+0x89e
uvm_km_kmemalloc(c067d180,c067d080,1000,1,0) at uvm_km_kmemalloc+0x6d
uvm_km_alloc_poolpage1(c067d180,c067d080,0,4,c0696620) at uvm_km_alloc_poolpage1+0x3d
pool_page_alloc_nointr(c0699b60,0,c073ac80,c028b65c) at pool_page_alloc_nointr+0x23
pool_allocator_alloc(c0699b60,0,c073acd0,c0299d46,c0699bcc) at pool_allocator_alloc+0x1f
pool_get(c0699b60,0,1cc,c0365e03,c04a6796) at pool_get+0x1eb
getnewvnode(0,0,c135f400,c073ad3c) at getnewvnode+0xbf
getdevvp(3,c073ada8,3,0,c13f0f58) at getdevvp+0x2f
bdevvp(3,c073ada8,c073ada0,c028b65c) at bdevvp+0x16
rf_find_raid_components(c0653338,c0696420,c0696628,c02a2aff,c0653330,c0696420,c0696628,41727,4a0,4a0,c073afa0,c02816fa,8,c0696420,c073afa0,c02816c5,c0738010,738000,73f000,0,0,0,0,c010030c,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0) at rf_find_raid_components+0x10a
raidattach(8,c0696420,c073afa0,c02816c5) at raidattach+0x2ed
main(0,0,0,0,0) at main+0x3b2
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
IP Filter: v3.4.27 initialized.  Default = pass all, Logging = enabled
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
tlp0: filter setup and transmit timeout
tlp1: filter setup and transmit timeout
tlp0: filter setup and transmit timeout
tlp1: filter setup and transmit timeout
tlp0: filter setup and transmit timeout
tlp1: filter setup and transmit timeout
tlp0: filter setup and transmit timeout
tlp1: filter setup and transmit timeout
tlp0: filter setup and transmit timeout
tlp1: filter setup and transmit timeout
tlp0: filter setup and transmit timeout
tlp1: filter setup and transmit timeout
tlp1: filter setup and transmit timeout
tlp1: filter setup and transmit timeout
tlp0: filter setup and transmit timeout
tlp1: filter setup and transmit timeout