Subject: pci_intr_map: no MP mapping found
To: None <tech-smp@netbsd.org>
From: Murray Armfield <murray.armfield@arconsulting.com.au>
List: tech-smp
Date: 05/03/2002 00:53:41
Hi Folks,
	Just pulled down most current (at time of writing) i386 smp branch and tried 
running it for the first time on a single processor AMD A7M266-D motherboard. 
Boots multi-user, seems good however my network card doesn't work.
	I searched and found previous suggestion of "'PCI intr mappings in MP table' 
in the BIOS setup" from Frank, but no option in BIOS and BIOS is current. Am 
I stuffed?

BTW, if apm is not good, shouldn't it be commented out of GENERIC.

dmesg follows FWIW.

NetBSD 1.5ZC (GENERIC.MPDEBUG) #0: Fri May  3 00:19:56 EST 2002
    
admin@enterprise.home.river-styx.org:/usr/src/sys/arch/i386.mp/compile/GENERIC.MPDEBUG
total memory = 1023 MB
avail memory = 932 MB
using 6144 buffers containing 52504 KB of memory
BIOS32 rev. 0 found at 0xf0be0
mainbus0 (root)
mainbus0: scanning 0x9fc00 to 0x9fff0 for MP signature
mainbus0: scanning 0x9f800 to 0x9fbf0 for MP signature
mainbus0: scanning 0xf0000 to 0xffff0 for MP signature
mainbus0: MP floating pointer found in bios at 0xf6d10
mainbus0: MP config table at 0xf6900, 280 bytes long
mainbus0: Intel MP Specification (Version 1.4) (ASUS     PROD00000000)
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: AMD Athlon Model 6 (Palomino) (686-class), 1400.12 MHz
cpu0: features 383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu0: features 383fbff<PGE,MCA,CMOV,FGPAT,PSE36,MMX>
cpu0: features 383fbff<FXSR,SSE>
cpu0: I-cache 64 KB 64b/line 2-way, D-cache 64 KB 64b/line 2-way
cpu0: L2 cache 256 KB 64b/line 16-way
cpu0: ITLB 16 4 KB entries fully associative, 8 4 MB entries fully associative
cpu0: DTLB 32 4 KB entries fully associative, 8 4 MB entries 4-way
cpu0: calibrating local timer
cpu0: apic clock running at 266 MHz
cpu0: 8 page colors
cpu0: kstack at 0xe409d000 for 8192 bytes
cpu0: idle pcb at 0xe409d000, idle sp at 0xe409ef98
mpbios: bus 0 is type PCI
mpbios: bus 1 is type PCI
mpbios: bus 2 is type PCI
mpbios: bus 3 is type ISA
ioapic0 at mainbus0 apid 2 (I/O APIC)
ioapic0: pa 0xfec00000, virtual wire mode, version 11, 24 pins
ioapic0: int16 attached to pci1 device 5 INT_A (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
mpbios: can't find ioapic 4
ioapic0: int19 attached to pci2 device 0 INT_A (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: int17 attached to pci2 device 4 INT_A (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: int18 attached to pci2 device 5 INT_A (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: int19 attached to pci2 device 5 INT_B (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: int16 attached to pci2 device 5 INT_C (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: int17 attached to pci2 device 6 INT_A (type 0<type=0> flags 
f<pol=3=Act Lo,trig=3=Level>)
ioapic0: int0 attached to ExtINT (type 3<type=3=ExtINT> flags 0<pol=0,trig=0>)
ioapic0: int1 attached to isa0 irq 1 (type 0<type=0> flags 0<pol=0,trig=0>)
ioapic0: int2 attached to isa0 irq 0 (type 0<type=0> flags 0<pol=0,trig=0>)
ioapic0: int3 attached to isa0 irq 3 (type 0<type=0> flags 0<pol=0,trig=0>)
ioapic0: int4 attached to isa0 irq 4 (type 0<type=0> flags 0<pol=0,trig=0>)
ioapic0: int6 attached to isa0 irq 6 (type 0<type=0> flags 0<pol=0,trig=0>)
ioapic0: int7 attached to isa0 irq 7 (type 0<type=0> flags 0<pol=0,trig=0>)
ioapic0: int8 attached to isa0 irq 8 (type 0<type=0> flags 0<pol=0,trig=0>)
ioapic0: int12 attached to isa0 irq 12 (type 0<type=0> flags 0<pol=0,trig=0>)
ioapic0: int13 attached to isa0 irq 13 (type 0<type=0> flags 0<pol=0,trig=0>)
ioapic0: int14 attached to isa0 irq 14 (type 0<type=0> flags 0<pol=0,trig=0>)
ioapic0: int15 attached to isa0 irq 15 (type 0<type=0> flags 0<pol=0,trig=0>)
local apic: int0 attached to ExtINT (type 3<type=3=ExtINT> flags 5<pol=1=Act 
Hi,trig=1=Edge>)
local apic: int1 attached to NMI (type 1<type=1=NMI> flags 5<pol=1=Act 
Hi,trig=1=Edge>)
mainbus0: MP WARNING: 124 bytes of extended entries not examined
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: Advanced Micro Devices AMD762 NorthBridge (rev. 0x11)
agp0 at pchb0: aperture at 0xf8000000, size 0x4000000
ppb0 at pci0 dev 1 function 0: Advanced Micro Devices AMD762 AGP Bridge (rev. 
0x00)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
vga1 at pci1 dev 5 function 0: Nvidia Corporation GeForce2 MX [NV11] (rev. 
0xb2)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
pcib0 at pci0 dev 7 function 0
pcib0: Advanced Micro Devices AMD768 PCI to ISA/LPC Bridge (rev. 0x04)
pciide0 at pci0 dev 7 function 1: Advanced Micro Devices AMD768 IDE 
Controller (rev. 0x04)
pciide0: bus-master DMA support present
pciide0: primary channel configured to compatibility mode
wd0 at pciide0 channel 0 drive 0: <ST360021A>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 57241 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 117231408 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd1 at pciide0 channel 0 drive 1: <ST360021A>
wd1: drive supports 16-sector PIO transfers, LBA addressing
wd1: 57241 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 117231408 sectors
wd1: 32-bit data port
wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
pciide0: primary channel interrupting at irq 14
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA 
data transfers)
wd1(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA 
data transfers)
pciide0: secondary channel configured to compatibility mode
atapibus0 at pciide0 channel 1: 2 targets
cd0 at atapibus0 drive 0: <SAMSUNG CD-R/RW DRIVE SW-224B, , VE002R1> type 5 
cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2
pciide0: secondary channel interrupting at irq 15
cd0(pciide0:1:0): using PIO mode 4, DMA mode 2 (using DMA data transfers)
Advanced Micro Devices AMD768 Power Management Controller (miscellaneous 
bridge, revision 0x03) at pci0 dev 7 function 3 not configured
ppb1 at pci0 dev 16 function 0: Advanced Micro Devices AMD768 PCI to PCI 
Bridge (rev. 0x04)
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled
cmpci0 at pci2 dev 4 function 0: C-Media Electronics Inc CMI8738/C3DX PCI 
Audio Device (rev. 0x10)
cmpci0: interrupting at apic 2 int 17 (irq 10)
audio0 at cmpci0: full duplex, mmap, independent
opl0 at cmpci0: model OPL3: LR swapped
midi0 at opl0: CMPCI Yamaha OPL3
mpu0 at cmpci0
midi1 at mpu0: CMPCI MPU-401 MIDI UART
ohci0 at pci2 dev 5 function 0: NEC USB Host Controller (rev. 0x41)
ohci0: interrupting at apic 2 int 19 (irq 5)
ohci0: OHCI version 1.0
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: NEC OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
ohci1 at pci2 dev 5 function 1: NEC USB Host Controller (rev. 0x41)
ohci1: interrupting at apic 2 int 16 (irq 9)
ohci1: OHCI version 1.0
usb1 at ohci1: USB revision 1.0
uhub1 at usb1
uhub1: NEC OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
NEC USB Host Controller (USB serial bus, interface 0x20, revision 0x02) at 
pci2 dev 5 function 2 not configured
ex0 at pci2 dev 6 function 0: 3Com 3c905C-TX 10/100 Ethernet with mngmt (rev. 
0x78)
pci_intr_map: bus 2 dev 6 func 0 pin 3; line 10
pci_intr_map: no MP mapping found
isa_intr_establish: no MP mapping found
ex0: interrupting at irq 10
ex0: MAC address 00:04:75:8a:4a:32
exphy0 at ex0 phy 24: 3Com internal media interface
exphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isa0 at pcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
lptprobe: mask ff data 55 failed
lptprobe: mask ff data 55 failed
lpt2 at isa0 port 0x3bc-0x3bf irq : polled
seaprobe: board type unknown at address 0xc0758000
pcppi0 at isa0 port 0x61
midi2 at pcppi0: PC speaker
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff: using exception 16
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
isapnp0: no ISA Plug 'n Play devices found
apm0 at mainbus0: Power Management spec V1.2 (BIOS mgmt disabled)
APM power mgmt engage (device 1): power management disabled (0x10f)
biomask fbff netmask ffff ttymask ffff
cpu0: prelint0 8700<vector=0,delmode=7,level,dest=0> 0<target=0>
cpu0: prelint1 400<vector=0,delmode=4,dest=0> 0<target=0>
cpu0: timer0 300d0<vector=d0,delmode=0,masked,dest=0> 0<target=0>
cpu0: pcint0 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
cpu0: lint0 10700<vector=0,delmode=7,masked,dest=0> 0<target=0>
cpu0: lint1 400<vector=0,delmode=4,dest=0> 0<target=0>
cpu0: err0 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
ioapic0: enabling
ioapic0: int0 10700<vector=0,delmode=7,masked,dest=0> 0<target=0>
ioapic0: int1 1a0<vector=a0,delmode=1,dest=0> 0<target=0>
ioapic0: int2 10100<vector=0,delmode=1,masked,dest=0> 0<target=0>
ioapic0: int3 1e1<vector=e1,delmode=1,dest=0> 0<target=0>
ioapic0: int4 1e2<vector=e2,delmode=1,dest=0> 0<target=0>
ioapic0: int5 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
ioapic0: int6 170<vector=70,delmode=1,dest=0> 0<target=0>
ioapic0: int7 10100<vector=0,delmode=1,masked,dest=0> 0<target=0>
ioapic0: int8 10100<vector=0,delmode=1,masked,dest=0> 0<target=0>
ioapic0: int9 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
ioapic0: int10 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
ioapic0: int11 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
ioapic0: int12 1a1<vector=a1,delmode=1,dest=0> 0<target=0>
ioapic0: int13 10100<vector=0,delmode=1,masked,dest=0> 0<target=0>
ioapic0: int14 171<vector=71,delmode=1,dest=0> 0<target=0>
ioapic0: int15 172<vector=72,delmode=1,dest=0> 0<target=0>
ioapic0: int16 a173<vector=73,delmode=1,actlo,level,dest=0> 0<target=0>
ioapic0: int17 a1c0<vector=c0,delmode=1,actlo,level,dest=0> 0<target=0>
ioapic0: int18 1a100<vector=0,delmode=1,actlo,level,masked,dest=0> 0<target=0>
ioapic0: int19 a174<vector=74,delmode=1,actlo,level,dest=0> 0<target=0>
ioapic0: int20 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
ioapic0: int21 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
ioapic0: int22 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
ioapic0: int23 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
findroot: can't open dev wd1a (6)
boot device: wd0
root on wd0a dumps on wd0b
mountroot: trying coda...
mountroot: trying msdos...
mountroot: trying cd9660...
mountroot: trying ntfs...
mountroot: trying nfs...
mountroot: trying lfs...
mountroot: trying ext2fs...
mountroot: trying ffs...
root file system type: ffs
init: copying out path `/sbin/init' 11
ex0: device timeout
ex0: device timeout
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
ex0: device timeout
ex0: device timeout
ex0: device timeout
ex0: device timeout
ex0: device timeout
ex0: device timeout
ex0: device timeout

Regards,
	Murray Armfield