tech-install archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index][Old Index]
EFI Boot problem
Hello,
I am trying to boot installed NetBSD 10.1 on older HP machine HP Compaq
Elite 8300. System disk is GPT and contains Window Server OS and above
fresh NetBSD installation.
I am using rEFInd for dual-boot.
Problem is that after selecting NetBSD boot entry there does not appear
text-mode icon with:
...NetBSD/x86 EFI Boot (x64)...
There only appears some address ranges quickly scrolling up and then it
stops.
But
when I boot from USB key and use manual boot parameters to boot OS from
disk:
boot NAME=NetBSD:netbsd then OS on the disk successfully starts up.
I tried to rewrite bootx64.efi on EFI partition with /usr/mdec/bootx64.efi
or with bootx64.efi present on USB key, it does not help.
I don't know to explain myself this behavior.
Dmesg is in attachment. My NetBSD installation is on wd0 dk4.
Any ideas ?
[ 1.000000] Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003,
[ 1.000000] 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013,
[ 1.000000] 2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022, 2023,
[ 1.000000] 2024
[ 1.000000] The NetBSD Foundation, Inc. All rights reserved.
[ 1.000000] Copyright (c) 1982, 1986, 1989, 1991, 1993
[ 1.000000] The Regents of the University of California. All rights reserved.
[ 1.000000] NetBSD 10.1 (GENERIC) #0: Mon Dec 16 13:08:11 UTC 2024
[ 1.000000] mkrepro%mkrepro.NetBSD.org@localhost:/usr/src/sys/arch/amd64/compile/GENERIC
[ 1.000000] total memory = 24450 MB
[ 1.000000] avail memory = 23624 MB
[ 1.000000] timecounter: Timecounters tick every 10.000 msec
[ 1.000000] Kernelized RAIDframe activated
[ 1.000000] RTC BIOS diagnostic error 0x20<config_unit>
[ 1.000000] timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
[ 1.000004] efi: systbl at pa c943df18
[ 1.000004] mainbus0 (root)
[ 1.000004] ACPI: RSDP 0x00000000C9BA3000 000024 (v02 HPQOEM)
[ 1.000004] ACPI: XSDT 0x00000000C9BA3080 000084 (v01 HPQOEM SLIC-BPC 01072009 AMI 00010013)
[ 1.000004] ACPI: FACP 0x00000000C9BACFE8 0000F4 (v04 HPQOEM SLIC-BPC 01072009 AMI 00010013)
[ 1.000004] ACPI: DSDT 0x00000000C9BA3198 009E4A (v02 HPQOEM SLIC-BPC 00000017 INTL 20051117)
[ 1.000004] ACPI: FACS 0x00000000C9BB5F80 000040
[ 1.000004] ACPI: APIC 0x00000000C9BAD0E0 0000BC (v03 HPQOEM SLIC-BPC 01072009 AMI 00010013)
[ 1.000004] ACPI: MCFG 0x00000000C9BAD1A0 00003C (v01 HPQOEM SLIC-BPC 01072009 MSFT 00000097)
[ 1.000004] ACPI: HPET 0x00000000C9BAD1E0 000038 (v01 HPQOEM SLIC-BPC 01072009 AMI. 00000005)
[ 1.000004] ACPI: SSDT 0x00000000C9BAD218 000460 (v01 IdeRef IdeTable 00001000 INTL 20091112)
[ 1.000004] ACPI: SSDT 0x00000000C9BAD678 00544C (v01 COMPAQ WMI 00000001 MSFT 03000001)
[ 1.000004] ACPI: SLIC 0x00000000C9BB2AC8 000176 (v01 HPQOEM SLIC-BPC 00000001 00000000)
[ 1.000004] ACPI: SSDT 0x00000000C9BB2C40 0009AA (v01 PmRef Cpu0Ist 00003000 INTL 20051117)
[ 1.000004] ACPI: SSDT 0x00000000C9BB35F0 000A92 (v01 PmRef CpuPm 00003000 INTL 20051117)
[ 1.000004] ACPI: DMAR 0x00000000C9BB4088 0000B8 (v01 INTEL SNB 00000001 INTL 00000001)
[ 1.000004] ACPI: ASF! 0x00000000C9BB4140 0000A5 (v32 INTEL HCG 00000001 TFSM 000F4240)
[ 1.000004] ACPI: BGRT 0x00000000C9BB41E8 00003C (v00 HPQOEM SLIC-BPC 01072009 AMI 00010013)
[ 1.000004] ACPI: 5 ACPI AML tables successfully acquired and loaded
[ 1.000004] ioapic0 at mainbus0 apid 2: pa 0xfec00000, version 0x20, 24 pins
[ 1.000004] cpu0 at mainbus0 apid 0
[ 1.000004] cpu0: Use lfence to serialize rdtsc
[ 1.000004] cpu0: Intel(R) Core(TM) i7-3770 CPU @ 3.40GHz, id 0x306a9
[ 1.000004] cpu0: node 0, package 0, core 0, smt 0
[ 1.000004] cpu1 at mainbus0 apid 2
[ 1.000004] cpu1: Intel(R) Core(TM) i7-3770 CPU @ 3.40GHz, id 0x306a9
[ 1.000004] cpu1: node 0, package 0, core 1, smt 0
[ 1.000004] cpu2 at mainbus0 apid 4
[ 1.000004] cpu2: Intel(R) Core(TM) i7-3770 CPU @ 3.40GHz, id 0x306a9
[ 1.000004] cpu2: node 0, package 0, core 2, smt 0
[ 1.000004] cpu3 at mainbus0 apid 6
[ 1.000004] cpu3: Intel(R) Core(TM) i7-3770 CPU @ 3.40GHz, id 0x306a9
[ 1.000004] cpu3: node 0, package 0, core 3, smt 0
[ 1.000004] cpu4 at mainbus0 apid 1
[ 1.000004] cpu4: Intel(R) Core(TM) i7-3770 CPU @ 3.40GHz, id 0x306a9
[ 1.000004] cpu4: node 0, package 0, core 0, smt 1
[ 1.000004] cpu5 at mainbus0 apid 3
[ 1.000004] cpu5: Intel(R) Core(TM) i7-3770 CPU @ 3.40GHz, id 0x306a9
[ 1.000004] cpu5: node 0, package 0, core 1, smt 1
[ 1.000004] cpu6 at mainbus0 apid 5
[ 1.000004] cpu6: Intel(R) Core(TM) i7-3770 CPU @ 3.40GHz, id 0x306a9
[ 1.000004] cpu6: node 0, package 0, core 2, smt 1
[ 1.000004] cpu7 at mainbus0 apid 7
[ 1.000004] cpu7: Intel(R) Core(TM) i7-3770 CPU @ 3.40GHz, id 0x306a9
[ 1.000004] cpu7: node 0, package 0, core 3, smt 1
[ 1.000004] acpi0 at mainbus0: Intel ACPICA 20221020
[ 1.000004] acpi0: X/RSDT: OemId <HPQOEM,SLIC-BPC,01072009>, AslId <AMI ,00010013>
[ 1.000004] acpi0: MCFG: segment 0, bus 0-63, address 0x00000000f8000000
[ 1.000004] ACPI: Dynamic OEM Table Load:
[ 1.000004] ACPI: SSDT 0xFFFFE6B95FCBA008 00083B (v01 PmRef Cpu0Cst 00003001 INTL 20051117)
[ 1.000004] ACPI: Dynamic OEM Table Load:
[ 1.000004] ACPI: SSDT 0xFFFFE6BE573F6408 000303 (v01 PmRef ApIst 00003000 INTL 20051117)
[ 1.000004] ACPI: Dynamic OEM Table Load:
[ 1.000004] ACPI: SSDT 0xFFFFE6B95FC50408 000119 (v01 PmRef ApCst 00003000 INTL 20051117)
[ 1.000004] acpi0: SCI interrupting at int 9
[ 1.000004] acpi0: fixed power button present
[ 1.000004] timecounter: Timecounter "ACPI-Safe" frequency 3579545 Hz quality 900
[ 1.010635] hpet0 at acpi0: high precision event timer (mem 0xfed00000-0xfed00400)
[ 1.010635] timecounter: Timecounter "hpet0" frequency 14318180 Hz quality 2000
[ 1.011366] acpiec0 at acpi0 (H_EC, PNP0C09-1): not present
[ 1.011366] TPMX (PNP0C01) at acpi0 not configured
[ 1.011366] FWHD (INT0800) at acpi0 not configured
[ 1.011366] attimer1 at acpi0 (TIMR, PNP0100): io 0x40-0x43,0x50-0x53 irq 0
[ 1.011366] pckbc1 at acpi0 (PS2K, PNP0303) (kbd port): io 0x60,0x64 irq 1
[ 1.011366] pckbc2 at acpi0 (PS2M, PNP0F03) (aux port): irq 12
[ 1.011366] com0 at acpi0 (UAR1, PNP0501-1): io 0x3f8-0x3ff irq 4
[ 1.011366] com0: ns16550a, 16-byte FIFO
[ 1.011366] acpivga0 at acpi0 (VGA): ACPI Display Adapter
[ 1.011366] acpiout0 at acpivga0 (LCD, 0x0110): ACPI Display Output Device
[ 1.011366] acpiout0: brightness levels: [0-19]
[ 1.011366] acpivga0: connected output devices:
[ 1.011366] acpivga0: 0x0110 (acpiout0): LCD Panel, head 0
[ 1.011366] acpivga1 at acpi0 (GFX0): ACPI Display Adapter
[ 1.011366] acpiout1 at acpivga1 (DD01, 0x0100): ACPI Display Output Device
[ 1.011366] acpiout2 at acpivga1 (DD02, 0x0400): ACPI Display Output Device
[ 1.011366] acpiout2: brightness levels: [0,5,10,15,20,25,30,35,40,45,50,55,60,65,70,75,80,85,90,95,100]
[ 1.011366] acpiout3 at acpivga1 (DD03, 0x0300): ACPI Display Output Device
[ 1.011366] acpiout4 at acpivga1 (DD04, 0x0301): ACPI Display Output Device
[ 1.011366] acpiout5 at acpivga1 (DD05, 0x0302): ACPI Display Output Device
[ 1.011366] acpiout6 at acpivga1 (DD06, 0x0303): ACPI Display Output Device
[ 1.011366] acpiout7 at acpivga1 (DD07, 0x0304): ACPI Display Output Device
[ 1.011366] acpiout8 at acpivga1 (DD08, 0x0305): ACPI Display Output Device
[ 1.011366] acpiout9 at acpivga1 (LCD, 0x0110): ACPI Display Output Device
[ 1.011366] acpiout9: brightness levels: [0-19]
[ 1.011366] acpivga1: connected output devices:
[ 1.011366] acpivga1: 0x0110 (acpiout9): LCD Panel, head 0
[ 1.011366] acpibut0 at acpi0 (PWRB, PNP0C0C-170): ACPI Power Button
[ 1.011366] MEM2 (PNP0C01) at acpi0 not configured
[ 1.011366] acpiwmi0 at acpi0 (WMID, PNP0C14-0): ACPI WMI Interface
[ 1.011366] wmihp0 at acpiwmi0: HP WMI mappings
[ 1.011366] acpifan0 at acpi0 (FAN0, PNP0C0B-0): ACPI Fan
[ 1.011366] acpifan1 at acpi0 (FAN1, PNP0C0B-1): ACPI Fan
[ 1.011366] acpifan2 at acpi0 (FAN2, PNP0C0B-2): ACPI Fan
[ 1.011366] acpifan3 at acpi0 (FAN3, PNP0C0B-3): ACPI Fan
[ 1.011366] acpifan4 at acpi0 (FAN4, PNP0C0B-4): ACPI Fan
[ 1.011366] acpitz0 at acpi0 (TZ00)
[ 1.011366] acpitz0: active cooling level 0: 71.0C
[ 1.011366] acpitz0: active cooling level 1: 55.0C
[ 1.011366] acpitz0: active cooling level 2: 0.0C
[ 1.011366] acpitz0: active cooling level 3: 0.0C
[ 1.011366] acpitz0: active cooling level 4: 0.0C
[ 1.011366] acpitz0: levels: critical 105.0 C
[ 1.011366] acpitz1 at acpi0 (TZ01): cpu0 cpu4 cpu1 cpu5 cpu2 cpu6 cpu3 cpu7
[ 1.011366] acpitz1: levels: critical 105.0 C, passive 95.0 C, passive cooling
[ 1.011366] ACPI: Enabled 4 GPEs in block 00 to 3F
[ 1.011366] pckbd0 at pckbc1 (kbd slot)
[ 1.011366] pckbc1: using irq 1 for kbd slot
[ 1.011366] wskbd0 at pckbd0: console keyboard
[ 1.011366] pms0 at pckbc1 (aux slot)
[ 1.011366] pms0: autoconfiguration error: Failed to get E6 signature.
[ 1.011366] pms0: autoconfiguration error: Failed to initialize an ALPS device.
[ 1.011366] pckbc1: using irq 12 for aux slot
[ 1.011366] wsmouse0 at pms0 mux 0
[ 1.011366] pci0 at mainbus0 bus 0: configuration mode 1
[ 1.011366] pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
[ 1.011366] pchb0 at pci0 dev 0 function 0: Intel Ivy Bridge Host Bridge (rev. 0x09)
[ 1.011366] ppb0 at pci0 dev 1 function 0: Intel Ivy Bridge PCI Express Root Port (rev. 0x09)
[ 1.011366] ppb0: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x16 @ 8.0GT/s
[ 1.011366] pci1 at ppb0 bus 1
[ 1.011366] pci1: i/o space, memory space enabled, rd/line, wr/inv ok
[ 1.011366] nouveau0 at pci1 dev 0 function 0: NVIDIA product 107d (rev. 0xa1)
[ 1.011366] hdaudio0 at pci1 dev 0 function 1: HD Audio Controller
[ 1.011366] hdaudio0: interrupting at msi0 vec 0
[ 1.011366] hdaudio0: HDA ver. 1.0, OSS 2, ISS 4, BSS 0, SDO 4, 64-bit
[ 1.011366] hdafg0 at hdaudio0: NVIDIA product 001c
[ 1.011366] hdafg0: DP00 8ch: Digital Out [Jack]
[ 1.011366] hdafg0: DP01 8ch: Digital Out [Jack]
[ 1.011366] hdafg0: 8ch/0ch 48000Hz PCM16*
[ 1.011366] audio0 at hdafg0: playback, capture, full duplex, independent
[ 1.011366] audio0: slinear_le:16 2ch 48000Hz, blk 1920 bytes (10ms) for playback
[ 1.011366] audio0: slinear_le:16 2ch 48000Hz, blk 1920 bytes (10ms) for recording
[ 1.011366] spkr0 at audio0: PC Speaker (synthesized)
[ 1.011366] wsbell at spkr0 not configured
[ 1.011366] i915drmkms0 at pci0 dev 2 function 0: Intel Ivy Bridge Integrated Graphics Device (rev. 0x09)
[ 1.011366] xhci0 at pci0 dev 20 function 0: Intel 7 Series USB xHCI (rev. 0x04)
[ 1.011366] xhci0: 64-bit DMA
[ 1.011366] xhci0: interrupting at msi1 vec 0
[ 1.011366] xhci0: xHCI version 1.0
[ 1.011366] usb0 at xhci0: USB revision 3.0
[ 1.011366] usb1 at xhci0: USB revision 2.0
[ 1.011366] Intel 7 Series MEI Controller (miscellaneous communications, revision 0x04) at pci0 dev 22 function 0 not configured
[ 1.011366] puc0 at pci0 dev 22 function 3: Intel 7 Series KT (com)
[ 1.011366] com2 at puc0 port 0 (16550-compatible): ioaddr 0xf140, interrupting at ioapic0 pin 19
[ 1.011366] com2: ns16550a, 16-byte FIFO
[ 1.011366] wm0 at pci0 dev 25 function 0, 64-bit DMA: PCH2 LAN (82579LM) Controller (rev. 0x04)
[ 1.011366] wm0: interrupting at msi2 vec 0
[ 1.011366] wm0: PCI-Express bus
[ 1.011366] wm0: 2048 words FLASH, version 0.13.4
[ 1.011366] wm0: RX packet buffer size: 26KB
[ 1.011366] wm0: Ethernet address 10:60:4b:81:4e:f0
[ 1.011366] wm0: 0x6a4080<FLASH,PCIE,ASF_FIRM,AMT,WOL,EEE>
[ 1.011366] ihphy0 at wm0 phy 2: i82579 10/100/1000 media interface, rev. 3
[ 1.011366] ihphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
[ 1.011366] ehci0 at pci0 dev 26 function 0: Intel 7 Series USB EHCI (rev. 0x04)
[ 1.011366] ehci0: 64-bit DMA
[ 1.011366] ehci0: interrupting at ioapic0 pin 16
[ 1.011366] ehci0: BIOS has given up ownership
[ 1.011366] ehci0: EHCI version 1.0
[ 1.011366] ehci0: Using DMA subregion for control data structures
[ 1.011366] usb2 at ehci0: USB revision 2.0
[ 1.011366] hdaudio1 at pci0 dev 27 function 0: HD Audio Controller
[ 1.011366] hdaudio1: interrupting at msi3 vec 0
[ 1.011366] hdaudio1: HDA ver. 1.0, OSS 4, ISS 4, BSS 0, SDO 1, 64-bit
[ 1.011366] hdafg1 at hdaudio1: Realtek product 0221
[ 1.011366] hdafg1: DAC00 2ch: Speaker [Built-In]
[ 1.011366] hdafg1: DAC01 2ch: Speaker [Jack], HP Out [Jack]
[ 1.011366] hdafg1: ADC02 2ch: Line In [Jack], Mic In [Jack]
[ 1.011366] hdafg1: 2ch/2ch 44100Hz 48000Hz 96000Hz 192000Hz PCM16 PCM20 PCM24 AC3
[ 1.011366] audio1 at hdafg1: playback, capture, full duplex, independent
[ 1.011366] audio1: slinear_le:16 2ch 48000Hz, blk 1920 bytes (10ms) for playback
[ 1.011366] audio1: slinear_le:16 2ch 48000Hz, blk 1920 bytes (10ms) for recording
[ 1.011366] spkr1 at audio1: PC Speaker (synthesized)
[ 1.011366] wsbell at spkr1 not configured
[ 1.011366] hdafg2 at hdaudio1: Intel product 2806
[ 1.011366] hdafg2: DP00 8ch: Digital Out [Jack]
[ 1.011366] hdafg2: 8ch/0ch 48000Hz PCM16*
[ 1.011366] audio2 at hdafg2: playback, capture, full duplex, independent
[ 1.011366] audio2: slinear_le:16 2ch 48000Hz, blk 1920 bytes (10ms) for playback
[ 1.011366] audio2: slinear_le:16 2ch 48000Hz, blk 1920 bytes (10ms) for recording
[ 1.011366] spkr2 at audio2: PC Speaker (synthesized)
[ 1.011366] wsbell at spkr2 not configured
[ 1.011366] ppb1 at pci0 dev 28 function 0: Intel 7 Series PCIe (rev. 0xc4)
[ 1.011366] ppb1: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x4 @ 5.0GT/s
[ 1.011366] ppb1: link is x1 @ 2.5GT/s
[ 1.011366] pci2 at ppb1 bus 2
[ 1.011366] pci2: i/o space, memory space enabled, rd/line, wr/inv ok
[ 1.011366] ppb2 at pci2 dev 0 function 0: Texas Instruments product 8231 (rev. 0x03)
[ 1.011366] ppb2: PCI Express capability version 1 <PCI-E to PCI/PCI-X Bridge>
[ 1.011366] pci3 at ppb2 bus 3
[ 1.011366] pci3: i/o space, memory space enabled, rd/line, wr/inv ok
[ 1.011366] fwohci0 at pci3 dev 0 function 0: Texas Instruments product 8235 (rev. 0x01)
[ 1.011366] fwohci0: interrupting at ioapic0 pin 16
[ 1.011366] fwohci0: OHCI version 1.10 (ROM=1)
[ 1.011366] fwohci0: No. of Isochronous channels is 4.
[ 1.011366] fwohci0: EUI64 01:02:03:04:00:00:01:5a
[ 1.011366] fwohci0: Phy 1394a available S400, 2 ports.
[ 1.011366] fwohci0: Link S400, max_rec 2048 bytes.
[ 1.011366] ieee1394if0 at fwohci0: IEEE1394 bus
[ 1.011366] fwip0 at ieee1394if0: IP over IEEE1394
[ 1.011366] fwohci0: Initiate bus reset
[ 1.011366] fwohci0: Clear PME# now
[ 1.011366] ppb3 at pci0 dev 28 function 4: Intel 7 Series PCIe (rev. 0xc4)
[ 1.011366] ppb3: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x1 @ 5.0GT/s
[ 1.011366] ppb3: link is x1 @ 2.5GT/s
[ 1.011366] pci4 at ppb3 bus 4
[ 1.011366] pci4: i/o space, memory space enabled, rd/line, wr/inv ok
[ 1.011366] wm1 at pci4 dev 0 function 0, 64-bit DMA: Intel i82574L (rev. 0x00)
[ 1.011366] wm1: for TX and RX interrupting at msix4 vec 0 affinity to 1
[ 1.011366] wm1: for TX and RX interrupting at msix4 vec 1 affinity to 2
[ 1.011366] wm1: for LINK interrupting at msix4 vec 2
[ 1.011366] wm1: PCI-Express bus
[ 1.011366] wm1: 2048 words FLASH, version 1.8.0, Image Unique ID ffffffff
[ 1.011366] wm1: ASPM L0s and L1 are disabled to workaround the errata.
[ 1.011366] wm1: RX packet buffer size: 20KB
[ 1.011366] wm1: Ethernet address 68:05:ca:1a:df:15
[ 1.011366] wm1: 0x224080<FLASH,PCIE,ASF_FIRM,WOL>
[ 1.011366] makphy0 at wm1 phy 1: Marvell 88E1149 Gigabit PHY, rev. 1
[ 1.011366] makphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
[ 1.011366] ehci1 at pci0 dev 29 function 0: Intel 7 Series USB EHCI (rev. 0x04)
[ 1.011366] ehci1: 64-bit DMA
[ 1.011366] ehci1: interrupting at ioapic0 pin 23
[ 1.011366] ehci1: BIOS has given up ownership
[ 1.011366] ehci1: EHCI version 1.0
[ 1.011366] ehci1: Using DMA subregion for control data structures
[ 1.011366] usb3 at ehci1: USB revision 2.0
[ 1.011366] ppb4 at pci0 dev 30 function 0: Intel 82801BA Hub-PCI Bridge (rev. 0xa4)
[ 1.011366] pci5 at ppb4 bus 5
[ 1.011366] pci5: i/o space, memory space enabled
[ 1.011366] fxp0 at pci5 dev 0 function 0: i82558 Ethernet (rev. 0x04)
[ 1.011366] fxp0: interrupting at ioapic0 pin 20
[ 1.011366] fxp0: May need receiver lock-up workaround
[ 1.011366] fxp0: Ethernet address 00:a0:c9:9a:8c:21
[ 1.011366] inphy0 at fxp0 phy 1: i82555 10/100 media interface, rev. 0
[ 1.011366] inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
[ 1.011366] ichlpcib0 at pci0 dev 31 function 0: Intel Q77 LPC (rev. 0x04)
[ 1.011366] timecounter: Timecounter "ichlpcib0" frequency 3579545 Hz quality 1000
[ 1.011366] ichlpcib0: 24-bit timer
[ 1.011366] tco0 at ichlpcib0: TCO (watchdog) timer configured.
[ 1.011366] tco0: Min/Max interval 1/367 seconds
[ 1.011366] pciide0 at pci0 dev 31 function 2: Intel 7 Series (desktop) SATA Controller (rev. 0x04)
[ 1.011366] pciide0: bus-master DMA support present, but unused (no driver support)
[ 1.011366] pciide0: primary channel configured to native-PCI mode
[ 1.011366] pciide0: using ioapic0 pin 19 for native-PCI interrupt
[ 1.011366] atabus0 at pciide0 channel 0
[ 1.011366] pciide0: secondary channel configured to native-PCI mode
[ 1.011366] atabus1 at pciide0 channel 1
[ 1.011366] ichsmb0 at pci0 dev 31 function 3: Intel 7 Series SMBus Controller (rev. 0x04)
[ 1.011366] ichsmb0: interrupting at ioapic0 pin 18
[ 1.011366] iic0 at ichsmb0: I2C bus
[ 1.011366] pciide1 at pci0 dev 31 function 5: Intel 7 Series (desktop) SATA Controller (rev. 0x04)
[ 1.011366] pciide1: bus-master DMA support present, but unused (no driver support)
[ 1.011366] pciide1: primary channel wired to native-PCI mode
[ 1.011366] pciide1: using ioapic0 pin 19 for native-PCI interrupt
[ 1.011366] atabus2 at pciide1 channel 0
[ 1.011366] pciide1: secondary channel wired to native-PCI mode
[ 1.011366] atabus3 at pciide1 channel 1
[ 1.011366] isa0 at ichlpcib0
[ 1.011366] tpm0 at isa0 iomem 0xfed40000-0xfed40fff irq 7
[ 1.011366] tpm0: device 0x000b15d1 rev 0x10
[ 1.011366] pcppi0 at isa0 port 0x61
[ 1.011366] spkr3 at pcppi0: PC Speaker
[ 1.011366] wsbell at spkr3 not configured
[ 1.011366] midi0 at pcppi0: PC speaker
[ 1.011366] sysbeep0 at pcppi0
[ 1.011366] attimer1: attached to pcppi0
[ 1.011366] acpicpu0 at cpu0: ACPI CPU
[ 1.011366] acpicpu0: C1: FFH, lat 1 us, pow 1000 mW
[ 1.011366] acpicpu0: C2: FFH, lat 59 us, pow 500 mW
[ 1.011366] acpicpu0: C3: FFH, lat 80 us, pow 350 mW
[ 1.011366] acpicpu0: P0: FFH, lat 10 us, pow 77000 mW, 3401 MHz, turbo boost
[ 1.011366] acpicpu0: P1: FFH, lat 10 us, pow 77000 mW, 3400 MHz
[ 1.011366] acpicpu0: P2: FFH, lat 10 us, pow 73840 mW, 3300 MHz
[ 1.011366] acpicpu0: P3: FFH, lat 10 us, pow 67694 mW, 3100 MHz
[ 1.011366] acpicpu0: P4: FFH, lat 10 us, pow 64705 mW, 3000 MHz
[ 1.011366] acpicpu0: P5: FFH, lat 10 us, pow 61772 mW, 2900 MHz
[ 1.011366] acpicpu0: P6: FFH, lat 10 us, pow 58907 mW, 2800 MHz
[ 1.011366] acpicpu0: P7: FFH, lat 10 us, pow 53315 mW, 2600 MHz
[ 1.011366] acpicpu0: P8: FFH, lat 10 us, pow 50601 mW, 2500 MHz
[ 1.011366] acpicpu0: P9: FFH, lat 10 us, pow 47940 mW, 2400 MHz
[ 1.011366] acpicpu0: P10: FFH, lat 10 us, pow 42787 mW, 2200 MHz
[ 1.011366] acpicpu0: P11: FFH, lat 10 us, pow 40284 mW, 2100 MHz
[ 1.011366] acpicpu0: P12: FFH, lat 10 us, pow 37833 mW, 2000 MHz
[ 1.011366] acpicpu0: P13: FFH, lat 10 us, pow 35433 mW, 1900 MHz
[ 1.011366] acpicpu0: P14: FFH, lat 10 us, pow 31421 mW, 1700 MHz
[ 1.011366] acpicpu0: P15: FFH, lat 10 us, pow 29164 mW, 1600 MHz
[ 1.011366] coretemp0 at cpu0: thermal sensor, 1 C resolution, Tjmax=105
[ 1.011366] acpicpu1 at cpu1: ACPI CPU
[ 1.011366] coretemp1 at cpu1: thermal sensor, 1 C resolution, Tjmax=105
[ 1.011366] acpicpu2 at cpu2: ACPI CPU
[ 1.011366] coretemp2 at cpu2: thermal sensor, 1 C resolution, Tjmax=105
[ 1.011366] acpicpu3 at cpu3: ACPI CPU
[ 1.011366] coretemp3 at cpu3: thermal sensor, 1 C resolution, Tjmax=105
[ 1.011366] acpicpu4 at cpu4: ACPI CPU
[ 1.011366] acpicpu5 at cpu5: ACPI CPU
[ 1.011366] acpicpu6 at cpu6: ACPI CPU
[ 1.011366] acpicpu7 at cpu7: ACPI CPU
[ 1.011366] fwohci0: BUS reset
[ 1.011366] fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
[ 1.011366] ieee1394if0: 1 nodes, maxhop <= 0 cable IRM irm(0) (me)
[ 1.011366] ieee1394if0: bus manager 0
[ 1.011366] timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
[ 1.011366] timecounter: Timecounter "TSC" frequency 3392297000 Hz quality 3000
[ 1.226499] uhub0 at usb0: NetBSD (0x0000) xHCI root hub (0x0000), class 9/0, rev 3.00/1.00, addr 0
[ 1.238427] uhub0: 4 ports with 4 removable, self powered
[ 1.238427] uhub1 at usb1: NetBSD (0x0000) xHCI root hub (0x0000), class 9/0, rev 2.00/1.00, addr 0
[ 1.268426] uhub1: 4 ports with 4 removable, self powered
[ 1.288426] uhub2 at usb2: NetBSD (0x0000) EHCI root hub (0x0000), class 9/0, rev 2.00/1.00, addr 1
[ 1.308426] uhub2: 3 ports with 3 removable, self powered
[ 1.308426] uhub3 at usb3: NetBSD (0x0000) EHCI root hub (0x0000), class 9/0, rev 2.00/1.00, addr 1
[ 1.328426] uhub3: 3 ports with 3 removable, self powered
[ 1.328426] IPsec: Initialized Security Association Processing.
[ 1.358427] tpm0: read 8 bytes, expected 10
[ 1.378430] tpm0: deactivating entropy source
[ 1.398426] wd0 at atabus0 drive 1
[ 1.418426] wd0: <MTFDDAK128MAM-1J1>
[ 1.438426] wd0: drive supports 16-sector PIO transfers, LBA48 addressing
[ 1.438426] wd0: 119 GB, 248085 cyl, 16 head, 63 sec, 512 bytes/sect x 250069680 sectors
[ 1.468426] wd0: GPT GUID: 0b27f7c4-74b3-401c-88cd-c0d8c16ad0c3
[ 1.468426] dk0 at wd0: "Basic data partition", 1021952 blocks at 2048, type: <unknown>
[ 1.488425] dk1 at wd0: "EFI system partition", 204800 blocks at 1024000, type: msdos
[ 1.508425] dk2 at wd0: "Microsoft reserved partition", 32768 blocks at 1228800, type: ntfs
[ 1.528425] dk3 at wd0: "10bd2c78-377a-4082-8212-c1176362ec16", 80660480 blocks at 1261568, type: ntfs
[ 1.548425] autoconfiguration error: wd0: wedge named 'Basic data partition' already existed, using '10bd2c78-377a-4082-8212-c1176362ec16'
[ 1.568425] dk4 at wd0: "NetBSD", 163839936 blocks at 81922112, type: ffs
[ 1.588425] dk5 at wd0: "swap", 4307535 blocks at 245762112, type: swap
[ 1.618425] wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
[ 1.618425] wd1 at atabus1 drive 0
[ 1.638425] wd1: <WDC WD10EZEX-22BN5A0>
[ 1.658425] wd1: drive supports 16-sector PIO transfers, LBA48 addressing
[ 1.658425] wd1: 931 GB, 1938021 cyl, 16 head, 63 sec, 512 bytes/sect x 1953525168 sectors (4096 bytes/physsect)
[ 1.748425] wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
[ 1.748425] wd2 at atabus1 drive 1
[ 1.768424] wd2: <WDC WD5000AACS-00G8B0>
[ 1.788424] wd2: drive supports 16-sector PIO transfers, LBA48 addressing
[ 1.788424] wd2: 465 GB, 969021 cyl, 16 head, 63 sec, 512 bytes/sect x 976773168 sectors
[ 2.328423] wd2: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
[ 2.388433] uhub4 at uhub3 port 1: vendor 8087 (0x8087) product 0024 (0x0024), class 9/0, rev 2.00/0.00, addr 2
[ 2.408421] uhub4: single transaction translator
[ 2.428421] uhub5 at uhub2 port 1: vendor 8087 (0x8087) product 0024 (0x0024), class 9/0, rev 2.00/0.00, addr 2
[ 2.448421] uhub5: single transaction translator
[ 2.468421] uhub5: 6 ports with 6 removable, self powered
[ 2.468421] uhub4: 8 ports with 8 removable, self powered
[ 3.678417] umass0 at uhub5 port 1 configuration 1 interface 0
[ 3.698416] umass0: Corsair (0x1b1c) Voyager 3.0 (0x1a03), rev 2.10/1.10, addr 3
[ 3.718415] umass0: using SCSI over Bulk-Only
[ 3.728415] scsibus0 at umass0: 2 targets, 1 lun per target
[ 3.748415] sd0 at scsibus0 target 0 lun 0: <Corsair, Voyager 3.0, 000A> disk removable
[ 3.768415] sd0: fabricating a geometry
[ 3.788415] sd0: 29604 MB, 29604 cyl, 64 head, 32 sec, 512 bytes/sect x 60628992 sectors
[ 3.818417] sd0: fabricating a geometry
[ 4.188414] sd0: GPT GUID: 867794b8-d609-49ee-9c51-33a08260ec8b
[ 4.188414] dk6 at sd0: "EFI system", 262144 blocks at 2048, type: msdos
[ 4.208413] dk7 at sd0: "3c386667-4e85-4442-ac6e-943931e02174", 4853760 blocks at 264192, type: ffs
[ 4.228413] dk8 at sd0: "ab4a17e6-df64-4eda-9827-8e4b3e9f52b9", 20480000 blocks at 5117952, type: ntfs
[ 4.248413] autoconfiguration error: sd0: wedge named 'Basic data partition' already existed, using 'ab4a17e6-df64-4eda-9827-8e4b3e9f52b9'
[ 22.818332] atapibus0 at atabus2: 2 targets
[ 22.838331] cd0 at atapibus0 drive 0: <hp CDDVDW SH-216BB, R8TM6YBD604VA1, HE50> cdrom removable
[ 22.868333] cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
[ 22.868333] swwdog0: software watchdog initialized
[ 23.588330] WARNING: 4 errors while detecting hardware; check system log.
[ 23.588330] boot device: wd0
[ 23.588330] root on dk4 dumps on dk5
[ 23.608328] root file system type: ffs
[ 23.608328] kern.module.path=/stand/amd64/10.1/modules
[ 23.608328] nouveau0: NVIDIA GF119 (0d93d0a1)
[ 23.788327] nouveau0: bios: version 75.19.79.00.02
[ 23.938930] nouveau0: interrupting at msi5 vec 0 (nouveau0)
[ 23.938930] nouveau0: fb: 512 MiB DDR3
[ 24.248325] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 24.248325] [drm] Driver supports precise vblank timestamp query.
[ 24.248325] Zone kernel: Available graphics memory: 9007199252161660 KiB
[ 24.248325] Zone dma32: Available graphics memory: 2097152 KiB
[ 24.248325] nouveau0: DRM: VRAM: 512 MiB
[ 24.248325] nouveau0: DRM: GART: 1048576 MiB
[ 24.248325] nouveau0: DRM: TMDS table version 2.0
[ 24.248325] nouveau0: DRM: DCB version 4.0
[ 24.248325] nouveau0: DRM: DCB outp 00: 020003a6 0f220010
[ 24.248325] nouveau0: DRM: DCB outp 01: 02000362 00020010
[ 24.248325] nouveau0: DRM: DCB outp 02: 048113b6 0f220010
[ 24.248325] nouveau0: DRM: DCB outp 03: 04011372 00020010
[ 24.248325] nouveau0: DRM: DCB conn 00: 00410146
[ 24.248325] nouveau0: DRM: DCB conn 01: 00820246
[ 24.258325] nouveau0: DRM: MM: using COPY0 for buffer copies
[ 24.258325] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 24.258325] [drm] Driver supports precise vblank timestamp query.
[ 24.278324] nouveau0: [drm] Cannot find any crtc or sizes
[ 24.278324] [drm] Initialized nouveau 1.3.1 20120801 for nouveau0 on minor 0
[ 24.278324] i915drmkms0: interrupting at msi6 vec 0 (i915drmkms0)
[ 24.308324] [drm] Initialized i915 1.6.0 20200114 for i915drmkms0 on minor 1
[ 24.338324] intelfb0 at i915drmkms0
[ 24.338324] [drm] DRM_I915_DEBUG enabled
[ 24.338324] [drm] DRM_I915_DEBUG_GEM enabled
[ 24.338324] intelfb0: framebuffer at 0xd0005000, size 1280x1024, depth 32, stride 5120
[ 24.408324] {drm:netbsd:intel_set_cpu_fifo_underrun_reporting+0x29c} *ERROR* uncleared fifo underrun on pipe A
[ 24.408324] {drm:netbsd:intel_cpu_fifo_underrun_irq_handler+0x64} *ERROR* CPU pipe A FIFO underrun
[ 24.408324] {drm:netbsd:intel_set_pch_fifo_underrun_reporting+0x14e} *ERROR* uncleared pch fifo underrun on pch transcoder A
[ 24.408324] {drm:netbsd:cpt_irq_handler+0x217} *ERROR* PCH transcoder A FIFO underrun
[ 24.738322] wsdisplay0 at intelfb0 kbdmux 1: console (default, vt100 emulation), using wskbd0
[ 24.818322] wsmux1: connecting to wsdisplay0
[ 32.278289] wsdisplay0: screen 1 added (default, vt100 emulation)
[ 32.278289] wsdisplay0: screen 2 added (default, vt100 emulation)
[ 32.278289] wsdisplay0: screen 3 added (default, vt100 emulation)
[ 32.278289] wsdisplay0: screen 4 added (default, vt100 emulation)
Home |
Main Index |
Thread Index |
Old Index