CVS commit: [netbsd-6] src/sys/dev

["Martin Husemann" <martin%netbsd.org@localhost>]

Module Name:    src
Committed By:   martin
Date:           Sun Dec  7 16:39:55 UTC 2014

Modified Files:
        src/sys/dev/mii [netbsd-6]: brgphy.c brgphyreg.h
        src/sys/dev/pci [netbsd-6]: if_bge.c if_bgereg.h if_bnx.c if_bnxreg.h
            if_bnxvar.h

Log Message:
Pull up the following, requested by msaitoh in #1207:

sys/dev/mii/brgphy.c                            1.69, 1.71-1.76 via patch
sys/dev/mii/brgphyreg.h                         1.6-1.7, 1.9
sys/dev/pci/if_bge.c                            1.259,1.267-1.276 via patch
sys/dev/pci/if_bgereg.h                         1.87-1.88
sys/dev/pci/if_bnx.c                            1.48, 1.49, 1.52-1.57 via patch
sys/dev/pci/if_bnxreg.h                         1.15-1.18
sys/dev/pci/if_bnxvar.h                         1.4-1.6

        Changes for bge(4), bnx(4) and brgphy(4):
        - Add device IDs for Broadcom BCM57710, BCM57711(E), BCM57712(E) and
          BCM5719 into pcidevs.
        - Change BCM5720's device ID from 0x1658 to 0x165f. 0x1658 is only for
          the pre-product and not released to public.
        - Fix detection of BGEPHYF_FIBER_{MII|TBI}
        - Fix typo in comment.
        - KNF
        - brgphy(4):
          - Add BCM5708S support.
          - Add 2500SX support.
          - Fix bit definition of BRGPHY_MRBE_MSG_PG5_NP_T2 from FreeBSD.
          - Remove extra delay in brgphy_mii_phy_auto. Same as {Free,Open}BSD.
          - Fix media detect on some Fiber chips.
          - Add BCM5706.
        - bge(4):
          - Print yet another hardware config word in SRAM(BGE_SRAM_DATA_CFG_5)
            for BCM5717 and newer devices.
          - Fix a trivial bug in #ifdef NOTYET.
          - Add BGEPHYF_NO_WIRESPEED flag for fiber devices.
          - Print APE firmware correctly.
          - Don't use the PHY Auto Poll Mode on many chips. This fixes a bug
            that MII Fiber NIC drop packets about 50%. Same as {Free,Open}BSD.
            Tested on HP Moonshot.
          - Add workaround for PR#48451. Some BCM5717-5720 based systems get
            NMI on boot. This problem doesn't occur when we don't use
            prefetchable memory in the APE area. I don't know the reason...
            Tested with HP MicroServer Gen8.
          - Fix a bug that bge can't be initialized correctly on some sparc64
            systems (PR#49018).
          - Change initializaton order as the same as the document, Linux tg3
            and FreeBSD (part of r241436).
          - In the BCM5703, the DMA read watermark should be set to less than
            or equal to the maximum memory read byte count of the PCI-X command
            register. Same as FreeBSD r204978 and Linux tg3 driver.
        - bnx(4):
          - Enclose #ifdef BNX_DEBUG correctly.
          - Add 2500SX support.
          - Print some information (ASCI revision, PCI status, etc).
            From FreeBSD.


To generate a diff of this commit:
cvs rdiff -u -r1.59.8.6 -r1.59.8.7 src/sys/dev/mii/brgphy.c
cvs rdiff -u -r1.5.14.1 -r1.5.14.2 src/sys/dev/mii/brgphyreg.h
cvs rdiff -u -r1.200.2.3 -r1.200.2.4 src/sys/dev/pci/if_bge.c
cvs rdiff -u -r1.56.18.3 -r1.56.18.4 src/sys/dev/pci/if_bgereg.h
cvs rdiff -u -r1.45.8.1 -r1.45.8.2 src/sys/dev/pci/if_bnx.c
cvs rdiff -u -r1.14 -r1.14.10.1 src/sys/dev/pci/if_bnxreg.h
cvs rdiff -u -r1.2.8.1 -r1.2.8.2 src/sys/dev/pci/if_bnxvar.h

Please note that diffs are not public domain; they are subject to the
copyright notices on the relevant files.