Source-Changes-HG archive

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index][Old Index]

[src/trunk]: src/share/man/man4 New sentence, new line. Sort SEE ALSO.



details:   https://anonhg.NetBSD.org/src/rev/da2e5710e38e
branches:  trunk
changeset: 844210:da2e5710e38e
user:      wiz <wiz%NetBSD.org@localhost>
date:      Wed Aug 07 19:07:09 2019 +0000

description:
New sentence, new line. Sort SEE ALSO.

diffstat:

 share/man/man4/sb.4 |  30 +++++++++++++++++-------------
 1 files changed, 17 insertions(+), 13 deletions(-)

diffs (66 lines):

diff -r 98102d726a0b -r da2e5710e38e share/man/man4/sb.4
--- a/share/man/man4/sb.4       Wed Aug 07 16:14:51 2019 +0000
+++ b/share/man/man4/sb.4       Wed Aug 07 19:07:09 2019 +0000
@@ -1,4 +1,4 @@
-.\"    $NetBSD: sb.4,v 1.26 2019/08/05 15:06:47 ryoon Exp $
+.\"    $NetBSD: sb.4,v 1.27 2019/08/07 19:07:09 wiz Exp $
 .\"
 .\" Copyright (c) 1996 The NetBSD Foundation, Inc.
 .\" All rights reserved.
@@ -56,20 +56,24 @@
 The base I/O port address is usually jumper-selected to either 0x220 or
 0x240 (newer cards may provide software configuration, but this driver
 does not directly support them--you must configure the card for its I/O
-addresses with other software).  The SoundBlaster takes 16 I/O ports.
+addresses with other software).
+The SoundBlaster takes 16 I/O ports.
 For the SoundBlaster and SoundBlaster Pro, the IRQ and DRQ channels are
-jumper-selected.  For the SoundBlaster 16, the IRQ and DRQ channels are
-set by this driver to the values specified in the config file.  The IRQ
-must be selected from the set {5,7,9,10}.
+jumper-selected.
+For the SoundBlaster 16, the IRQ and DRQ channels are
+set by this driver to the values specified in the config file.
+The IRQ must be selected from the set {5,7,9,10}.
 .Pp
 The configuration file must use 1
 .Cm flags
-specification to enable the Jazz16 support.  This is to avoid potential
-conflicts with other devices when probing the Jazz 16 because it requires
-use of extra I/O ports not in the base port range.
+specification to enable the Jazz16 support.
+This is to avoid potential conflicts with other devices when probing
+the Jazz 16 because it requires use of extra I/O ports not in the
+base port range.
 .Pp
 With a SoundBlaster 16 card the device is full duplex, but it can
-only sensibly handle a precision of 8 bits.  It does so by extending
+only sensibly handle a precision of 8 bits.
+It does so by extending
 the output 8 bit samples to 16 bits and using the 8 bit DMA channel
 for input and the 16 bit channel for output.
 .Pp
@@ -86,13 +90,13 @@
 .Sh SEE ALSO
 .Xr aic 4 ,
 .Xr audio 4 ,
+.Xr i386/pnpbios 4 ,
 .Xr isa 4 ,
 .Xr isapnp 4 ,
 .Xr joy 4 ,
 .Xr midi 4 ,
 .Xr mpu 4 ,
-.Xr opl 4 ,
-.Xr i386/pnpbios 4
+.Xr opl 4
 .Sh HISTORY
 The
 .Nm
@@ -102,5 +106,5 @@
 Non-SCSI CD-ROM interfaces are not supported.
 .Pp
 The MIDI interface on the SB hardware is braindead, and the driver
-needs to busy wait while writing MIDI data.  This will consume
-a lot of system time.
+needs to busy wait while writing MIDI data.
+This will consume a lot of system time.



Home | Main Index | Thread Index | Old Index