[src/trunk]: src/usr.sbin/mrouted Whitespace nits.

[wiz <wiz%NetBSD.org@localhost>]

details:   https://anonhg.NetBSD.org/src/rev/6d3cec37b51d
branches:  trunk
changeset: 520912:6d3cec37b51d
user:      wiz <wiz%NetBSD.org@localhost>
date:      Sat Jan 19 03:39:46 2002 +0000

description:
Whitespace nits.

diffstat:

 usr.sbin/mrouted/mrouted.8 |  90 +++++++++++++++++++++++-----------------------
 1 files changed, 45 insertions(+), 45 deletions(-)

diffs (260 lines):

diff -r a66b7310f716 -r 6d3cec37b51d usr.sbin/mrouted/mrouted.8
--- a/usr.sbin/mrouted/mrouted.8        Sat Jan 19 03:38:36 2002 +0000
+++ b/usr.sbin/mrouted/mrouted.8        Sat Jan 19 03:39:46 2002 +0000
@@ -1,30 +1,30 @@
-'\"    $NetBSD: mrouted.8,v 1.9 1997/10/17 10:38:25 lukem Exp $
+'\"    $NetBSD: mrouted.8,v 1.10 2002/01/19 03:39:46 wiz Exp $
 '\"COPYRIGHT 1989 by The Board of Trustees of Leland Stanford Junior University.
 .TH MROUTED 8
 .UC 5
 .SH NAME
 mrouted \- IP multicast routing daemon
 .SH SYNOPSIS
-.B mrouted 
+.B mrouted
 [
 .B \-p
 ] [
-.B \-c 
+.B \-c
 .I config_file
 ] [
-.B \-d 
-[ 
+.B \-d
+[
 .I debug_level
 ]]
 .SH DESCRIPTION
-.I Mrouted 
+.I Mrouted
 is an implementation of the Distance-Vector Multicast Routing
 Protocol (DVMRP), an earlier version of which is specified in RFC-1075.
 It maintains topological knowledge via a distance-vector routing protocol
 (like RIP, described in RFC-1058), upon which it implements a multicast
 datagram forwarding algorithm called Reverse Path Multicasting.
 .PP
-.I Mrouted 
+.I Mrouted
 forwards a multicast datagram along a shortest (reverse) path tree
 rooted at the subnet on which the datagram originates. The multicast
 delivery tree may be thought of as a broadcast delivery tree that has
@@ -35,55 +35,55 @@
 used to limit the range of multicast datagrams.
 .PP
 In order to support multicasting among subnets that are separated by (unicast)
-routers that do not support IP multicasting, 
-.I mrouted 
+routers that do not support IP multicasting,
+.I mrouted
 includes support for
-"tunnels", which are virtual point-to-point links between pairs of 
+"tunnels", which are virtual point-to-point links between pairs of
 .IR mrouted s
 located anywhere in an internet.  IP multicast packets are encapsulated for
 transmission through tunnels, so that they look like normal unicast datagrams
-to intervening routers and subnets.  The encapsulation 
+to intervening routers and subnets.  The encapsulation
 is added on entry to a tunnel, and stripped off
 on exit from a tunnel.
 By default, the packets are encapsulated using the IP-in-IP protocol
 (IP protocol number 4).
-Older versions of 
+Older versions of
 .I mrouted
 tunnel using IP source routing, which puts a heavy load on some
 types of routers.
 This version does not support IP source route tunnelling.
 .PP
-The tunnelling mechanism allows 
-.I mrouted 
+The tunnelling mechanism allows
+.I mrouted
 to establish a virtual internet, for
 the purpose of multicasting only, which is independent of the physical
 internet, and which may span multiple Autonomous Systems.  This capability
 is intended for experimental support of internet multicasting only, pending
 widespread support for multicast routing by the regular (unicast) routers.
-.I Mrouted 
+.I Mrouted
 suffers from the well-known scaling problems of any distance-vector
 routing protocol, and does not (yet) support hierarchical multicast routing.
 .PP
-.I Mrouted 
+.I Mrouted
 handles multicast routing only; there may or may not be unicast routing
-software running on the same machine as 
+software running on the same machine as
 .IR mrouted .
 With the use of tunnels, it
-is not necessary for 
-.I mrouted 
+is not necessary for
+.I mrouted
 to have access to more than one physical subnet
 in order to perform multicast forwarding.
 .br
 .ne 5
 .SH INVOCATION
 .PP
-If no "\-d" option is given, or if the debug level is specified as 0, 
+If no "\-d" option is given, or if the debug level is specified as 0,
 .I mrouted
 detaches from the invoking terminal.  Otherwise, it remains attached to the
 invoking terminal and responsive to signals from that terminal.  If "\-d" is
 given with no argument, the debug level defaults to 2.  Regardless of the
-debug level, 
-.I mrouted 
+debug level,
+.I mrouted
 always writes warning and error messages to the system
 log demon.  Non-zero debug levels have the following effects:
 .IP "level 1"
@@ -98,7 +98,7 @@
 Upon startup, mrouted writes its pid to the file /var/run/mrouted.pid .
 .SH CONFIGURATION
 .PP
-.I Mrouted 
+.I Mrouted
 automatically configures itself to forward on all multicast-capable
 interfaces, i.e., interfaces that have the IFF_MULTICAST flag set (excluding
 the loopback "interface"), and it finds other
@@ -140,7 +140,7 @@
 The phyint command can be used to disable multicast routing on the physical
 interface identified by local IP address <local-addr>, or to associate a
 non-default metric or threshold with the specified physical interface.
-The local IP address <local-addr> may be replaced by the 
+The local IP address <local-addr> may be replaced by the
 interface name (e.g le0).
 If a phyint is attached to multiple IP subnets, describe each additional subnet
 with the altnet keyword.
@@ -157,7 +157,7 @@
 up in the mrouted.conf files of both routers before it can be used.
 '\"For backwards compatibility with older
 '\".IR mrouted s,
-'\"the srcrt keyword specifies 
+'\"the srcrt keyword specifies
 '\"encapsulation using IP source routing.
 .PP
 The cache_lifetime is a value that determines the amount of time that a
@@ -166,9 +166,9 @@
 .PP
 The pruning <off/on> option is provided for
 .IR mrouted
-to act as a non-pruning router. It is also possible to start 
+to act as a non-pruning router. It is also possible to start
 .IR mrouted
-in a non-pruning mode using the "-p" option on the command line. It is 
+in a non-pruning mode using the "-p" option on the command line. It is
 expected that a router would be configured in this manner for test
 purposes only. The default mode is pruning enabled.
 .PP
@@ -179,7 +179,7 @@
 The metric is the "cost" associated with sending a datagram on the given
 interface or tunnel; it may be used to influence the choice of routes.
 The metric defaults to 1.  Metrics should be kept as small as possible,
-because 
+because
 .I mrouted
 cannot route along paths with a sum of metrics greater
 than 31.
@@ -195,7 +195,7 @@
 connected to a particular subnet or tunnel should
 use the same metric and threshold for that subnet or tunnel.
 .PP
-The rate_limit option allows the network administrator to specify a 
+The rate_limit option allows the network administrator to specify a
 certain bandwidth in Kbits/second which would be allocated to multicast
 traffic.  It defaults to 500Kbps on tunnels, and 0 (unlimited) on physical
 interfaces.
@@ -210,7 +210,7 @@
 will not initiate execution if it has fewer than two enabled vifs,
 where a vif (virtual interface) is either a physical multicast-capable
 interface or a tunnel.  It will log a warning if all of its vifs are
-tunnels; such an 
+tunnels; such an
 .I mrouted
 configuration would be better replaced by more
 direct tunnels (i.e., eliminate the middle man).
@@ -255,7 +255,7 @@
 .fi
 .SH SIGNALS
 .PP
-.I Mrouted 
+.I Mrouted
 responds to the following signals:
 .IP HUP
 restarts
@@ -272,8 +272,8 @@
 dumps the internal cache tables to /var/tmp/mrouted.cache.
 .IP QUIT
 dumps the internal routing tables to stderr (only if
-.I mrouted 
-was invoked with a non-zero debug level). 
+.I mrouted
+was invoked with a non-zero debug level).
 .PP
 For convenience in sending signals,
 .I mrouted
@@ -293,13 +293,13 @@
                   pkts out: 2322323
 
   1   36.11.0.1     subnet: 36.11         1       1    querier
-                    groups: 224.0.2.1      
-                            224.0.1.0      
-                            224.0.0.4      
+                    groups: 224.0.2.1
+                            224.0.1.0
+                            224.0.0.4
                    pkts in: 345
                   pkts out: 3456
 
-  2   36.2.0.8      tunnel: 36.8.0.77     3       1   
+  2   36.2.0.8      tunnel: 36.8.0.77     3       1
                      peers: 36.8.0.77 (2.2)
                 boundaries: 239.0.1
                           : 239.1.2
@@ -321,7 +321,7 @@
 In this example, there are four vifs connecting to two subnets and two
 tunnels.  The vif 3 tunnel is not in use (no peer address). The vif 0 and
 vif 1 subnets have some groups present; tunnels never have any groups.  This
-instance of 
+instance of
 .I mrouted
 is the one responsible for sending periodic group
 membership queries on the vif 0 and vif 1 subnets, as indicated by the
@@ -339,9 +339,9 @@
 outgoing vif only if there are members of the destination group on that leaf.
 .bp
 .PP
-.I Mrouted 
+.I Mrouted
 also maintains a copy of the kernel forwarding cache table. Entries
-are created and deleted by 
+are created and deleted by
 .I mrouted.
 .PP
 The cache tables look like this:
@@ -349,17 +349,17 @@
 
 Multicast Routing Cache Table (147 entries)
  Origin             Mcast-group     CTmr  Age Ptmr IVif Forwvifs
- 13.2.116/22        224.2.127.255     3m   2m    -  0    1 
+ 13.2.116/22        224.2.127.255     3m   2m    -  0    1
 >13.2.116.19
 >13.2.116.196
- 138.96.48/21       224.2.127.255     5m   2m    -  0    1 
+ 138.96.48/21       224.2.127.255     5m   2m    -  0    1
 >138.96.48.108
- 128.9.160/20       224.2.127.255     3m   2m    -  0    1 
+ 128.9.160/20       224.2.127.255     3m   2m    -  0    1
 >128.9.160.45
- 198.106.194/24     224.2.135.190     9m  28s   9m  0P  
+ 198.106.194/24     224.2.135.190     9m  28s   9m  0P
 >198.106.194.22
 
-.fi 
+.fi
 Each entry is characterized by the origin subnet number and mask and the
 destination multicast group. The 'CTmr' field indicates the lifetime
 of the entry.  The entry is deleted from the cache table