Me again. Just in case it might help, I have included some extra
information above and below the boot sequence in the hope that it will
help with the diagnosis of the problem.

Thanks in advance.....


**********************************************************************


KA42-B  V1.3
ID 08-00-2B-14-9C-D7

   MONO     0000.0001
   CLK      0000.0001
   NVR      0000.0001
 ? DZ       0000.4001
      00000001 00000001 00000001 00004001 00000001 000012A0
   MEM      0010.0001
      01000000
   MM       0000.0001
   FP       0000.0001
   IT       0000.0001
   SCSI-A   2828.0001  V1.58
      FFFFFF05 FFFFFF05 FFFFFF05 00000001 FFFFFF05 00000001 FFFFFF05
FFFFFF03
   SCSI-B   0808.0001  V1.58
      FFFFFF05 FFFFFF05 FFFFFF05 00000001 FFFFFF05 FFFFFF05 FFFFFF05
FFFFFF03
   SYS      0000.0001
   8PLN     0000.0001  V1.3
   NI       0100.0001
>>> b


-ESA0
>> NetBSD/vax boot [980110 22:29] <<
: /netbsd
boot: client IP address: 150.103.44.17
boot: client name: dudsun2
root addr=150.103.44.15 path=/dka100/dudsun2/root
700416+38912+75784 start 0x9c078
Copyright (c) 1996, 1997 The NetBSD Foundation, Inc.  All rights
reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 1.3 (GENERIC) #1: Fri Jan 16 16:09:22 CET 1998
    ragge@multivac:/usr/hej/src/sys/arch/vax/compile/GENERIC

realmem = 16646144
avail mem = 12690432
Using 812 buffers containing 831488 bytes of memory.
backplane0 (root)
cpu0 at backplane0: MicroVAX 3100 (KA41)
vsbus0 at backplane0
le0 at vsbus0: address 08:00:2b:14:9c:d7
le0: 32 receive buffers, 8 transmit buffers
probing for SCSI controller at 0x200c0080...
result: 0x0 (0)
SCSI controller found.
probing for SCSI controller at 0x200c0080...
result: 0x0 (0)
SCSI controller found.
ncr0 at vsbus0: scsi-id 7
scsibus0 at ncr0: 8 targets
sd0 at scsibus0 targ 3 lun 0: <DEC, RZ23     (C) DEC, 0A18> SCSI1
0/direct fixed
sd0: 100MB, 776 cyl, 8 head, 33 sec, 512 bytes/sect x 204864 sectors
sd1 at scsibus0 targ 5 lun 0: <DEC, RX23     (C) DEC, 0054> SCSI1
0/direct remov
able
sd1: drive offline
probing for SCSI controller at 0x200c0180...
result: 0x0 (0)
SCSI controller found.
ncr1 at vsbus0: scsi-id 7
scsibus1 at ncr1: 8 targets
ncr1: no REQ for next phase, abort
ncr1: no REQ while aborting, reset
ncr1: reset SCSI bus for TID=3 LUN=0
ncr1: no REQ for next phase, abort
ncr1: no REQ while aborting, reset
ncr1: reset SCSI bus for TID=3 LUN=0

?02 EXT HLT
    PC = 8009C76B
>>>