Port-sparc64 archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index][Old Index]
major/minor numbers for puc? adapters on sparc64
Ok, I got a little silly, and installed a pair of puc(4) PCI
cards in a PCI sparc64 machine.
The kernel very merrily recognizes them and attaches them.
But, now, I'm at a loss on who to actaully access the critters.
All the device nodes in MAKEDEV are for the built in/Sun provide
serial adapters.
I went groveling through the kernel sources trying to figure out
what major number I should be using, but I didn't find/recognize
the information.
Can anyone provide the needed info?
Thanks!
fyi: I've attached the dmesg from the system with the puc(4)'s
in it.. yes, it's a rather old -current kernel, but it's been
running and doing its job, so I haven't touched it in a while.
--
Eric Schnoebelen eric%cirr.com@localhost
http://www.cirr.com
Okay, who put a "stop payment" on my reality check?
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 4.99.34 (GENERIC) #17: Sat Oct 27 02:48:22 CDT 2007
eric%egsner.cirr.com@localhost:/work/eric/NetBSD-current/obj/sparc64/sys/arch/sparc64/compile/GENERIC
total memory = 1024 MB
avail memory = 991 MB
timecounter: Timecounters tick every 10.000 msec
mainbus0 (root): SUNW,UltraSPARC-IIi-Engine: hostid 80d1acf0
cpu0 at mainbus0: SUNW,UltraSPARC-IIi @ 360.093 MHz, UPA id 0
cpu0: 32K instruction (32 b/l), 16K data (32 b/l), 256K external (64 b/l)
psycho0 at mainbus0 addr 0xfffc0000
SUNW,sabre: impl 0, version 0: ign 7c0 bus range 0 to 129; PCI bus 0
DVMA map: c0000000 to e0000000
IOTSB: 10c2000 to 1142000
pci0 at psycho0
pci0: i/o space, memory space enabled
ppb0 at pci0 dev 1 function 1: Sun Microsystems Simba PCI bridge (rev. 0x13)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
ebus0 at pci1 dev 1 function 0
ebus0: Sun Microsystems PCIO Ebus2, revision 0x01
auxio0 at ebus0 addr 726000-726003, 728000-728003, 72a000-72a003,
72c000-72c003, 72f000-72f003
power at ebus0 addr 724000-724003 ipl 37 not configured
SUNW,pll at ebus0 addr 504000-504002 not configured
sab0 at ebus0 addr 400000-40007f ipl 43: rev 3.2
sabtty0 at sab0 port 0: console i/o
sabtty1 at sab0 port 1
com0 at ebus0 addr 3803f8-3803ff ipl 41: ns16550a, working fifo
kbd0 at com0
com1 at ebus0 addr 3602f8-3602ff ipl 42: ns16550a, working fifo
ms0 at com1
wsmouse0 at ms0 mux 0
lpt0 at ebus0 addr 340278-340287, 30015c-30015d, 700000-70000f ipl 34
fdthree at ebus0 addr 3203f0-3203f7, 706000-70600f, 720000-720003 ipl 39 not
configured
clock0 at ebus0 addr 0-1fff: mk48t59
flashprom at ebus0 addr 0-fffff not configured
beeper at ebus0 addr 722000-722003 not configured
hme0 at pci1 dev 1 function 1: Sun Happy Meal Ethernet, rev. 1
hme0: interrupting at ivec 3021
hme0: Ethernet address 08:00:20:d1:ac:f0
nsphy0 at hme0 phy 1: DP83840 10/100 media interface, rev. 1
nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ppb1 at pci0 dev 1 function 0: Sun Microsystems Simba PCI bridge (rev. 0x13)
pci2 at ppb1 bus 128
pci2: i/o space, memory space enabled
esiop0 at pci2 dev 1 function 0: Symbios Logic 53c875 (ultra-wide scsi)
esiop0: using on-board RAM
esiop0: interrupting at ivec 1820
scsibus0 at esiop0: 16 targets, 8 luns per target
esiop1 at pci2 dev 1 function 1: Symbios Logic 53c875 (ultra-wide scsi)
esiop1: using on-board RAM
esiop1: interrupting at ivec 1820
scsibus1 at esiop1: 16 targets, 8 luns per target
ppb2 at pci2 dev 4 function 0: Digital Equipment DC21154 PCI-PCI Bridge (rev.
0x02)
pci3 at ppb2 bus 129
pci3: i/o space, memory space enabled
puc0 at pci3 dev 4 function 0: NetMos NM9835 Dual UART (com, com)
com2 at puc0 port 0: interrupting at ivec 10
com2: ns16550a, working fifo
com3 at puc0 port 1: interrupting at ivec 10
com3: ns16550a, working fifo
puc1 at pci3 dev 5 function 0: NetMos NM9835 Dual UART (com, com)
com4 at puc1 port 0: interrupting at ivec 11
com4: ns16550a, working fifo
com5 at puc1 port 1: interrupting at ivec 11
com5: ns16550a, working fifo
pcons at mainbus0 not configured
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "tick-counter" frequency 360093046 Hz quality 100
No counter-timer -- using %tick at 360MHz as system clock.
wskbd0 at kbd0 mux 1
scsibus0: waiting 2 seconds for devices to settle...
scsibus1: waiting 2 seconds for devices to settle...
sd0 at scsibus0 target 0 lun 0: <FUJITSU, MAS3735NC, 0104> disk fixed
sd0: 70093 MB, 27094 cyl, 8 head, 662 sec, 512 bytes/sect x 143552136 sectors
sd0: sync (50.00ns offset 16), 16-bit (40.000MB/s) transfers, tagged queueing
sd1 at scsibus0 target 1 lun 0: <FUJITSU, MAS3735NC, 0104> disk fixed
sd1: 70093 MB, 27094 cyl, 8 head, 662 sec, 512 bytes/sect x 143552136 sectors
sd1: sync (50.00ns offset 16), 16-bit (40.000MB/s) transfers, tagged queueing
sd2 at scsibus0 target 2 lun 0: <FUJITSU, MAS3735NC, 0104> disk fixed
sd2: 70093 MB, 27094 cyl, 8 head, 662 sec, 512 bytes/sect x 143552136 sectors
sd2: sync (50.00ns offset 16), 16-bit (40.000MB/s) transfers, tagged queueing
sd3 at scsibus0 target 3 lun 0: <FUJITSU, MAS3735NC, 0104> disk fixed
sd3: 70093 MB, 27094 cyl, 8 head, 662 sec, 512 bytes/sect x 143552136 sectors
sd3: sync (50.00ns offset 16), 16-bit (40.000MB/s) transfers, tagged queueing
cd0 at scsibus0 target 6 lun 0: <TOSHIBA, CD-ROM XM-3701TA, 2965> cdrom
removable
cd0: async, 8-bit transfers
kbd0: reset failed
Kernelized RAIDframe activated
raid0: RAID Level 1
raid0: Components: /dev/sd0a /dev/sd1a
raid0: Total Sectors: 25163968 (12287 MB)
raid1: RAID Level 5
raid1: Components: /dev/sd0h /dev/sd1h /dev/sd2h
raid1: Total Sectors: 236776000 (115613 MB)
root on raid0a dumps on raid0b
root file system type: ffs
Home |
Main Index |
Thread Index |
Old Index