right, so I gave it a try and... it fails ;(
in fact, it loops "into the kernel" (check end of mail).

if anyone has a clue of what's happening and how to solve this...
for infos, I did boot the machine with linux/debian and it didn't loop
(so I guess it's not a hardware problem)

thanks for answers,
	Jo

On Fri, Mar 28 2003 - 13:04, Emre Yildirim wrote:
> > On Thu, Mar 27, 2003 at 10:57:37PM +0100, ptiJo wrote:
> >> Hi,
> >>
> >> I have an Ultra5 running OpenBSD/sparc64 :
> >> ****************************************************
> >> mainbus0 (root): SUNW,Ultra-5_10
> >> cpu0 at mainbus0: SUNW,UltraSPARC-IIi @ 333 MHz, version 0 FPU
> >> cpu0: physical 32K instruction (32 b/l), 16K data (32 b/l), 2048K
> >> external (64 b/l) <SNIP>
> >> scsibus1 at isp0: 16 targets
> >> "Adaptec AHA-29160 U160" rev 0x02 at pci2 dev 3 function 0 not
> >> configured ****************************************************
> >>
> >> is the AHA-29160 better supported on NetBSD/sparc64 ?
> 
> Most of NetBSD device drivers are machine-independent.  That means if your
> Ultra5 uses a PCI bus (which I'm sure it does) any PCI card that is
> supported by NetBSD should work.  That particular card is not listed under
> the supported hardware list, but the AHA-294x is...so I'm sure it will
> work.  You can give it a try and see what happens.
> 
> take care
> 

**** BOOT PROCESS ***

NetBSD 1.6.1 (INSTALL) #0: Mon Apr  7 10:47:36 UTC 2003
    autobuild@cs20.apochromatic.org:/autobuilder/build/netbsd-1-6/sparc64/OBJ/autobuilderL
total memory = 256 MB                                                                    
avail memory = 224 MB
using 1651 buffers containing 13208 KB of memory
bootpath: /pci@1f,0/pci@1,1/network@1,1         
mainbus0 (root): SUNW,Ultra-5_10       
cpu0 at mainbus0: SUNW,UltraSPARC-IIi @ 333 MHz, version 0 FPU
cpu0: physical 32K instruction (32 b/l), 16K data (32 b/l), 2048K external (64 b/l)
psycho0 at mainbus0 addr 0xfffc4000                                                
SUNW,sabre: impl 0, version 0: ign 7c0 bus range 0 to 2; PCI bus 0
intr_establish: intr reused 7c0                                   
DVMA map: c0000000 to e0000000 
IOTSB: 112ac000 to 1132c000   
pci0 at psycho0            
pci0: i/o space, memory space enabled
ppb0 at pci0 dev 1 function 1: Sun Microsystems Simba PCI bridge (rev. 0x13)
pci1 at ppb0 bus 1                                                          
pci1: i/o space, memory space enabled
ebus0 at pci1 dev 1 function 0       
ebus0: Sun Microsystems PCIO Ebus2, revision 0x01
auxio0 at ebus0 addr 726000-726003, 728000-728003, 72a000-72a003, 72c000-72c003, 72f000-73
power at ebus0 addr 724000-724003 ipl 37 not configured                                  
SUNW,pll at ebus0 addr 504000-504002 not configured    
se at ebus0 addr 400000-40007f ipl 43 not configured
com0 at ebus0 addr 3083f8-3083ff ipl 41: ns16550a, working fifo
kbd0 at com0                                                   
com1 at ebus0 addr 3062f8-3062ff ipl 42: ns16550a, working fifo
ms0 at com1                                                    
lpt0 at ebus0 addr 3043bc-3043cb, 30015c-30015d, 700000-70000f ipl 34
fdthree at ebus0 addr 3023f0-3023f7, 706000-70600f, 720000-720003 ipl 39 not configured
clock0 at ebus0 addr 0-1fff: mk48t59: hostid 80a7e931                                  
flashprom at ebus0 addr 0-fffff not configured       
audiocs0 at ebus0 addr 200000-2000ff, 702000-70200f, 704000-70400f, 722000-722003 ipl 35 A
audio0 at audiocs0: full duplex                                                          
hme0 at pci1 dev 1 function 1: Sun Happy Meal Ethernet, rev. 1
hme0: interrupting at ivec 3021                               
hme0: Ethernet address 08:00:20:a7:e9:31
nsphy0 at hme0 phy 1: DP83840 10/100 media interface, rev. 1
nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ATI Technologies 3D Rage Pro (VGA display, revision 0x5c) at pci1 dev 2 function 0 not cod
pciide0 at pci1 dev 3 function 0: CMD Technology PCI0646 (rev. 0x03)                     
pciide0: bus-master DMA support present                             
pciide0: primary channel configured to native-PCI mode
pciide0: using ivec 1820 for native-PCI interrupt     
wd0 at pciide0 channel 0 drive 0: <QUANTUM FIREBALLP LM30>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 28629 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 58633344 sectors
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 4 (Ultra/66)     
wd1 at pciide0 channel 0 drive 1: <IC35L040AVER07-0>                   
wd1: drive supports 16-sector PIO transfers, LBA addressing
wd1: 39266 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 80418240 sectors
wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)    
wd0(pciide0:0:0): using PIO mode 4, DMA mode 2 (using DMA data transfers)
wd1(pciide0:0:1): using PIO mode 4, DMA mode 2 (using DMA data transfers)
pciide0: secondary channel configured to native-PCI mode                 
atapibus0 at pciide0 channel 1: 2 targets               
cd0 at atapibus0 drive 0: <CRD-8322B, 1998/09/24, 1.05> type 5 cdrom removable
cd0: drive supports PIO mode 4, DMA mode 2                                    
cd0(pciide0:1:0): using PIO mode 4, DMA mode 2 (using DMA data transfers)
ppb1 at pci0 dev 1 function 0: Sun Microsystems Simba PCI bridge (rev. 0x13)
pci2 at ppb1 bus 2                                                          
pci2: i/o space, memory space enabled
ahc0 at pci2 dev 3 function 0        
ahc0: OptionMode = 3         
ahc0: interrupting at ivec 18
ahc0: aic7892 Wide Channel A, SCSI Id=7, 16/255 SCBs
scsibus0 at ahc0: 16 targets, 8 luns per target     
pcons0 at mainbus0                             
No counter-timer -- using %tick at 333MHz as system clock.
Using %tick -- intr in 3330000 cycles...done.             
scsibus0: waiting 2 seconds for devices to settle...
probe(ahc0:0:0:0): SCB 70 - timed out while idle, SEQADDR == 0x8
SCSIRATE == 0x0                                                 
probe(ahc0:0:0:0): Queuing a BDR SCB
probe(ahc0:0:0:0): SCB 70 - timed out while idle, SEQADDR == 0x45
SCSIRATE == 0x0                                                  
probe(ahc0:0:0:0): no longer in timeout, status = 0
ahc0: Issued Channel A Bus Reset. 1 SCBs aborted   
probe(ahc0:0:0:0): SCB 70 - timed out while idle, SEQADDR == 0x7
SCSIRATE == 0x0                                                 
probe(ahc0:0:0:0): Queuing a BDR SCB
probe(ahc0:0:0:0): SCB 70 - timed out while idle, SEQADDR == 0x8
SCSIRATE == 0x0                                                 
probe(ahc0:0:0:0): no longer in timeout, status = 0
ahc0: Issued Channel A Bus Reset. 1 SCBs aborted   
probe(ahc0:0:0:0): SCB 70 - timed out while idle, SEQADDR == 0x42
SCSIRATE == 0x0                                                  
probe(ahc0:0:0:0): Queuing a BDR SCB
probe(ahc0:0:0:0): SCB 70 - timed out while idle, SEQADDR == 0x9
SCSIRATE == 0x0                                                 
probe(ahc0:0:0:0): no longer in timeout, status = 0
ahc0: Issued Channel A Bus Reset. 1 SCBs aborted   
probe(ahc0:0:0:0): SCB 70 - timed out while idle, SEQADDR == 0x42
SCSIRATE == 0x0                                                  
 0x0                                                  
probe(ahc0:0:0:0): Queuing a BDR SCB
probe(ahc0:0:0:0): SCB 70 - timed out while idle, SEQADDR == 0x44
SCSIRATE == 0x0                                                  
probe(ahc0:0:0:0): no longer in timeout, status = 0
ahc0: Issued Channel A Bus Reset. 1 SCBs aborted   
probe(ahc0:0:0:0): SCB 70 - timed out while idle, SEQADDR == 0xa
SCSIRATE == 0x0                                                 
probe(ahc0:0:0:0): Queuing a BDR SCB
probe(ahc0:0:0:0): SCB 70 - timed out while idle, SEQADDR == 0x43
SCSIRATE == 0x0                                                  
probe(ahc0:0:0:0): no longer in timeout, status = 0
ahc0: Issued Channel A Bus Reset. 1 SCBs aborted