I had the wrong email address in my mail client.
If any one has replied to this email please try emailing me again.
Thanks for your help

On Wednesday 06 November 2002 11:24 pm, Leigh wrote:
> I added 80gig IDE hd to this sunblade 100 while I had debian sparc64 on=
 it
> It was running ok
> After I setup netbsd on this machine it didn't setup my extra HD during
> install, I might not have had it plugged in at the time, not sure..
> Anyway I tried adding it like the instructions say on these URLS
> http://www.netbsd.org/Documentation/misc/#adding-a-disk
> http://www.mclink.it/personal/MG2508/nbsdeng/ap-inst.html
> , but I cant seem to get more then a 80meg partition, when its an 80Gig=
 hd
> Below its a bunch of copy and pastes of what I did.
>
>
>
> ###############################################
> pciide0 at pci0 dev 13 function 0: Acer Labs M5229 UDMA IDE Controller
> (rev. 0xc3)
> pciide0: bus-master DMA support present
> pciide0: primary channel configured to native-PCI mode
> pciide0: using ivec 180c for native-PCI interrupt
> atapibus0 at pciide0 channel 0: 2 targets
> cd0 at atapibus0 drive 1: <LTN486S, , YSU1> type 5 cdrom removable
> cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
> wd0 at pciide0 channel 0 drive 0: <ST315310A>
> wd0: drive supports 16-sector PIO transfers, LBA addressing
> wd0: 14594 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 29888820
> sectors wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5
> (Ultra/100) wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra=
/33)
> (using DMA data transfers)
> cd0(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using =
DMA
> data transfers)
> pciide0: secondary channel configured to native-PCI mode
> wd1 at pciide0 channel 1 drive 0: <Maxtor 6Y080L0>
> wd1: drive supports 16-sector PIO transfers, LBA addressing
> wd1: 78167 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 160086528
> sectors wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6
> wd1(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using =
DMA
> data transfers)
> ###############################################
> disklabel -i -I wd1
> ###############################################
> partition> I
> # Current values:
> # /dev/rwd1c:
> type: ESDI
> disk: Maxtor 6Y080L0
> label: Quantum ProDrive
> flags:
> bytes/sector: 512
> sectors/track: 34
> tracks/cylinder: 6
> sectors/cylinder: 204
> cylinders: 832
> total sectors: 169728
> rpm: 3662
> interleave: 1
> trackskew: 0
> cylinderskew: 0
> headswitch: 0           # microseconds
> track-to-track seek: 0  # microseconds
> drivedata: 0
>
> Disk type [?] [ESDI]:
> Disk name [Maxtor 6Y080L0  ]:
> Label name [Quantum ProDrive]:
> Number of partitions [1]: 8
> Sector size (bytes) [512]:
> Number of sectors per track [34]:
> Number of tracks per cylinder [6]:
> Number of sectors/cylinder [204]:
> Total number of cylinders [832]:
> Total number of sectors [169728]:
> Hardware sectors interleave [1]:
> Sector 0 skew, per track [0]:
> Sector 0 skew, per cylinder [0]:
> Head switch time (usec) [0]:
> Track seek time (usec) [0]:
> partition>
> partition> a
> Filesystem type [?] [4.2BSD]:
> Start offset [0c, 0s, 0M]:
> Partition size ('$' for all remaining) [832c, 169728s, 82.875M]: $
> partition> ?
> ?       print this menu
> C       make partitions contiguous
> E       print disk label and current partition table
> I       change label information
> N       name the label
> P       print current partition table
> Q       quit
> R       rounding (c)ylinders (s)ectors
> W       write the current partition table
> [a-h]   define named partition
> partition> P
> 8 partitions:
> #        size    offset     fstype  [fsize bsize cpg/sgs]
>  a:    169728         0     4.2BSD   1024  8192   336   # (Cyl.    0 - =
831)
>  b:     56712    113016       swap                      # (Cyl.  554 - =
831)
>  c:    169728         0    unknown                      # (Cyl.    0 - =
831)
>  e:    169728         0     4.2BSD   1024  8192   336   # (Cyl.    0 - =
831)
> partition> c
> Filesystem type [?] [unknown]: 4.2BSD
> Start offset [0c, 0s, 0M]:
> Partition size ('$' for all remaining) [832c, 169728s, 82.875M]: $
>  c:    169728         0     4.2BSD      0     0     0   # (Cyl.    0 - =
831)
> partition> e
> Filesystem type [?] [4.2BSD]:
> Start offset [0c, 0s, 0M]:
> Partition size ('$' for all remaining) [832c, 169728s, 82.875M]: $
> partition> w
> Unknown command w
> partition> W
> Label disk [n]? y
> Label written
> partition> Q
> ########################################################