Can the esp0 be set to synchronous? I have a nice hard drive
(18GB) in there and I can't figure out how to set it to sync.

Any tips would be greatly appreciated.

And if you know how fast the le0 can go
is it 10 FD or 100 FD max?

If this is the wrong place/person to ask, is there a
more appropriate place to do so?

TIA:

Here is my dmesg:

syncing disks... done
rebooting

Can't open input device.
SW Inc. SW-40S. , No Keyboard
ROM Rev. 2.4, 40 MB memory installed, Serial #16777132.
Ethernet address 8:0:20:15:af:b, Host ID: 55ffffac.


Rebooting with command:
Boot device: /sbus/esp@0,800000/sd@0,0   File and args: netbsd
>> NetBSD/sparc Secondary Boot, Revision 1.12
>> (autobuild@tgm.daemon.org, Mon Sep  9 08:12:32 UTC 2002)
Booting netbsd
2843368/+100060/+257920/[182704+139344=3D0x36c508
OBP version 2, revision 2.4 (plugin rev 2)
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.=20
All rights reserved.
NetBSD 1.6 (GENERIC) #0: Mon Sep  9 08:27:06 UTC 2002
autobuild@tgm.daemon.org:
/autobuild/sparc/OBJ/autobuild/src/sys/arch/sparc/compile/GENERIC

total memory =3D 40816 KB
avail memory =3D 36132 KB
using 128 buffers containing 512 KB of memory
bootpath: /sbus0/esp@0,800000/sd@0,0
mainbus0 (root): SUNW,Sun 4/75
cpu0 at mainbus0: cache chip bug; trap page uncached:
CY7C601 @ 40 MHz, L64814 FPU
cpu0: 64K byte write-through, 32 bytes/line, hw flush:
cache enabled

memreg0 at mainbus0 ioaddr 0xf4000000
clock0 at mainbus0 ioaddr 0xf2000000: mk48t02: hostid 55ffffac
timer0 at mainbus0 ioaddr 0xf3000000 ipl 10: delay constant 17
auxreg0 at mainbus0 ioaddr 0xf7400003
zs0 at mainbus0 ioaddr 0xf1000000 ipl 12 softpri 6
zstty0 at zs0 channel 0 (console i/o)
zstty1 at zs0 channel 1
zs1 at mainbus0 ioaddr 0xf0000000 ipl 12 softpri 6
kbd0 at zs1 channel 0: baud rate 1200
ms0 at zs1 channel 1: baud rate 1200
audioamd0 at mainbus0 ioaddr 0xf7201000 ipl 13 softpri 4
audio0 at audioamd0: full duplex
sbus0 at mainbus0 ioaddr 0xf8000000: clock =3D 20 MHz
dma0 at sbus0 slot 0 offset 0x400000: dma rev 1+

*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#
esp0 at sbus0 slot 0 offset 0x800000 level 3:
ESP100A, 20MHz, SCSI ID 7

scsibus0 at esp0: 8 targets, 8 luns per target
*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#
le0 at sbus0 slot 0 offset 0xc00000 level 5:
address 08:00:20:15:af:0b

le0: 8 receive buffers, 2 transmit buffers
*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#

SUNW,DBRIe at sbus0 slot 1 offset 0x10000 level 7 not configured
cgsix0 at sbus0 slot 3 offset 0x0 level 7:
SUNW,501-1672, 1152 x 900, rev 8

cgsix0: attached to /dev/fb
fdc0 at mainbus0 ioaddr 0xf7200000 ipl 11 softpri 4: chip 82072
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec

*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#
scsibus0: waiting 2 seconds for devices to settle...
sd0 at scsibus0 target 0 lun 0:
<SEAGATE, ST318418N, 0002> SCSI3 0/direct fixed

sd0: 19001 MB, 26434 cyl, 2 head, 736 sec,
512 bytes/sect x 38914049 sectors

sd0: async, 8-bit transfers, tagged queueing
*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#*#

Kernelized RAIDframe activated
root on sd0a dumps on sd0b
root file system type: ffs
Fri Feb 14 08:22:42 GMT 2003
swapctl: adding /dev/sd0b as swap device at priority 0
Starting file system checks:
/dev/rsd0a: file system is clean; not checking
/dev/rsd0g: file system is clean; not checking
Setting tty flags.
Setting sysctl variables:
Starting network.
Hostname: waste
NIS domainname: localdomain
IPv6 mode: host
Configuring network interfaces: le0.
add net default: gateway 10.0.0.1
Adding interface aliases:
Building databases...
Starting syslogd.
Checking for core dump...
savecore: no core dump
Starting rpcbind.
Mounting all filesystems...
Clearing /tmp.
Creating a.out runtime link editor directory cache.
Checking quotas: done.
Starting mountd.
Starting nfsd.
Starting statd.
Starting lockd.
Setting securelevel: kern.securelevel: 0 -> 1
Starting virecover.
starting local daemons:.
Updating motd.
Starting sshd.
Starting inetd.
Starting cron.
Fri Feb 14 00:23:18 PST 2003

NetBSD/sparc (waste) (console)

login: