On Tue, 16 Apr 2002, Martin Husemann wrote:

> com* at pcmcia?
> 
> I think it used /dev/ttyC*.
> 

Almost there ...

I made an MAKEDEV ttyC0 in dev

and followed the userguide to configure /etc/uucp/port

the HW is apparently recognised properly

==========================================================================
NetBSD 1.5ZC (CLASSIC) #4: Wed Apr 17 02:52:52 BST 2002
    root@bear.dogbert.ntt.it:/home/ftp/pub/NetBSD/src/sys/arch/sparc/compile/CLASSIC
total memory = 65152 KB
avail memory = 58424 KB
using 840 buffers containing 3360 KB of memory
bootpath: /iommu@0,10000000/sbus@0,10001000/espdma@4,8400000/esp@4,8800000/sd@3,0
mainbus0 (root): SUNW,SPARCclassic
cpu0 at mainbus0: TMS390S10 @ 50 MHz, on-chip FPU
cpu0: physical 4K instruction (32 b/l), 2K data (16 b/l): cache enabled
obio0 at mainbus0
clock0 at obio0 slot 0 offset 0x200000: mk48t08: hostid 8070b90a
timer0 at obio0 slot 0 offset 0xd00000 delay constant 23
zs0 at obio0 slot 0 offset 0x100000 level 12 softpri 6
zstty0 at zs0 channel 0
zstty1 at zs0 channel 1
zs1 at obio0 slot 0 offset 0x0 level 12 softpri 6
kbd0 at zs1 channel 0: baud rate 1200 (console input)
ms0 at zs1 channel 1: baud rate 1200
slavioconfig at obio0 slot 0 offset 0x800000 not configured
auxreg0 at obio0 slot 0 offset 0x900000
power0 at obio0 slot 0 offset 0x910000 level 2
fdc0 at obio0 slot 0 offset 0x400000 level 11: no drives attached
iommu0 at mainbus0 addr 0x10000000: version 0x1/0x4, page-size 4096, range 64MB
sbus0 at iommu0: clock = 25 MHz
dma0 at sbus0 slot 4 offset 0x8400000: dma rev 2
esp0 at dma0 slot 4 offset 0x8800000 level 4: ESP200, 40MHz, SCSI ID 7
scsibus0 at esp0: 8 targets, 8 luns per target
audio at sbus0 slot 4 offset 0x1300000 level 7 (ipl 13) not configured
bpp0 at sbus0 slot 4 offset 0xc800000 level 2 (ipl 3): dma rev 2
ledma0 at sbus0 slot 4 offset 0x8400010: dma rev 2
le0 at ledma0 slot 4 offset 0x8c00000 level 6: address 08:00:20:1c:3d:b6
le0: 8 receive buffers, 2 transmit buffers
nell0 at sbus0 slot 1 offset 0x0 level 4 (ipl 7) level 7 (ipl 13): rev 1
pcmcia0 at nell0 socket 0
com0 at pcmcia0 function 0: serial device
com0: ns16550a, working fifo
pcmcia1 at nell0 socket 1
cgthree0 at sbus0 slot 3 offset 0x0 level 9: , 1152 x 900 (console)
cgthree0: attached to /dev/fb
scsibus0: waiting 2 seconds for devices to settle...
sd0 at scsibus0 target 3 lun 0: <CONNER, CP30540  SUN0535, B0CD> SCSI2 0/direct fixed
sd0: 517 MB, 2242 cyl, 6 head, 78 sec, 512 bytes/sect x 1059528 sectors
sd0: sync (100.0ns offset 15), 8-bit (10.000MB/s) transfers, tagged queueing
root on sd0a dumps on sd0b
root file system type: ffs
=============================================================================
but when I do:
cu -p modem

I get:
com0: com_iflush timeout ff
com0: com_iflush timeout ff
com0: com_iflush timeout ff
com0: com_iflush timeout ff
com0: com_iflush timeout ff
then finally 
Connected.
but no answer from the modem.
the modem does work on a ibm thinkpad under linux redhat 7.2 and at least 
some time ago the stp4020 and the same modem were working under Solaris 
2.7

Any suggestions?

-- 
Regards,
Antonio Prioglio [a.prioglio@cbtcentre.co.uk]
http://www.cbtcentre.co.uk
====================================================
Cognitive Behavioural Therapy Centre - London