This is a multi-part message in MIME format.
--------------7AC3B17C6049550C130B2429
Content-Type: text/plain; charset=us-ascii
Content-Transfer-Encoding: 7bit

I've just done a clean install of NetBSD 1.5 on a SPARCstation 1.

I want to run X on it but there are two problems:
1. If I boot with keyboard attached, the PROM monitor gets stuck in an
apparently infinite loop of its 'Type a command' prompt line.
2. If booted with keyboard detached (and reattached) - see boot.log - I
can't start X, receiving the attached diagnostics (x.log)

Any help appreciated,

Toby
--------------7AC3B17C6049550C130B2429
Content-Type: text/plain; charset=us-ascii;
 name="boot.log"
Content-Transfer-Encoding: 7bit
Content-Disposition: inline;
 filename="boot.log"

NetBSD 1.5 (GENERIC) #1: Wed Nov 29 00:29:52 MET 2000
    root@flambard:/usr/src/sys/arch/sparc/compile/GENERIC
total memory = 28620 KB
avail memory = 24660 KB
using 128 buffers containing 512 KB of memory
bootpath: /sbus0/esp0/sd@1,0
mainbus0 (root): Sun 4/60
cpu0 at mainbus0: MB86900/1A or L64801 @ 20 MHz, WTL3170/2 FPU
cpu0: 64K byte write-through, 16 bytes/line, sw flush: cache enabled
memreg0 at mainbus0 ioaddr 0xf4000000
clock0 at mainbus0 ioaddr 0xf2000000: mk48t02 (eeprom)
timer0 at mainbus0 ioaddr 0xf3000000 ipl 10 delay constant 7
auxreg0 at mainbus0 ioaddr 0xf7400000
zs0 at mainbus0 ioaddr 0xf1000000 ipl 12 softpri 6
zstty0 at zs0 channel 0 (console i/o)
zstty1 at zs0 channel 1
zs1 at mainbus0 ioaddr 0xf0000000 ipl 12 softpri 6
kbd0 at zs1 channel 0
ms0 at zs1 channel 1
fdc0 at mainbus0 ioaddr 0xf7200000 ipl 11 softpri 4: chip 82072
audioamd0 at mainbus0 ioaddr 0xf7201000 ipl 13 softpri 4
audio0 at audioamd0: full duplex
sbus0 at mainbus0 ioaddr 0xf8000000: clock = 25 MHz
dma0 at sbus0 slot 0 offset 0x400000: rev 1
esp0 at sbus0 slot 0 offset 0x800000 level 3: ESP100, 25MHz, SCSI ID 7
scsibus0 at esp0: 8 targets, 8 luns per target
le0 at sbus0 slot 0 offset 0xc00000 level 5: address 08:00:20:07:1d:81
le0: 8 receive buffers, 2 transmit buffers
cgthree0 at sbus0 slot 1 offset 0x0 level 7: SUNW,501-1415, 1152 x 900
cgthree0: attached to /dev/fb
scsibus0: waiting 2 seconds for devices to settle...
sd0 at scsibus0 target 1 lun 0: <QUANTUM, P105SS 910-10-94, A.1> SCSI1 0/direct fixed
sd0: 100 MB, 1019 cyl, 6 head, 33 sec, 512 bytes/sect x 205075 sectors
sd1 at scsibus0 target 4 lun 0: <DEC, DSP3210S, 441C> SCSI2 0/direct fixed
sd1: 2049 MB, 3045 cyl, 16 head, 86 sec, 512 bytes/sect x 4197520 sectors
root on sd0a dumps on sd0b
WARNING: preposterous time in file system
WARNING: clock lost 7851 days -- CHECK AND RESET THE DATE!
root file system type: ffs
...

--------------7AC3B17C6049550C130B2429
Content-Type: text/plain; charset=us-ascii;
 name="x.log"
Content-Transfer-Encoding: 7bit
Content-Disposition: inline;
 filename="x.log"


X: Shared object has no run-time symbol table
_X11TransSocketUNIXConnect: Can't connect: errno = 2
_X11TransSocketUNIXConnect: Can't connect: errno = 2
_X11TransSocketUNIXConnect: Can't connect: errno = 2
_X11TransSocketUNIXConnect: Can't connect: errno = 2
_X11TransSocketUNIXConnect: Can't connect: errno = 2
_X11TransSocketUNIXConnect: Can't connect: errno = 2
giving up.
xinit:  No such file or directory (errno 2):  unable to connect to X server
xinit:  No such process (errno 3):  Server error.

--------------7AC3B17C6049550C130B2429--