Salute

When installing from netboot using the generic ip32 on a R5500SC O2,  
after the extraction of the kernel,
the machine begin to display extrange error messages.
all the next stages fails with erros about the disk or the controller.  
to i neet to boot with a diferent kernel image?


sd0(ahc0:0:2:0): adapter resource shortage
sd0(ahc0:0:2:0): adapter resource shortage
sd0(ahc0:0:2:0): adapter resource shortage
sd0(ahc0:0:2:0): adapter resource shortage
sd0(ahc0:0:2:0): adapter resource shortage
sd0(ahc0:0:2:0): adapter resource shortage
sd0(ahc0:0:2:0): adapter resource shortage


Thanks a lot for the people that are working in this port, ive been  
waiting for long time
for this release to give back to live mi shiny O2.

complete boot message here :


 > setenv SystemPartition bootp():
 > boot
Setting $netaddr to 192.168.192.10 (from server DHCPserver)
Obtaining /sash from server DHCPserver
8265808+294092 entry: 0x80069000
[ Kernel symbol table missing! ]
CPU clock speed = 180.00MHz
R5000/Rm5200 SCACHE
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003
     The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
     The Regents of the University of California.  All rights reserved.

NetBSD 1.6ZF (INSTALL32_IP3x) #0: Thu Nov 20 13:22:13 JST 2003
          
wileyc@izu:/usr/builder/sgimips-rel/obj/sys/arch/sgimips/compile/ 
INSTALx
128 MB memory, 103 MB free, 6848 KB for ARCS, 6656 KB in 1664 buffers
mainbus0 (root): SGI-IP32 [SGI, 8], 1 processor
cpu0 at mainbus0: MIPS R5000 CPU (0x2321) Rev. 2.1 with built-in FPU  
Rev. 1.0
cpu0: 32KB/32B 2-way set-associative L1 Instruction cache, 48 TLB  
entries
cpu0: 32KB/32B 2-way set-associative write-back L1 Data cache
cpu0: 512KB/32B direct-mapped write-through L2 Unified cache
crime0 at mainbus0 addr 0x14000000: rev 1.1 (CRIME_ID: a1)
mace0 at mainbus0 addr 0x1f000000
com0 at mace0 offset 0x390000 intr 4 intrmask 0x3f00000: ns16550a,  
working fifo
com0: console
mace: established interrupt 4 (level 3f00000)
com1 at mace0 offset 0x398000 intr 4 intrmask 0xfc000000: ns16550a,  
working fifo
mace: established interrupt 4 (level fc000000)
pckbc0 at mace0 offset 0x320000 intr 5 intrmask 0x0
lpt0 at mace0 offset 0x380000 intr 4 intrmask 0xf0000
mace: established interrupt 4 (level f0000)
mcclock0 at mace0 offset 0x3a0000 intrmask 0x0
macepci0 at mace0 offset 0x80000 intr 7 intrmask 0x0: rev 1
pci_addr_fixup: 000:01:0 0x9004 0x8078 new address 0x00001000 (size  
0x100)
pci_addr_fixup: 000:01:0 0x9004 0x8078 new address 0x80100000 (size  
0x1000)
pci_addr_fixup: 000:02:0 0x9004 0x8078 new address 0x00002000 (size  
0x100)
pci_addr_fixup: 000:02:0 0x9004 0x8078 new address 0x80200000 (size  
0x1000)
mace: established interrupt 7 (level 0)
pci0 at macepci0 bus 0
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
ahc0 at pci0 dev 1 function 0
ahc0: interrupting at crime interrupt 8
ahc0: Host Adapter Bios disabled.  Using default SCSI device parameters
ahc0: aic7880: Wide Channel A, SCSI Id=7, 16/253 SCBs
scsibus0 at ahc0: 16 targets, 8 luns per target
ahc1 at pci0 dev 2 function 0
ahc1: interrupting at crime interrupt 9
ahc1: Host Adapter Bios disabled.  Using default SCSI device parameters
ahc1: aic7880: Wide Channel A, SCSI Id=7, 16/253 SCBs
scsibus1 at ahc1: 16 targets, 8 luns per target
biomask 07 netmask 07 ttymask 07 clockmask 87
md0: internal 4096 KB image area
scsibus0: waiting 2 seconds for devices to settle...
scsibus1: waiting 2 seconds for devices to settle...
sd0 at scsibus0 target 2 lun 0: <HP, 2.13GB A 80-0430, 0430> disk fixed
sd0: 2033 MB, 5168 cyl, 5 head, 161 sec, 512 bytes/sect x 4165252  
sectors
sd0: sync (100.00ns offset 8), 16-bit (20.000MB/s) transfers, tagged  
queueing
cd0 at scsibus0 target 4 lun 0: <TOSHIBA, CD-ROM XM-5401TA, 3605> cdrom  
removabe
cd0: sync (236.00ns offset 15), 8-bit (4.237MB/s) transfers
boot device: <unknown>
root on md0a dumps on md0b
WARNING: clock gained 2 days -- CHECK AND RESET THE DATE!
root file system type: ffs
Terminal type? [vt100]