On DSM-G600 issues with WPA_SUPPLICANT, CDROM on USB port, ntfs module.

To: port-sandpoint%netbsd.org@localhost
Subject: On DSM-G600 issues with WPA_SUPPLICANT, CDROM on USB port, ntfs module.
From: Charles Brown <obigiankenobi%gmail.com@localhost>
Date: Sun, 5 Feb 2012 19:49:56 +0100
Hi,
I'm testing some NetBSD features on my sandpoint DSM-G600 (kernel 5.99.64),
and I've found some issues:

1) When I try to connect usb keys or external hard disks via USB (both
with an ext2 filesystem) , everything works fine.
If I try to connect a portable CDROM (with external power) on USB
ports , I have this messages:

umass0 at uhub2 port 1 configuration 1 interface 0
umass0: vendor 0x05e3 USB TO IDE, rev 2.00/0.33, addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 1 lun per target
scsibus0 target 0 lun 0: <_NEC, DVD+-RW ND-6650A, 2.N0> cdrom
removable not configured

Ok, support for removables cd-rom is not configured (hope it will be
in the next future),
but after a minute, also this message appears in console:

dsm-g600# acardide0:0:0: lost interrupt
        type: ata tc_bcount: 16384 tc_skip: 0
acardide0:0:0: bus-master DMA error: missing interrupt, status=0x29
wd0a: DMA error writing fsbn 138520576 of 138520576-138520607 (wd0 bn
138520639; cn 137421 tn 4 sn 19), retrying
wd0: soft error (corrected)

IRQ conflict?
after this, the hd unit seems to work well.
No problem if the cdrom unit is already connected at boot time.

2) wpa_supplicant takes very long time in associating with wireless router:
Router is tp-link tl-mr3420 firmware 3.12.8 with WPA2-PSK AES enabled.
My wpa_supplicant.conf:

ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=wheel

network={
        ssid="homegroup"
        scan_ssid=1
#       key_mgmt=WPA-PSK
#       proto=RSN WPA
#       pairwise=CCMP TKIP
         psk="mysecrethere"
}Hi,
I'm testing some NetBSD features on my sandpoint DSM-G600 (kernel 5.99.64),
and I've found some issues:

1) When I try to connect usb keys or external hard disks via USB (both
with an ext2 filesystem) , everything works fine.
If I try to connect a portable CDROM (with external power) on USB
ports , I have this messages:

umass0 at uhub2 port 1 configuration 1 interface 0
umass0: vendor 0x05e3 USB TO IDE, rev 2.00/0.33, addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 1 lun per target
scsibus0 target 0 lun 0: <_NEC, DVD+-RW ND-6650A, 2.N0> cdrom
removable not configured

Ok, support for removables cd-rom is not configured (hope it will be
in the next future),
but after a minute, also this message appears in console:

dsm-g600# acardide0:0:0: lost interrupt
        type: ata tc_bcount: 16384 tc_skip: 0
acardide0:0:0: bus-master DMA error: missing interrupt, status=0x29
wd0a: DMA error writing fsbn 138520576 of 138520576-138520607 (wd0 bn
138520639; cn 137421 tn 4 sn 19), retrying
wd0: soft error (corrected)

IRQ conflict?
after this, the hd unit seems to work well.
No problem if the cdrom unit is already connected at boot time.

2) wpa_supplicant takes very long time in associating with wireless router:
Router is tp-link tl-mr3420 firmware 3.12.8 with WPA2-PSK AES enabled.
My wpa_supplicant.conf:

ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=wheel

network={
        ssid="homegroup"
        scan_ssid=1
#       key_mgmt=WPA-PSK
#       proto=RSN WPA
#       pairwise=CCMP TKIP
         psk="mysecrethere",
I'm testing some NetBSD features on my sandpoint DSM-G600 (kernel 5.99.64),
and I've found some issues:

1) When I try to connect usb keys or external hard disks via USB (both
with an ext2 filesystem) , everything works fine.
If I try to connect a portable CDROM (with external power) on USB
ports , I have this messages:

umass0 at uhub2 port 1 configuration 1 interface 0
umass0: vendor 0x05e3 USB TO IDE, rev 2.00/0.33, addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 1 lun per target
scsibus0 target 0 lun 0: <_NEC, DVD+-RW ND-6650A, 2.N0> cdrom
removable not configured

Ok, support for removables cd-rom is not configured (hope it will be
in the next future),
but after a minute, also this message appears in console:

dsm-g600# acardide0:0:0: lost interrupt
        type: ata tc_bcount: 16384 tc_skip: 0
acardide0:0:0: bus-master DMA error: missing interrupt, status=0x29
wd0a: DMA error writing fsbn 138520576 of 138520576-138520607 (wd0 bn
138520639; cn 137421 tn 4 sn 19), retrying
wd0: soft error (corrected)

IRQ conflict?
after this, the hd unit seems to work well.
No problem if the cdrom unit is already connected at boot time.

2) wpa_supplicant takes very long time in associating with wireless router:
Router is tp-link tl-mr3420 firmware 3.12.8 with WPA2-PSK AES enabled.
My wpa_supplicant.conf:

ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=wheel

network={
        ssid="homegroup"
        scan_ssid=1
#       key_mgmt=WPA-PSK
#       proto=RSN WPA
#       pairwise=CCMP TKIP
         psk="mysecrethere"
}

Starting wpa_supplicant:

dsm-g600# wpa_supplicant -i ral0 -c /etc/wpa_supplicant.conf
Trying to associate with 74:ea:3a:b1:83:30 (SSID='homegroup' freq=2452 MHz)
Associated with 74:ea:3a:b1:83:30
CTRL-EVENT-DISCONNECTED bssid=74:ea:3a:b1:83:30 reason=0
Trying to associate with 74:ea:3a:b1:83:30 (SSID='homegroup' freq=2452 MHz)
Associated with 74:ea:3a:b1:83:30
CTRL-EVENT-DISCONNECTED bssid=74:ea:3a:b1:83:30 reason=0
........
........
........ 15/30 minutes of retries
........
........
CTRL-EVENT-DISCONNECTED bssid=74:ea:3a:b1:83:30 reason=0
Trying to associate with 74:ea:3a:b1:83:30 (SSID='homegroup' freq=2452 MHz)
Associated with 74:ea:3a:b1:83:30
CTRL-EVENT-DISCONNECTED bssid=74:ea:3a:b1:83:30 reason=0
Trying to associate with 74:ea:3a:b1:83:30 (SSID='homegroup' freq=2452 MHz)
Associated with 74:ea:3a:b1:83:30
CTRL-EVENT-DISCONNECTED bssid=74:ea:3a:b1:83:30 reason=0
Trying to associate with 74:ea:3a:b1:83:30 (SSID='homegroup' freq=2452 MHz)
Associated with 74:ea:3a:b1:83:30
WPA: Key negotiation completed with 74:ea:3a:b1:83:30 [PTK=CCMP GTK=CCMP]
CTRL-EVENT-CONNECTED - Connection to 74:ea:3a:b1:83:30 completed
(auth) [id=0 id_str=]

When connected, everything works fine, I obtain my ip address via dhcp
and the connection is fast and reliable.
Timeout problem during authentication?

3) Can't load /stand/sandpoint/5.99.64/modules/ntfs/ntfs.kmod:

modload: Operation not permitted.

Hope I'm not so boring...

Please Help!!! :)

Thank you very much.

G.
}

Starting wpa_supplicant:

dsm-g600# wpa_supplicant -i ral0 -c /etc/wpa_supplicant.conf
Trying to associate with 74:ea:3a:b1:83:30 (SSID='homegroup' freq=2452 MHz)
Associated with 74:ea:3a:b1:83:30
CTRL-EVENT-DISCONNECTED bssid=74:ea:3a:b1:83:30 reason=0
Trying to associate with 74:ea:3a:b1:83:30 (SSID='homegroup' freq=2452 MHz)
Associated with 74:ea:3a:b1:83:30
CTRL-EVENT-DISCONNECTED bssid=74:ea:3a:b1:83:30 reason=0
........
........
........ 15/30 minutes of retries
........
........
CTRL-EVENT-DISCONNECTED bssid=74:ea:3a:b1:83:30 reason=0
Trying to associate with 74:ea:3a:b1:83:30 (SSID='homegroup' freq=2452 MHz)
Associated with 74:ea:3a:b1:83:30
CTRL-EVENT-DISCONNECTED bssid=74:ea:3a:b1:83:30 reason=0
Trying to associate with 74:ea:3a:b1:83:30 (SSID='homegroup' freq=2452 MHz)
Associated with 74:ea:3a:b1:83:30
CTRL-EVENT-DISCONNECTED bssid=74:ea:3a:b1:83:30 reason=0
Trying to associate with 74:ea:3a:b1:83:30 (SSID='homegroup' freq=2452 MHz)
Associated with 74:ea:3a:b1:83:30
WPA: Key negotiation completed with 74:ea:3a:b1:83:30 [PTK=CCMP GTK=CCMP]
CTRL-EVENT-CONNECTED - Connection to 74:ea:3a:b1:83:30 completed
(auth) [id=0 id_str=]

When connected, everything works fine, I obtain my ip address via dhcp
and the connection is fast and reliable.
Timeout problem during authentication?

3) Can't load /stand/sandpoint/5.99.64/modules/ntfs/ntfs.kmod:

modload: Operation not permitted.

Hope I'm not so boring...

Please Help!!! :)

Thank you very much.

G.

Starting wpa_supplicant:

dsm-g600# wpa_supplicant -i ral0 -c /etc/wpa_supplicant.conf
Trying to associate with 74:ea:3a:b1:83:30 (SSID='homegroup' freq=2452 MHz)
Associated with 74:ea:3a:b1:83:30
CTRL-EVENT-DISCONNECTED bssid=74:ea:3a:b1:83:30 reason=0
Trying to associate with 74:ea:3a:b1:83:30 (SSID='homegroup' freq=2452 MHz)
Associated with 74:ea:3a:b1:83:30
CTRL-EVENT-DISCONNECTED bssid=74:ea:3a:b1:83:30 reason=0
........
........
........ 15/30 minutes of retries
........
........
CTRL-EVENT-DISCONNECTED bssid=74:ea:3a:b1:83:30 reason=0
Trying to associate with 74:ea:3a:b1:83:30 (SSID='homegroup' freq=2452 MHz)
Associated with 74:ea:3a:b1:83:30
CTRL-EVENT-DISCONNECTED bssid=74:ea:3a:b1:83:30 reason=0
Trying to associate with 74:ea:3a:b1:83:30 (SSID='homegroup' freq=2452 MHz)
Associated with 74:ea:3a:b1:83:30
CTRL-EVENT-DISCONNECTED bssid=74:ea:3a:b1:83:30 reason=0
Trying to associate with 74:ea:3a:b1:83:30 (SSID='homegroup' freq=2452 MHz)
Associated with 74:ea:3a:b1:83:30
WPA: Key negotiation completed with 74:ea:3a:b1:83:30 [PTK=CCMP GTK=CCMP]
CTRL-EVENT-CONNECTED - Connection to 74:ea:3a:b1:83:30 completed
(auth) [id=0 id_str=]

When connected, everything works fine, I obtain my ip address via dhcp
and the connection is fast and reliable.
Timeout problem during authentication?

3) Can't load /stand/sandpoint/5.99.64/modules/ntfs/ntfs.kmod:

modload: Operation not permitted.

Hope I'm not so boring...

Please Help!!! :)

Thank you very much.

G.
Follow-Ups:
- Re: On DSM-G600 issues with WPA_SUPPLICANT, CDROM on USB port, ntfs module.
  - From: Frank Wille
Prev by Date: Re: Kernel panic in netbsd 5.99.63 in D-LINK DSM-G600
Next by Date: Re: On DSM-G600 issues with WPA_SUPPLICANT, CDROM on USB port, ntfs module.
Previous by Thread: Kernel panic in netbsd 5.99.63 in D-LINK DSM-G600
Next by Thread: Re: On DSM-G600 issues with WPA_SUPPLICANT, CDROM on USB port, ntfs module.
Indexes:
Home | Main Index | Thread Index | Old Index