Hi all,

	Thanks to those for earlier comments regarding my setup..

	(It's 5/240 w/ 196 Mb RAM booting off a SCSI disk w/ dd'd blocks
from diskimage.tar.gz (if memory serves) and a TC enet card.)

	Anyway, I removed the TC card and the kernel gets _much_ farther,
but I get a memory error now.  I'll remove some of the mem in the 
morning when I get to the office (right now I'm using ssh and tip 
from home) .. but I'm wondering if someone can decode some this 
output for me:

(here's the boot sequence, followed by the full test output I did -
when I suspect mem probs)

Does this suggest a prob w/ the 5th mem board? BTW - there are 6x32Mb
modules in the box.

Thanks!
--
>>boot 3/rz2/netbsd
>> NetBSD/pmax Secondary Boot, Revision 1.0
>> (root@vlad, Fri Jul 16 12:48:23 EST 1999)
Boot: 3/rz2/netbsd
989544+2142608+143892 [89+50384+39543]=0x336ef4
Starting at 0x80030000

Copyright (c) 1996, 1997, 1998, 1999
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 1.4.1 (RAMDISK) #15: Sat Jul 17 02:18:16 EST 1999
    root@vlad:/usr/src/sys/arch/pmax/compile/RAMDISK
DECstation 5000/240 (3MAXPLUS)
real mem  = 201326592
avail mem = 172277760
using 4915 buffers containing 20131840 bytes of memory
mainbus0 (root)
cpu0 at mainbus0: cpu0: MIPS R3000 CPU Rev. 3.0 with MIPS R3010 FPC Rev. 4.0
cpu0: 64kb Instruction, 64kb Data, direct mapped cache
tc0 at mainbus0: 25 MHz clock
ioasic0 at tc0 slot 3 offset 0x0
le0 at ioasic0 offset 0xc0000: address 08:00:2b:2a:7c:46
le0: 32 receive buffers, 8 transmit buffers
scc0 at ioasic0 offset 0x100000
scc1 at ioasic0 offset 0x180000: console
mcclock0 at ioasic0 offset 0x200000: mc146818 or compatible
asc0 at ioasic0 offset 0x300000: target 7
Beginning old-style SCSI device autoconfiguration
CPU memory write ECC error at 0x0bfff61c
   ECC 0xcc99ba2e

panic: panic("Mem error interrupt");

halted.

>>test
?TFL:  3/mem (1: board 5, MBE= 4194304, SBE= 0) [KN03-AA]
3/misc/kbd                    
?STF (4: Ln#0 Kbd self test)

3/misc/mouse                  
?STF (4: Ln#1 Pntr self test)

?TFL:  3/ni/ext-lb (3:(xmt [00000006, 00000040] cable)) [KN03-AA]
?TFL:  3/mem (1: board 5, MBE= 4194304, SBE= 0) [KN03-AA]
?STF (4: Ln#0 Kbd self test)
?STF (4: Ln#1 Pntr self test)
?TFL:  3/ni/ext-lb (3:(xmt [00000006, 00000040] cable)) [KN03-AA]
>>
-- 
Regards,
Richard