--cWoXeonUoKmBZSoM
Content-Type: text/plain; charset=us-ascii
Content-Disposition: inline

On Wed, Aug 09, 2006 at 06:38:56PM +0200, Martin Husemann wrote:
> Below is a dmesg from mine.

Eh, here it is.

Martin

--cWoXeonUoKmBZSoM
Content-Type: text/plain; charset=us-ascii
Content-Disposition: attachment; filename="dmesg.boot"

Loaded initial symtab at 0x802ebd74, strtab at 0x80300c78, # entries 5258
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 3.99.20 (MTX-1) #4: Wed Jun  7 18:36:40 CEST 2006
	martin@night-porter.duskware.de:/usr/src/sys/arch/evbmips/compile/MTX-1
4G Systems MTX-1
total memory = 65536 KB
avail memory = 60520 KB
mainbus0 (root)
cpu0 at mainbus0: 324.00MHz (hz cycles = 632813, delay divisor = 324)
cpu0: Alchemy Au1500 (Rev 2 core) (0x1030202) Rev. 2 with software emulated floating point
cpu0: 16KB/32B 4-way set-associative L1 Instruction cache, 32 TLB entries
cpu0: 16KB/32B 4-way set-associative write-back L1 Data cache
obio0 at mainbus0
aubus0 at mainbus0
aucom0 at aubus0 addr 0x11100000 irq 0: Au1X00 UART, working fifo
aucom0: console
aucom1 at aubus0 addr 0x11400000 irq 3: Au1X00 UART, working fifo
aurtc0 at aubus0: Au1X00 programmable clock
aumac0 at aubus0 addr 0x11500000 irq 28: Au1X00 10/100 Ethernet
aumac0: Ethernet address 00:0e:56:00:02:2c
sqphy0 at aumac0 phy 31: Seeq 84220 10/100 media interface, rev. 0
sqphy0: using Seeq 84220 isolate/reset hack
sqphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
aumac1 at aubus0 addr 0x11510000 irq 29: Au1X00 10/100 Ethernet
aumac1: Ethernet address 00:0e:56:00:12:2c
ohci0 at aubus0 addr 0x10100000 irq 26: Alchemy OHCI
ohci0: OHCI version 1.0
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: vendor 0x0000 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
aupci0 at aubus0 addr 0x14005000: Alchemy Host-PCI Bridge, 66MHz
pci0 at aupci0 bus 0
pci0: i/o space, memory space enabled
wi0 at pci0 dev 0 function 0: Intersil PRISM2.5 Mini-PCI WLAN (rev. 0x01)
wi0: interrupting at irq 1
wi0: 802.11 address 00:90:4b:0a:de:81
wi0: using RF:PRISM2.5 MAC:ISL3874A(Mini-PCI)
wi0: Intersil Firmware: Primary (1.1.1), Station (1.7.4)
wi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
augpio0 at aubus0 addr 0x11900100: Alchemy GPIO, primary block
gpio0 at augpio0: 23 pins
augpio1 at aubus0 addr 0x11700000: Alchemy GPIO, secondary block
gpio1 at augpio1: 16 pins
uhub0: device problem, disabling port 1
root on aumac0
nfs_boot: trying DHCP/BOOTP
...

--cWoXeonUoKmBZSoM--