This is a multi-part message in MIME format.
--------------000700090407060304030009
Content-Type: text/plain; charset=us-ascii; format=flowed
Content-Transfer-Encoding: 7bit

Hello port-macppc,

Scouring groups.google.com revealed this page:
http://lists.linuxppc.org/linuxppc-user/200005/msg01454.html
Which is an excellent resource.  Unforchunately cat'ing a file to 
/dev/adb gives me: "cat: stdout: Operation not supported by device"
Granted these are two architectualy different platforms, I thought I'd 
get lucky.  How do you get an old-world (or new-world for that matter) 
mac (or clone) to turn it self on when power is applied?

On the second note; the ex drive won't switch into full-duplex mode via 
ifconfig.  It gives me:
# ifconfig ex0 media-opt full-duplex
ifconfig: media-opt: bad value
Any clues on this one?  I can't seem to get the media-opt flag to 
anything.  I can set the media though, with a delay of 5 seconds or so.


This machine is a PowerComputing PowerBase 200.  dmesg attached.


-- 
Jesse Peterson  /  jesse@pixeltechs.com

--------------000700090407060304030009
Content-Type: text/plain;
 name="dmesg"
Content-Transfer-Encoding: 7bit
Content-Disposition: inline;
 filename="dmesg"

NetBSD 1.6 (GENERIC) #0: Sun Sep  8 22:04:33 UTC 2002
    autobuild@tgm.daemon.org:/autobuild/macppc/OBJ/autobuild/src/sys/arch/macppc/compile/GENERIC
total memory = 98304 KB
avail memory = 83180 KB
using 1254 buffers containing 5016 KB of memory
mainbus0 (root)
cpu0 at mainbus0: 603ev (Revision 2.1), ID 0 (primary)
cpu0: HID0 90c001<DOZE,DPM,ICE,DCE,NOPTI>
cpu0: ohare L2 cache enabled
bandit0 at mainbus0
pci0 at bandit0 bus 0
pci0: i/o space, memory space enabled
pchb0 at pci0 dev 11 function 0
pchb0: Apple Computer Bandit Host-PCI Bridge (rev. 0x03)
ex0 at pci0 dev 13 function 0: 3Com 3c905-TX 10/100 Ethernet (rev. 0x0)
ex0: interrupting at irq 23
ex0: MAC address 00:60:08:3f:fc:d4
nsphy0 at ex0 phy 24: DP83840 10/100 media interface, rev. 1
nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
obio0 at pci0 dev 16 function 0: addr 0xf3000000
mesh0 at obio0 offset 0x10000 irq 12: 50MHz, SCSI ID 7
scsibus0 at mesh0: 8 targets, 8 luns per target
zsc0 at obio0 offset 0x13000: irq 15,16
zstty0 at zsc0 channel 0 (console)
zstty1 at zsc0 channel 1
awacs at obio0 offset 0x14000 not configured
swim3 at obio0 offset 0x15000 not configured
nvram0 at obio0 offset 0x60000
adb0 at obio0 offset 0x16000 irq 18: 0 targets
aed0 at adb0 addr 0: ADB Event device
wdc0 at obio0 offset 0x20000 irq property not found; using 13: DMA transfer
ofb0 at pci0 dev 17 function 0: ATI Technologies 3D Rage I/II
ofb0: 640 x 480, 8bpp
wsdisplay0 at ofb0 kbdmux 1
wsmux1: connecting to wsdisplay0
scsibus0: waiting 2 seconds for devices to settle...
sd0 at scsibus0 target 0 lun 0: <IBM, DDRS-34560, S97B> SCSI2 0/direct fixed
sd0: 4357 MB, 8387 cyl, 5 head, 212 sec, 512 bytes/sect x 8925000 sectors
cd0 at scsibus0 target 3 lun 0: <PHILIPS, PCA80SC, V4-2> SCSI2 5/cdrom removable
boot device: sd0
root on sd0a dumps on sd0b
root file system type: ffs

--------------000700090407060304030009--