I'm having a problem booting into NetBSD after the installation. I get
to the last screen shown here and i select (d) to reboot.

-------------------------------------------------------------------------------------
 Welcome to sysinst, the NetBSD-1.4 system installation tool.
 This menu-driven tool is designed to help you install NetBSD to a hard
 disk, or upgrade an existing NetBSD system, with a minimum of work.
 In the following menus, you may change the current selection by
 either typing the reference letter (a, b, c, ...).  Arrow keys may also work.
 You activate the current selection from the menu by typing the enter key.
 
 If you booted from a floppy, you may now remove the disk.

 Thank you for using NetBSD!
 
               *************************************************
               *  NetBSD-1.4 Install System                    *
               *                                               *
               *>a: Install NetBSD to hard disk                *
               * b: Upgrade NetBSD on a hard disk              *
               * c: Re-install sets or install additional sets *
               * d: Reboot the computer                        *
               * e: Utility menu                               *
               * f: Exit Install System                        *
               *************************************************


-------------------------------------------------------------------------------------

After I reboot nothing happens. I have a couple of questions. 1) do I
need to go into the shell after this installation screen and configure
something? 2) what "exactly" should I enter into BootVariables to have
my computer boot from the internal SCSI disk ID (1) on the internal SCSI
bus (0)? 3) I have a 9500/180 with an ATImach64 video card but how do I
specify that to be my video out? Nothing seems to stick, it always gets
reset. 

Here' my output from my first boot that I did get to work. It stops
right at the end at "db>" What do I do?

-------------------------------------------------------------------------------------
RESETing to change Configuration!

>> NetBSD/macppc OpenFirmware Boot, Revision 1.2
>> (matt@yosemite.local, Wed Jun 21 18:05:29 PDT 2000)
1871644+175984 [100+78720+64345]=0x217058
 start=0x100000
Copyright (c) 1996, 1997, 1998, 1999, 2000
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 1.4.2 (GENERIC) #0: Wed Mar 15 21:53:17 PST 2000
    toddpw@leia.toddpw.net:/usr/src/sys/arch/macppc/compile/GENERIC
CPU: 604ev (Revision 202)
real mem  = 167772160
avail mem = 149905408
using 2048 buffers containing 8388608 bytes of memory
no active packagemainbus0 (root)
cpu0 at mainbus0
pci0 at mainbus0 bus 0
pci0: i/o enabled, memory enabled
pchb0 at pci0 dev 11 function 0
pchb0: Apple Computer PCI Controller (rev. 0x03)
Brooktree Bt848 Video Capture (video multimedia, revision 0x12) at pci0
dev 13 f
unction 0 not configured
unknown vendor 0x4f4d product 0x0400 (miscellaneous bridge) at pci0 dev
15 funct
ion 0 not configured
obio0 at pci0 dev 16 function 0: addr 0xf3000000
esp0 at obio0 offset 0x10000 irq 12: NCR53C94, 25MHz, SCSI ID 7
scsibus0 at esp0: 8 targets, 8 luns per target
sd0 at scsibus0 targ 5 lun 0: <IOMEGA, ZIP 100, D.09> SCSI2 0/direct removable
esp0: illegal command: 0x42 (state 2, phase 3, prevphase 1)
esp0: SCSI bus reset
sd0: drive offline
esp0: illegal command: 0x42 (state 2, phase 3, prevphase 1)
esp0: SCSI bus reset
mc0 at obio0 offset 0x11000: irq 14,2,3: address 00:a0:40:46:17:28
zsc0 at obio0 offset 0x13000: irq 15,16
zstty0 at zsc0 channel 0 (console)
zstty1 at zsc0 channel 1
awacs at obio0 offset 0x14000 not configured
swim3 at obio0 offset 0x15000 not configured
adb0 at obio0 offset 0x16000 irq 18: 4 targets
aed0 at adb0 addr 0: ADB Event device
akbd0 at adb0 addr 2: adjustable keypad
wskbd0 at akbd0
ams0 at adb0 addr 3: 1-button, 100 dpi mouse
wsmouse0 at ams0
adb0 addr 7: misc. device (remote control?) (2) unsupported
akbd1 at adb0 addr 2: adjustable keyboard
wskbd at akbd1 not configured
mesh0 at obio0 offset 0x18000 irq 13: 50MHz, SCSI ID 7
scsibus1 at mesh0: 8 targets, 8 luns per target
sd1 at scsibus1 targ 0 lun 0: <SEAGATE, ST32151N, 0560> SCSI2 0/direct fixed
sd1: 2047MB, 4177 cyl, 8 head, 125 sec, 512 bytes/sect x 4193415 sectors
sd2 at scsibus1 targ 1 lun 0: <HP, C3724S, 6039> SCSI2 0/direct fixed
sd2: 1149MB, 3703 cyl, 5 head, 127 sec, 512 bytes/sect x 2354660 sectors
cd0 at scsibus1 targ 3 lun 0: <MATSHITA, CD-ROM CR-8008, 8.0h> SCSI2
5/cdrom rem
ovable
nvram0 at obio0 offset 0x1d000
pci1 at mainbus0 bus 1
pci1: i/o enabled, memory enabled
pchb1 at pci1 dev 11 function 0
pchb1: Apple Computer PCI Controller (rev. 0x03)
3Dfx Interactive Voodoo (video multimedia, revision 0x02) at pci1 dev 14 functio
n 0 not configured
ofb0 at pci1 dev 15 function 0trap type 300 at ff80aaa8
Stopped in  at  0x23350c:       lwz r0, r1, 0x14,
db>