Thanks Roger,

I do not understand why the
kern_sbc.tgz is not present in the
"/pub/unix/BSD/NetBSD/NetBSD-1.4.2/mac68k/binary/sets"
but exists in
"/pub/unix/BSD/NetBSD/NetBSD-1.4.1/mac68k/binary/sets"

finaly i have installed the 1.4.5 ALPHA2
with the kernel netbsd.GENERICSBC-60.tar.gz
and it wors perfectly (just some parity errors
on the scsi of the cdrom, maybe because no cdrom is
inserted ?! after the boot, i have no problem mounting
and reading an iso cdrom)

so the next step for me is to find and install
two etehernet adapters and to install / run rp-pppoe for
a connexion to an adsl line (this IIVX will act as
a router / firewall)

Christophe


Roger Brown wrote:
> 
> Hi,
> 
> This is the kernel I use on my IIvx, it's from a snapshot a few weeks after
> the release of 1.4.2.
> 
> Good luck,
> 
> Roger
> ----------
> >From: Christophe Pedretti <cpedretti@ptc.com>
> >To: port-mac68k@netbsd.org
> >Subject: Booting NetBSD 1.4.2 on a IIVX
> >Date: Wed, Oct 25, 2000, 2:55 am
> >
> 
> >Hello,
> >
> >i have exactly the same problem (same hardware: 2VX with a quantum
> >hard drive) with the same error messages (parity errors with
> >the sbc kernel and unexpected phase change error with the generic
> >kernel) except that i am running netbSD 1.4.2
> >
> >I have tried the 1.4.5 ALPHA2 release (only the generci kernel:
> >netbsd.GENERIC-60.tar.gz),
> >the problem is still here.....
> >
> >can you help me ? which kernel i can try ?
> >
> >-rw-r--r--   1 ftp      ftp       1076384 Oct  3 13:27 netbsd.GENERIC-59.tar.gz
> >-rw-r--r--   1 ftp      ftp       1076226 Oct 13 04:12 
> >-rw-r--r--   1 ftp      ftp       1076379 Oct  3 13:28 netbsd.GENERICSBC-59.tar.gz
> >-rw-r--r--   1 ftp      ftp       1076389 Oct 13 04:12 netbsd.GENERICSBC-60.tar.gz
> >-rw-r--r--   1 ftp      ftp       1075606 Oct  3 13:29 netbsd.MRG-59.tar.gz
> >-rw-r--r--   1 ftp      ftp       1075560 Oct 13 04:12 netbsd.MRG.tar.gz
> >-rw-r--r--   1 ftp      ftp       1075768 Oct  3 13:30 netbsd.MRGSBC-59.tar.gz
> >-rw-r--r--   1 ftp      ftp       1075661 Oct 13 04:12 netbsd.MRGSBC.tar.gz
> >
> >someone has alreday resolved similar problem ?
> >
> >thanks in advance
> >
> >
> >--
> >Christophe
> >
> >
> >
> >>
> >>
> >> Hello,
> >>
> >> I have been running 1.4.1 on a IIcx with no problem, but now I have been
> >> trying to use 1.4.1 on
> >> a IIvx.
> >>
> >> If I run with sbc kernel then I get continual messages saying:
> >>
> >> sbc0: parity error
> >>
> >> what device is sbc0?
> >>
> >> If I run with the generic kernel I get tons of the following:
> >>
> >> Unexpected phase chnage.
> >> scsi_show: scsi_main is not running
> >> REQ-CONNECTED: 0 0x1550000[8192] cmd[0]=a S=0 Nff R=0 resid=8192 dr_flag=1
> >> Bus signals (7c/00): I/OIC/D|MSG|REG|BSY
> >> Dma status (30): IRQ|EPAR
> >> phase = 0, busy:1, spl:2204
> >>     0    scsi_main5
> >>     1    pdma_cleanup2
> >>     2    scsi_main1
> >>     3    scsi_select
> >>     4    tpio1
> >>     5    tpio2
> >>     6    scsi_select10
> >>     7    info_transf1
> >>     8    tpio1
> >>     9    tpio2
> >>     10   info_transf5
> >>     11   info_transf1
> >>     12   info_transf3
> >>     13   transfer_pdma0
> >>     14   waiting for interrupt.
> >>     15   scsi_main3
> >>     16   scsi_main4
> >>     17   scsi_main5
> >>     18   drq (out)
> >>     19   write complete
> >>     20   read a byte to force a phase change
> >>     21   end drq
> >>     22   irq
> >>     23   pdma_ready0
> >>     24   pdma_ready1
> >>
> >> This happens on two QUANTUM drives I have, and I have also tried
> >> initialising one drive from scratch using Apples Drive Setup and MKFS 1.45
> >>
> >> Where can I go from here?
> >>
> >> Thanks
> >>
> >> Roger Brown
> >
> >
> >--
> >Christophe

-- 
Christophe