Here is the dmesg with

boot -d
write atadebug_mask 0x10
c

as requested. Again, note that wd0 is the PCMCIA flash card that I
inserted to get the dmesg.

Thanks!


Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 4.0_RC4 (INSTALL_LARGE) #0: Thu Nov  8 03:38:38 PST 2007
	builds@wb34:/home/builds/ab/netbsd-4-0-RC4/i386/200711080452Z-obj/home/builds/ab/netbsd-4-0-RC4/src/sys/arch/i386/compile/INSTALL_LARGE
total memory = 191 MB
rbus: rbus_min_start set to 0x20000000
avail memory = 178 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
BIOS32 rev. 0 found at 0xfd840
mainbus0 (root)
cpu0 at mainbus0: (uniprocessor)
cpu0: Intel Mobile Pentium II (686-class), 331.85 MHz, id 0x66a
cpu0: features 183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR>
cpu0: features 183f9ff<PGE,MCA,CMOV,PAT,PSE36,MMX>
cpu0: features 183f9ff<FXSR>
cpu0: I-cache 16 KB 32B/line 4-way, D-cache 16 KB 32B/line 4-way
cpu0: L2 cache 256 KB 32B/line 4-way
cpu0: ITLB 32 4 KB entries 4-way, 2 4 MB entries fully associative
cpu0: DTLB 64 4 KB entries 4-way, 8 4 MB entries 4-way
cpu0: 16 page colors
acpi0 at mainbus0: Advanced Configuration and Power Interface
acpi0: using Intel ACPI CA subsystem version 20060217
acpi0: X/RSDT: OemId <PTLTD ,  RSDT  ,06040000>, AslId < LTP,00000000>
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
timecounter: Timecounter "ACPI-Safe" frequency 3579545 Hz quality 900
ACPI-Safe 24-bit timer
LNKA: ACPI: Found matching pin for 0.2.INTA at func 0: 11
LNKB: ACPI: Found matching pin for 0.2.INTB at func 1: 11
LNKA: ACPI: Found matching pin for 0.5.INTA at func 0: 11
LNKD: ACPI: Found matching pin for 0.6.INTD at func 2: 11
LNKC: ACPI: Found matching pin for 0.7.INTA at func 0: 11
ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
ACPI0003 [AC Device] at acpi0 not configured
PNP0C0A [ACPI Control Method Battery] at acpi0 not configured
PNP0C0A [ACPI Control Method Battery] at acpi0 not configured
PNP0C0D [ACPI lid device] at acpi0 not configured
PNP0C0E [ACPI sleep button device] at acpi0 not configured
PNP0A03 [PCI/PCI-X Host Bridge] at acpi0 not configured
PNP0200 [AT DMA Controller] at acpi0 not configured
PNP0001 [EISA Interrupt Controller] at acpi0 not configured
PNP0100 [AT Timer] at acpi0 not configured
PNP0B00 [AT Real-Time Clock] at acpi0 not configured
PNP0800 [AT-style speaker sound] at acpi0 not configured
PNP0C04 [Math Coprocessor] at acpi0 not configured
PNP0C01 [System Board] at acpi0 not configured
PNP0303 [IBM Enhanced (101/102-key, PS/2 mouse support)] at acpi0 not configured
IBM3780 at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0A05 [Generic Container Device] at acpi0 not configured
PNP0A05 [Generic Container Device] at acpi0 not configured
PNP0400 [Standard LPT printer port] at acpi0 not configured
PNP0700 [PC standard floppy disk controller] at acpi0 not configured
PNP0A05 [Generic Container Device] at acpi0 not configured
PNP0C15 at acpi0 not configured
PNP0C02 [Plug and Play motherboard register resources] at acpi0 not configured
PNP0C02 [Plug and Play motherboard register resources] at acpi0 not configured
ACPI Object Type 'Thermal' (0x0d) at acpi0 not configured
ACPI Object Type 'Power' (0x0b) at acpi0 not configured
PNP0C0B [ACPI Fan] at acpi0 not configured
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x8086 product 0x7190 (rev. 0x03)
agp at pchb0 not configured
ppb0 at pci0 dev 1 function 0: vendor 0x8086 product 0x7191 (rev. 0x03)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
vga1 at pci1 dev 0 function 0: vendor 0x10c8 product 0x0005 (rev. 0x20)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
cbb0 at pci0 dev 2 function 0: vendor 0x104c product 0xac1b (rev. 0x03)
cbb1 at pci0 dev 2 function 1: vendor 0x104c product 0xac1b (rev. 0x03)
vendor 0x1013 product 0x6003 (audio multimedia, revision 0x01) at pci0
dev 5 function 0 not configured
pcib0 at pci0 dev 6 function 0
pcib0: vendor 0x8086 product 0x7110 (rev. 0x02)
piixide0 at pci0 dev 6 function 1
piixide0: Intel 82371AB IDE controller (PIIX4) (rev. 0x01)
piixide0: bus-master DMA support present
piixide0: primary channel wired to compatibility mode
piixide0: primary channel interrupting at irq 14
atabus0 at piixide0 channel 0
piixide0: secondary channel wired to compatibility mode
piixide0: secondary channel interrupting at irq 15
atabus1 at piixide0 channel 1
uhci0 at pci0 dev 6 function 2: vendor 0x8086 product 0x7112 (rev. 0x01)
uhci0: interrupting at irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
vendor 0x8086 product 0x7113 (miscellaneous bridge, revision 0x02) at
pci0 dev 6 function 3 not configured
vendor 0x11c1 product 0x0448 (miscellaneous communications, revision
0x01) at pci0 dev 7 function 0 not configured
cbb0: interrupting at irq 11
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 7
pcmcia0 at cardslot0
cbb1: interrupting at irq 11
cardslot1 at cbb1 slot 1 flags 0
cardbus1 at cardslot1: bus 9
pcmcia1 at cardslot1
isa0 at pcib0
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff
npx0: reported by CPUID; using exception 16
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
isapnp0: no ISA Plug 'n Play devices found
timecounter: Timecounter "TSC" frequency 331854680 Hz quality 800
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
Kernelized RAIDframe activated
md0: internal 5000 KB image area
piixide0:0: before reset, st0=0x50, st1=0x50
piixide0:0 drive 1 wd_cyl_lo: got 0x1 != 0x02
piixide0:0 drive 1 wd_sector: got 0x1 != 0x02
piixide0:0 drive 1 wd_cyl_lo(2): got 0x7f != 0x01
piixide0:1: before reset, st0=0x50, st1=0x0
piixide0:1 drive 1 wd_cyl_lo: got 0x0 != 0x02
piixide0:1 drive 1 wd_cyl_lo: got 0x0 != 0x01
piixide0:1 drive 1 wd_cyl_lo(2): got 0x0 != 0x01
piixide0:1:0: after reset, sc=0x1 sn=0x1 cl=0x14 ch=0xeb
piixide0:1:1: after reset, sc=0x0 sn=0x0 cl=0x0 ch=0x0
piixide0:1: wdcwait_reset() end, st0=0x0 st1=0x0
piixide0:1: after reset, ret_value=0x1
piixide0:1:0: after reset, sc=0x1 sn=0x1 cl=0x14 ch=0xeb
piixide0:1: wait DRDY st0 0x0 st1 0x0
atabusattach: ch_drive_flags 0x2 0x0
piixide0:0:0: after reset, sc=0xd0 sn=0xd0 cl=0xd0 ch=0xd0
piixide0:0:1: after reset, sc=0x0 sn=0x0 cl=0x0 ch=0x0
piixide0:0: wdcwait_reset() end, st0=0xd0 st1=0x0
piixide0:0: after reset, ret_value=0x0
atabusattach: ch_drive_flags 0x0 0x0
atapibus0 at atabus1: 2 targets
__wdcwait: timeout (time=11), status d0 error d0 (mask 0x0 bits 0x0)
__wdcwait: timeout (time=11), status d0 error d0 (mask 0x0 bits 0x0)
cd0 at atapibus0 drive 0: <CRN-8241B, 1999/10/15, 1.23> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2
cd0(piixide0:1:0): using PIO mode 4, DMA mode 2 (using DMA)
boot device: <unknown>
root on md0a dumps on md0b
root file system type: ffs
WARNING: clock gained 7 days
WARNING: CHECK AND RESET THE DATE!
warning: no /dev/console
wdc2 at pcmcia0 function 0: <, TWTTI, >
wdc2: i/o mapped mode
atabus2 at wdc2 channel 0
wdc2:0: before reset, st0=0x50, st1=0x0
wdc2:0 drive 1 wd_cyl_lo: got 0x0 != 0x02
wdc2:0 drive 1 wd_cyl_lo: got 0x0 != 0x01
wdc2:0 drive 1 wd_sector: got 0x0 != 0x01
wdc2:0 drive 1 wd_sector: got 0x0 != 0x02
wdc2:0 drive 1 wd_cyl_lo(2): got 0x0 != 0x01
wdc2:0:0: after reset, sc=0x1 sn=0x1 cl=0x0 ch=0x0
wdc2:0:1: after reset, sc=0x0 sn=0x0 cl=0x0 ch=0x0
wdc2:0: wdcwait_reset() end, st0=0x50 st1=0x0
wdc2:0: after reset, ret_value=0x1
wdc2:0:0: after reset, sc=0x1 sn=0x1 cl=0x0 ch=0x0
wdc2:0: wait DRDY st0 0x50 st1 0x0
__wdcwait: timeout (time=11), status 80 error 0 (mask 0x8 bits 0x8)
atabusattach: ch_drive_flags 0x1 0x0
wd0 at atabus2 drive 0: <FCF2GBU>
wd0: drive supports 1-sector PIO transfers, LBA addressing
wd0: 1983 MB, 4029 cyl, 16 head, 63 sec, 512 bytes/sect x 4061232 sectors
wd0: drive supports PIO mode 4