Hi, I have a problem with 4.0BETA2 and also -current.

I can't boot from cd it hangs like on this photo:

http://maciejewski.org/DSC00201.JPG

But I can boot from floppies. After installation there is the same freez.

I tried install some old version (3.99.20) and... everything goes smooth.

I also compiled today 4.0BETA2 on that 3.99.20 and after booting is the
same error.

I think this is not hardware problem due to 3.99.20 works fine.

Any sugesstions?

dmesg:

# dmesg
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004,
2005, 2006
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 3.99.20 (GENERIC) #0: Sat May 27 04:40:33 UTC 2006

riz@b2.netbsd.org:/home/builds/ab/HEAD/i386/200605230000Z-obj/home/builds/ab/HEAD/src/sys/arch/i386/compile/GENERIC
total memory = 1279 MB
avail memory = 1247 MB
BIOS32 rev. 0 found at 0xf0000
mainbus0 (root)
cpu0 at mainbus0: (uniprocessor)
cpu0: Intel Pentium III (686-class), 996.91 MHz, id 0x686
cpu0: features 383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu0: features 383fbff<PGE,MCA,CMOV,PAT,PSE36,MMX>
cpu0: features 383fbff<FXSR,SSE>
cpu0: I-cache 16 KB 32B/line 4-way, D-cache 16 KB 32B/line 4-way
cpu0: L2 cache 256 KB 32B/line 8-way
cpu0: ITLB 32 4 KB entries 4-way, 2 4 MB entries fully associative
cpu0: DTLB 64 4 KB entries 4-way, 8 4 MB entries 4-way
cpu0: 8 page colors
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: ServerWorks CNB20-HE PCI/AGP bridge (rev. 0x06)
pchb1 at pci0 dev 0 function 1
pchb1: ServerWorks CNB20-HE PCI/AGP bridge (rev. 0x06)
pci1 at pchb1 bus 3
pci1: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
cac0 at pci1 dev 3 function 0: Compaq Smart Array 431
cac0: interrupting at irq 5
ld0 at cac0 unit 0: RAID5 array
ld0: 136 GB, 17847 cyl, 255 head, 63 sec, 512 bytes/sect x 286726080 sectors
esiop0 at pci0 dev 1 function 0: Symbios Logic 53c1510d (ultra2-wide scsi)
esiop0: using on-board RAM
esiop0: interrupting at irq 10
scsibus0 at esiop0: 16 targets, 8 luns per target
esiop1 at pci0 dev 1 function 1: Symbios Logic 53c1510d (ultra2-wide scsi)
esiop1: using on-board RAM
esiop1: interrupting at irq 11
scsibus1 at esiop1: 16 targets, 8 luns per target
fxp0 at pci0 dev 2 function 0: i82559 Ethernet, rev 8
fxp0: interrupting at irq 15
fxp0: Ethernet address 00:02:a5:d4:e0:96
inphy0 at fxp0 phy 1: i82555 10/100 media interface, rev. 4
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
vga1 at pci0 dev 3 function 0: ATI Technologies 3D Rage IIC (rev. 0x7a)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
Compaq Advanced Systems Management Controller (miscellaneous system) at
pci0 dev 4 function 0 not configured
ex0 at pci0 dev 5 function 0: 3Com 3c905B-TX 10/100 Ethernet (rev. 0x24)
ex0: interrupting at irq 15
ex0: MAC address 00:01:02:9f:b3:51
exphy0 at ex0 phy 24: 3Com internal media interface
exphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pcib0 at pci0 dev 15 function 0
pcib0: ServerWorks OSB4 southbridge (rev. 0x51)
rccide0 at pci0 dev 15 function 1
rccide0: ServerWorks OSB4 IDE Controller (rev. 0x00)
rccide0: bus-master DMA support present
rccide0: primary channel configured to compatibility mode
rccide0: primary channel interrupting at irq 14
atabus0 at rccide0 channel 0
rccide0: secondary channel configured to compatibility mode
intr_establish: pic pic0 pin 15: can't share type 3 with 2
rccide0: no compatibility interrupt for use by secondary channel
isa0 at pcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
attimer0 at isa0 port 0x40-0x43: AT Timer
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff
npx0: using exception 16
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
pcppi0: attached to attimer0
isapnp0: no ISA Plug 'n Play devices found
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
Kernelized RAIDframe activated
scsibus0: waiting 2 seconds for devices to settle...
scsibus1: waiting 2 seconds for devices to settle...
atapibus0 at atabus0: 2 targets
cd0 at atapibus0 drive 1: <COMPAQ SC-140C, , cq04> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
cd0(rccide0:0:1): using PIO mode 4, DMA mode 2, Ultra-DMA mode 2
(Ultra/33) (using DMA)
boot device: ld0
root on ld0a dumps on ld0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)


-- 
  Bartosz Maciejewski