This system has three 900/100 xeon's with 2M of L2.  The ROM is the "latest"
which comes circa 12/17/2002 of the P20 ROM family.  If my experience is
correct, the chances of this running MP are pretty much nil if I already
have the MP defined in the kernel already.  Right?

buster> dmesg
NetBSD 3.0_STABLE (PETER-FW) #0: Tue May  2 21:46:45 CDT 2006
        
peter@buster:/builds/netbsd-3/i386/obj/builds/netbsd-3/src/sys/arch/i386/com
pile/PETER-FW
total memory = 2047 MB
avail memory = 1995 MB
BIOS32 rev. 0 found at 0xf0000
mainbus0 (root)
cpu0 at mainbus0: (uniprocessor)
cpu0: Intel Pentium III Xeon (686-class), 902.13 MHz, id 0x6a4
cpu0: features 383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR>
cpu0: features 383f9ff<PGE,MCA,CMOV,PAT,PSE36,MMX>
cpu0: features 383f9ff<FXSR,SSE>
cpu0: I-cache 16 KB 32B/line 4-way, D-cache 16 KB 32B/line 4-way
cpu0: L2 cache 2 MB 32B/line 8-way
cpu0: ITLB 32 4 KB entries 4-way, 2 4 MB entries fully associative
cpu0: DTLB 64 4 KB entries 4-way, 8 4 MB entries 4-way
cpu0: 64 page colors
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: ServerWorks CNB20-HE PCI bridge (rev. 0x23)
pchb1 at pci0 dev 0 function 1
pchb1: ServerWorks CNB20-HE PCI bridge (rev. 0x01)
pchb2 at pci0 dev 0 function 2
pchb2: ServerWorks CNB30-LE PCI bridge (rev. 0x01)
pci1 at pchb2 bus 2
pci1: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
Compaq product 0xa0f7 (system subclass 0x04, revision 0x12) at pci1 dev 5
function 0 not configured
cac0 at pci1 dev 6 function 0: Compaq Smart Array 431
cac0: interrupting at irq 10
ld0 at cac0 unit 0: standalone disk or RAID0 array
ld0: 8670 MB, 4403 cyl, 64 head, 63 sec, 512 bytes/sect x 17756160 sectors
ppb0 at pci1 dev 8 function 0: Intel S21152BA,S21154AE/BE PCI-PCI Bridge
(rev. 0x00)
pci2 at ppb0 bus 3
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
fxp0 at pci2 dev 4 function 0: i82559 Ethernet, rev 8
fxp0: interrupting at irq 15
fxp0: Ethernet address 00:08:02:df:11:82
inphy0 at fxp0 phy 1: i82555 10/100 media interface, rev. 4
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp1 at pci2 dev 5 function 0: i82559 Ethernet, rev 8
fxp1: interrupting at irq 15
fxp1: Ethernet address 00:08:02:df:11:83
inphy1 at fxp1 phy 1: i82555 10/100 media interface, rev. 4
inphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pchb3 at pci0 dev 0 function 3
pchb3: ServerWorks CNB30-LE PCI bridge (rev. 0x01)
pci3 at pchb3 bus 7
pci3: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
Compaq product 0xa0f7 (system subclass 0x04, revision 0x12) at pci3 dev 5
function 0 not configured
ahc1 at pci3 dev 6 function 0: Adaptec 29160 Ultra160 SCSI adapter
ahc1: interrupting at irq 5
ahc1: aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
scsibus0 at ahc1: 16 targets, 8 luns per target
ciss0 at pci3 dev 7 function 0: Compaq Smart Array 5300 V1
ciss0: interrupting at irq 3
ciss0: 1 LD, HW rev 0, FW 3.54/3.54
scsibus1 at ciss0: 1 target, 8 luns per target
Compaq Advanced Systems Management Controller (miscellaneous system) at pci0
dev 3 function 0 not configured
esiop0 at pci0 dev 4 function 0: Symbios Logic 53c1510d (ultra2-wide scsi)
esiop0: using on-board RAM
esiop0: interrupting at irq 5
scsibus2 at esiop0: 16 targets, 8 luns per target
esiop1 at pci0 dev 4 function 1: Symbios Logic 53c1510d (ultra2-wide scsi)
esiop1: using on-board RAM
esiop1: interrupting at irq 10
scsibus3 at esiop1: 16 targets, 8 luns per target
vga1 at pci0 dev 5 function 0: ATI Technologies 3D Rage IIC (rev. 0x7a)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
pcib0 at pci0 dev 15 function 0
pcib0: ServerWorks OSB4 southbridge (rev. 0x51)
rccide0 at pci0 dev 15 function 1
rccide0: ServerWorks OSB4 IDE Controller (rev. 0x00)
rccide0: bus-master DMA support present
rccide0: primary channel configured to compatibility mode
rccide0: primary channel interrupting at irq 14
atabus0 at rccide0 channel 0
rccide0: secondary channel configured to compatibility mode
intr_establish: pic pic0 pin 15: can't share type 3 with 2
rccide0: no compatibility interrupt for use by secondary channel
isa0 at pcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff: using exception 16
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
isapnp0: no ISA Plug 'n Play devices found
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
Kernelized RAIDframe activated
IPsec: Initialized Security Association Processing.
scsibus0: waiting 2 seconds for devices to settle...
scsibus1: waiting 2 seconds for devices to settle...
scsibus2: waiting 2 seconds for devices to settle...
scsibus3: waiting 2 seconds for devices to settle...
sd0 at scsibus0 target 0 lun 0: <IFT, 3102, 0212> disk fixed
sd0: 61010 MB, 61010 cyl, 64 head, 32 sec, 512 bytes/sect x 124948992
sectors
sd0: sync (50.00ns offset 16), 16-bit (40.000MB/s) transfers, tagged
queueing
atapibus0 at atabus0: 2 targets
cd0 at atapibus0 drive 0: <Compaq  CRD-8402B, 2000/05/10, 1.03> cdrom
removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2
cd0(rccide0:0:0): using PIO mode 4, DMA mode 2 (using DMA)
sd1 at scsibus1 target 0 lun 0: <COMPAQ, LOGICAL VOLUME, 3.54> disk fixed
sd1: 69463 MB, 17434 cyl, 255 head, 32 sec, 512 bytes/sect x 142261440
sectors
boot device: ld0
root on ld0a dumps on ld0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
buster>