Hi!

I am trying to get an iAudio 5 (mp3player) to work with my IBM
Thinkpad X40 running NetBSD-CURRENT as of May 5 2005. When I plugin
the device I get the following in my dmesg

umass0 at uhub3 port 4 configuration 1 interface 0
umass0: COWON iAUDIO 5, rev 2.00/1.10, addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 1 lun per target
sd0 at scsibus0 target 0 lun 0: <COWON, iAUDIO 5, 0100> disk removable
sd0: fabricating a geometry
sd0: 993 MB, 993 cyl, 64 head, 32 sec, 512 bytes/sect x 2035200 sectors

And the disklabel for sd0 looks like this

# /dev/rsd0d:
type: SCSI
disk: mydisk
label: fictitious
flags: removable
bytes/sector: 512
sectors/track: 32
tracks/cylinder: 64
sectors/cylinder: 2048
cylinders: 993
total sectors: 2035200
rpm: 3600
interleave: 1
trackskew: 0
cylinderskew: 0
headswitch: 0           # microseconds
track-to-track seek: 0  # microseconds
drivedata: 0 

5 partitions:
#        size    offset     fstype [fsize bsize cpg/sgs]
 d:   2035200         0     unused      0     0        # (Cyl.      0 -    993*)
 e:   2035147        53      MSDOS                     # (Cyl.      0*-    993*)
disklabel: boot block size 0
disklabel: super block size 0

But when I try to mount (mount /dev/sd0e /mnt) it gives me this error message

mount_msdos: /dev/sd0e on /mnt: Invalid argument

and in this appears in my dmesg

sd0: fabricating a geometry
sd0: fabricating a geometry

Should I try to make a new disklabel and newfs it? I have tried with a
newer kernel from netbsd-3 branch (20050812) with the same result. I
havent any other USB device so I cant check that the USB controller is
working correctly.

Regards,
Claes Leufven


Here is my dmesg output for the IBM X40

NetBSD 2.99.11 (EIN) #0: Thu May  5 11:33:23 CEST 2005
	root@ein.outherlimits.org:/usr/src/sys/arch/i386/compile/EIN
total memory = 502 MB
avail memory = 488 MB
BIOS32 rev. 0 found at 0xfd740
PCI BIOS rev. 2.1 found at 0xfd8c8
PCI IRQ Routing Table rev. 1.0 found at 0xfdeb0, size 256 bytes (14 entries)
PCI Interrupt Router at 000:31:0 (vendor 0x8086 product 0x122e compatible)
mainbus0 (root)
cpu0 at mainbus0: (uniprocessor)
cpu0: Intel Pentium M (Banias) (686-class), 1196.16 MHz, id 0x695
cpu0: features a7e9fbbf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,APIC,SEP,MTRR>
cpu0: features a7e9fbbf<PGE,MCA,CMOV,PAT,CFLUSH,DS,ACPI,MMX>
cpu0: features a7e9fbbf<FXSR,SSE,SSE2,TM,SBF>
cpu0: features2 180<EST,TM2>
cpu0: "Intel(R) Pentium(R) M processor 1200MHz"
cpu0: using thermal monitor 2
cpu0: Enhanced SpeedStep running at 1200 MHz (1180 mV)
cpu0: Enhanced SpeedStep frequencies available (MHz): 1200 1100 1000 900 800 600
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x8086 product 0x3580 (rev. 0x02)
agp0 at pchb0: detected 8060k stolen memory
agp0: aperture at 0xe0000000, size 0x8000000
vendor 0x8086 product 0x3584 (miscellaneous system, revision 0x02) at pci0 dev 0 function 1 not configured
vendor 0x8086 product 0x3585 (miscellaneous system, revision 0x02) at pci0 dev 0 function 3 not configured
vga0 at pci0 dev 2 function 0: vendor 0x8086 product 0x3582 (rev. 0x02)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
vendor 0x8086 product 0x3582 (miscellaneous display, revision 0x02) at pci0 dev 2 function 1 not configured
uhci0 at pci0 dev 29 function 0: vendor 0x8086 product 0x24c2 (rev. 0x01)
uhci0: interrupting at irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 29 function 1: vendor 0x8086 product 0x24c4 (rev. 0x01)
uhci1: interrupting at irq 11
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2 at pci0 dev 29 function 2: vendor 0x8086 product 0x24c7 (rev. 0x01)
uhci2: interrupting at irq 11
usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
ehci0 at pci0 dev 29 function 7: vendor 0x8086 product 0x24cd (rev. 0x01)
ehci0: interrupting at irq 11
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2
usb3 at ehci0: USB revision 2.0
uhub3 at usb3
uhub3: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: single transaction translator
uhub3: 6 ports with 6 removable, self powered
ppb0 at pci0 dev 30 function 0: vendor 0x8086 product 0x2448 (rev. 0x81)
pci1 at ppb0 bus 2
pci1: i/o space, memory space enabled
cbb0 at pci1 dev 0 function 0: vendor 0x1180 product 0x0476 (rev. 0x8d)
vendor 0x1180 product 0x0822 (system subclass 0x05, revision 0x13) at pci1 dev 0 function 1 not configured
wm0 at pci1 dev 1 function 0: Intel i82541GI Mobile 1000BASE-T Ethernet, rev. 0
wm0: interrupting at irq 11
wm0: 32-bit 33MHz PCI bus
wm0: 64 word (6 address bits) MicroWire EEPROM
wm0: Ethernet address 00:0a:e4:33:04:59
igphy0 at wm0 phy 1: Intel IGP01E1000 Gigabit PHY, rev. 0
wm0: MDIC write timed out: phy 1 reg 31
wm0: MDIC write timed out: phy 1 reg 0
igphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
ipw0 at pci1 dev 2 function 0: vendor 0x8086 product 0x1043 (rev. 0x04)
ipw0: interrupting at irq 11
ipw0: 802.11 address 00:0c:f1:53:78:21
ipw0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
cbb0: interrupting at irq 11
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 3 device 0
pcmcia0 at cardslot0
pcib0 at pci0 dev 31 function 0
pcib0: vendor 0x8086 product 0x24cc (rev. 0x01)
piixide0 at pci0 dev 31 function 1
piixide0: Intel 82801DBM IDE Controller (ICH4-M) (rev. 0x01)
piixide0: bus-master DMA support present
piixide0: primary channel wired to compatibility mode
piixide0: primary channel interrupting at irq 14
atabus0 at piixide0 channel 0
piixide0: secondary channel wired to compatibility mode
piixide0: secondary channel interrupting at irq 15
atabus1 at piixide0 channel 1
vendor 0x8086 product 0x24c3 (SMBus serial bus, revision 0x01) at pci0 dev 31 function 3 not configured
auich0 at pci0 dev 31 function 5: i82801DB/DBM (ICH4/ICH4M) AC-97 Audio
auich0: interrupting at irq 11
auich0: ac97: Analog Devices AD1981B codec; headphone, 20 bit DAC, no 3D stereo
auich0: ac97: ext id 601<AC97_22,AMAP,VRA>
vendor 0x8086 product 0x24c6 (modem communications, revision 0x01) at pci0 dev 31 function 6 not configured
isa0 at pcib0
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff: using exception 16
isapnp0: no ISA Plug 'n Play devices found
apm0 at mainbus0: Power Management spec V1.2
auich0: measured ac97 link rate at 48003 Hz, will use 48000 Hz
audio0 at auich0: full duplex, mmap, independent
IPsec: Initialized Security Association Processing.
wd0 at atabus0 drive 0: <HITACHI_DK13FA-40B>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 38154 MB, 77520 cyl, 16 head, 63 sec, 512 bytes/sect x 78140160 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
Accounting started
piixide0:0:0: lost interrupt
	type: ata tc_bcount: 0 tc_skip: 0
arplookup: unable to enter address for 10.0.0.1@00:08:02:a1:aa:e2 on ipw0 (host is not on local network)
umass0 at uhub3 port 4 configuration 1 interface 0
umass0: COWON iAUDIO 5, rev 2.00/1.10, addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 1 lun per target
sd0 at scsibus0 target 0 lun 0: <COWON, iAUDIO 5, 0100> disk removable
sd0: fabricating a geometry
sd0: 993 MB, 993 cyl, 64 head, 32 sec, 512 bytes/sect x 2035200 sectors
sd0: fabricating a geometry
sd0: fabricating a geometry
sd0: fabricating a geometry
umass0: at uhub3 port 4 (addr 2) disconnected
sd0 detached
scsibus0 detached
umass0 detached
umass0 at uhub3 port 4 configuration 1 interface 0
umass0: COWON iAUDIO 5, rev 2.00/1.10, addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 1 lun per target
sd0 at scsibus0 target 0 lun 0: <COWON, iAUDIO 5, 0100> disk removable
sd0: fabricating a geometry
sd0: 993 MB, 993 cyl, 64 head, 32 sec, 512 bytes/sect x 2035200 sectors
sd0: fabricating a geometry
ipw0: could not map header DMA memory (error 27)
ipw0: could not map header DMA memory (error 27)
sd0: fabricating a geometry
sd0: fabricating a geometry