--XsQoSWH+UP9D9v3l
Content-Type: text/plain; charset=us-ascii
Content-Disposition: inline

Hello,

my laptop has an Intel 82371AB USB Host Controller which gets irq
128 assigned.
The Interrupt Router Intel 82371FB PCI-to-ISA Bridge (PIIX) issues a
warning:

000:07:2 0x8086 0x7112   D  0x03   5  2    WARNING: preserving irq 128

Is it possible to configure a reasonable irq for this device?

-Hanspeter


--XsQoSWH+UP9D9v3l
Content-Type: text/plain; charset=us-ascii
Content-Disposition: attachment; filename="dmesg.boot"

NetBSD 1.6.1 (GENERIC_LAPTOP) #0: Tue Apr  8 12:21:37 UTC 2003
    autobuild@tgm.daemon.org:/autobuild/netbsd-1-6/i386/OBJ/autobuild/netbsd-1-6/src/sys/arch/i386/compile/GENERIC_LAPTOP
cpu0: Intel Pentium III (Coppermine) Celeron (686-class), 630.50 MHz
cpu0: I-cache 16 KB 32b/line 4-way, D-cache 16 KB 32b/line 2-way
cpu0: L2 cache 128 KB 32b/line 4-way
cpu0: features 383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR>
cpu0: features 383f9ff<PGE,MCA,CMOV,FGPAT,PSE36,MMX>
cpu0: features 383f9ff<FXSR,SSE>
total memory = 127 MB
avail memory = 113 MB
using 1658 buffers containing 6632 KB of memory
RTC BIOS diagnostic error 20<config_unit>
BIOS32 rev. 0 found at 0xeb240
PCI BIOS rev. 2.1 found at 0xeb280
pcibios: config mechanism [1][x], special cycles [1][x], last bus 1
PCI IRQ Routing Table rev. 1.0 found at 0xfe840, size 112 bytes (5 entries)
PCI Interrupt Router at 000:07:0 (Intel 82371FB PCI-to-ISA Bridge (PIIX))
------------------------------------------
  device vendor product pin PIRQ IRQ stage
------------------------------------------
000:07:2 0x8086 0x7112   D  0x03   5  2    WARNING: preserving irq 128
000:08:0 0x104c 0xac1c   A  0x00  10  0    already assigned
000:08:1 0x104c 0xac1c   A  0x00  10  0    already assigned
000:09:0 0x1013 0x6003   A  0x02   5  0    already assigned
000:10:0 0x11c1 0x044a   A  0x01   5  0    already assigned
001:00:0 0x1002 0x4c42   A  0x00  10  0    fixed up
------------------------------------------
PCI fixup examining 8086:7190
PCI fixup examining 8086:7191
PCI fixup examining 1002:4c42
PCI bridge 0: primary 0, secondary 1, subordinate 1
PCI fixup examining 8086:7110
PCI fixup examining 8086:7111
PCI fixup examining 8086:7112
PCI fixup examining 8086:7113
PCI fixup examining 104c:ac1c
PCI bridge 1: primary 0, secondary 2, subordinate 2
PCI fixup examining 104c:ac1c
PCI bridge 2: primary 0, secondary 3, subordinate 3
PCI fixup examining 1013:6003
PCI fixup examining 11c1:44a
PCI bus #3 is the last bus
[System BIOS Setting]-----------------------
  device vendor product
  register space address    size
--------------------------------------------
000:00:0 0x8086 0x7190 
	10h mem  0x20000000 0x10000000
		[OK]
000:01:0 0x8086 0x7191 
		[OK]
000:07:0 0x8086 0x7110 
		[OK]
000:07:1 0x8086 0x7111 
	20h port 0x00001100 0x00000010
		[OK]
000:07:2 0x8086 0x7112 
	20h port 0x00001200 0x00000020
		[OK]
000:07:3 0x8086 0x7113 
		[OK]
000:08:0 0x104c 0xac1c 
	10h mem  0x08000000 0x00001000
		[OK]
000:08:1 0x104c 0xac1c 
	10h mem  0x08001000 0x00001000
		[OK]
000:09:0 0x1013 0x6003 
	10h mem  0xe8000000 0x00001000
	14h mem  0xe9000000 0x00100000
		[OK]
000:10:0 0x11c1 0x044a 
	10h mem  0xe9100000 0x00000100
	14h port 0x00001060 0x00000008
	18h port 0x00001800 0x00000100
		[OK]
001:00:0 0x1002 0x4c42 
	10h mem  0xe4000000 0x01000000
	14h port 0x0000d000 0x00000100
	18h mem  0xe6000000 0x00001000
		[OK]
--------------------------[  0 devices bogus]
 Physical memory end: 0x07fee000
 PCI memory mapped I/O space start: 0x08000000
mainbus0 (root)
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: Intel 82443BX Host Bridge/Controller (rev. 0x03)
agp0 at pchb0: aperture at 0x20000000, size 0x8000000
ppb0 at pci0 dev 1 function 0: Intel 82443BX AGP Interface (rev. 0x03)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
vga1 at pci1 dev 0 function 0: ATI Technologies 3D Rage LT Pro (AGP) (rev. 0xdc)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
pcib0 at pci0 dev 7 function 0
pcib0: Intel 82371AB PCI-to-ISA Bridge (PIIX4) (rev. 0x02)
pciide0 at pci0 dev 7 function 1: Intel 82371AB IDE controller (PIIX4) (rev. 0x01)
pciide0: bus-master DMA support present
pciide0: primary channel wired to compatibility mode
wd0 at pciide0 channel 0 drive 0: <FUJITSU MHN2200AT>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 19077 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 39070080 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
pciide0: primary channel interrupting at irq 14
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA data transfers)
pciide0: secondary channel wired to compatibility mode
atapibus0 at pciide0 channel 1: 2 targets
cd0 at atapibus0 drive 0: <CD-224E, , 1.5A> type 5 cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2
pciide0: secondary channel interrupting at irq 15
cd0(pciide0:1:0): using PIO mode 4, DMA mode 2 (using DMA data transfers)
uhci0 at pci0 dev 7 function 2: Intel 82371AB USB Host Controller (PIIX4) (rev. 0x01)
pci_intr_map: bad interrupt line 128
uhci0: couldn't map interrupt
Intel 82371AB Power Management Controller (PIIX4) (miscellaneous bridge, revision 0x02) at pci0 dev 7 function 3 not configured
cbb0 at pci0 dev 8 function 0: Texas Instruments PCI1225 PCI-CardBus Bridge (rev. 0x01)
cbb1 at pci0 dev 8 function 1: Texas Instruments PCI1225 PCI-CardBus Bridge (rev. 0x01)
clcs0 at pci0 dev 9 function 0: Cirrus Logic CS4280 CrystalClear Audio Interface (rev. 0x01)
clcs0: interrupting at irq 5
clcs0: Crystal CS4297 codec; headphone, 18 bit DAC, 18 bit ADC, no 3D stereo
audio0 at clcs0: full duplex, independent
midi0 at clcs0: CS4280 MIDI UART
Lucent Technologies LTMODEM (miscellaneous communications, revision 0x01) at pci0 dev 10 function 0 not configured
isa0 at pcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
lpt0 at isa0 port 0x378-0x37b irq 7
pcppi0 at isa0 port 0x61
midi1 at pcppi0: PC speaker
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff: using exception 16
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
isapnp0: no ISA Plug 'n Play devices found
cbb0: interrupting at irq 10
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 2 device 0
pcmcia0 at cardslot0
cbb1: interrupting at irq 10
cardslot1 at cbb1 slot 1 flags 0
cardbus1 at cardslot1: bus 3 device 0
pcmcia1 at cardslot1
apm0 at mainbus0: Power Management spec V1.2
biomask ef45 netmask ef45 ttymask ffc7
ne0 at pcmcia1 function 0
ne0: SVEC PN650TX 10/100 Dual Speed Fast Ethernet PC Card (DL10022) Ethernet
ne0: Ethernet address 00:e0:98:77:6c:ba
ukphy0 at ne0 phy 4: Generic IEEE 802.3u media interface
ukphy0: OUI 0x0008bb, model 0x0001, rev. 2
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
IP Filter: v3.4.29 initialized.  Default = pass all, Logging = enabled
duplicate IP address 192.168.2.1 sent from link address 00:00:e8:63:09:f3
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
wsdisplay0: screen 5 added (80x25, vt100 emulation)
wsdisplay0: screen 6 added (80x25, vt100 emulation)

--XsQoSWH+UP9D9v3l--