Subject: Re: built-in wi on sony vaio
To: None <port-i386@netbsd.org>
From: Manuel Bouyer <bouyer@antioche.eu.org>
List: port-i386
Date: 04/08/2003 23:09:01
--wRRV7LY7NUeQGEoC
Content-Type: text/plain; charset=us-ascii
Content-Disposition: inline
On Wed, Mar 26, 2003 at 04:48:55PM +0100, Lennart Augustsson wrote:
> Have you tried ACPI?
For fun I tried a current ACPI kernel (all acpi stuff enabled).
With this kernel the mouse doesn't work any more, it doesn't get an
interrupt.
>
> -- Lennart
>
> Manuel Bouyer wrote:
>
> >Hi,
> >I tried to get the build-in wireless interface on a sony vaio (model
> >PGC-R600HMDP) to work, without success. The bios doens't assign it an
> >interrupt, and the various pcibios options fails to allocate one too.
> >Attached is the message boot (from a 1.6.1_RC2 kernel with intel 830MP
> >support
> >pulled up; I tried a current kernel with the same result).
> >It looks like the device doens't even appear in the messages from
> >PCIBIOS interrupt routines (but it appears in the IO/Mem PCIBIOS table).
> >Any idea ?
> >
> >--
> >Manuel Bouyer, LIP6, Universite Paris VI. Manuel.Bouyer@lip6.fr
> > NetBSD: 24 ans d'experience feront toujours la difference
> >--
> >
> >
> >------------------------------------------------------------------------
> >
> >NetBSD 1.6.1_RC2 (GENRIC-manu) #3: Tue Mar 25 18:44:09 CET 2003
> > bouyer@pop:/local/pop1/bouyer/netbsd-1-6/src/sys/arch/i386/compile/GENRIC-manu
> >cpu0: Intel Pentium III (Tualatin) (686-class), 1193.17 MHz
> >cpu0: I-cache 16 KB 32b/line 4-way, D-cache 16 KB 32b/line 2-way
> >cpu0: L2 cache 512 KB 32b/line 8-way
> >cpu0: features 383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR>
> >cpu0: features 383f9ff<PGE,MCA,CMOV,FGPAT,PSE36,MMX>
> >cpu0: features 383f9ff<FXSR,SSE>
> >total memory = 254 MB
> >avail memory = 229 MB
> >using 3277 buffers containing 13108 KB of memory
> >BIOS32 rev. 0 found at 0xfd871
> >PCI BIOS rev. 2.1 found at 0xfd9aa
> >pcibios: config mechanism [1][x], special cycles [x][x], last bus 2
> >PCI IRQ Routing Table rev. 1.0 found at 0xfdf30, size 176 bytes (9 entries)
> >PCI Interrupt Router at 000:31:0 (Intel 82371FB PCI-to-ISA Bridge (PIIX))
> >PIR Entry 0:
> > Bus: 0 Device: 30
> > INTA: link 0x00 bitmap 0xdef8
> > INTB: link 0x00 bitmap 0xdef8
> > INTC: link 0x00 bitmap 0xdef8
> > INTD: link 0x00 bitmap 0xdef8
> >PIR Entry 1:
> > Bus: 2 Device: 2
> > INTA: link 0x00 bitmap 0xdef8
> > INTB: link 0x00 bitmap 0xdef8
> > INTC: link 0x00 bitmap 0xdef8
> > INTD: link 0x00 bitmap 0xdef8
> >PIR Entry 2:
> > Bus: 2 Device: 5
> > INTA: link 0x69 bitmap 0x0008
> > INTB: link 0x00 bitmap 0xdef8
> > INTC: link 0x00 bitmap 0xdef8
> > INTD: link 0x00 bitmap 0xdef8
> >PIR Entry 3:
> > Bus: 2 Device: 8
> > INTA: link 0x68 bitmap 0x0200
> > INTB: link 0x00 bitmap 0xdef8
> > INTC: link 0x00 bitmap 0xdef8
> > INTD: link 0x00 bitmap 0xdef8
> >PIR Entry 4:
> > Bus: 0 Device: 0
> > INTA: link 0x00 bitmap 0xdef8
> > INTB: link 0x00 bitmap 0xdef8
> > INTC: link 0x00 bitmap 0xdef8
> > INTD: link 0x00 bitmap 0xdef8
> >PIR Entry 5:
> > Bus: 0 Device: 31
> > INTA: link 0x00 bitmap 0xdef8
> > INTB: link 0x00 bitmap 0xdef8
> > INTC: link 0x00 bitmap 0xdef8
> > INTD: link 0x00 bitmap 0xdef8
> >PIR Entry 6:
> > Bus: 0 Device: 29
> > INTA: link 0x60 bitmap 0x0200
> > INTB: link 0x63 bitmap 0x0200
> > INTC: link 0x00 bitmap 0xdef8
> > INTD: link 0x00 bitmap 0xdef8
> >PIR Entry 7:
> > Bus: 0 Device: 2
> > INTA: link 0x60 bitmap 0x0200
> > INTB: link 0x00 bitmap 0xdef8
> > INTC: link 0x00 bitmap 0xdef8
> > INTD: link 0x00 bitmap 0xdef8
> >PIR Entry 8:
> > Bus: 0 Device: 1
> > INTA: link 0x60 bitmap 0x0200
> > INTB: link 0x00 bitmap 0xdef8
> > INTC: link 0x00 bitmap 0xdef8
> > INTD: link 0x00 bitmap 0xdef8
> >pciintr_link_fixup: PIRQ 0x00 already connected to IRQ 9
> >pciintr_link_fixup: PIRQ 0x03 already connected to IRQ 9
> >pciintr_link_route: route of PIRQ 0x00 -> IRQ 9 preserved BIOS setting
> >pciintr_link_route: route of PIRQ 0x03 -> IRQ 9 preserved BIOS setting
> >------------------------------------------
> > device vendor product pin PIRQ IRQ stage
> >------------------------------------------
> >000:02:0 0x8086 0x3577 A 0x00 9 0 already assigned
> >000:29:0 0x8086 0x2482 A 0x00 9 0 already assigned
> >000:29:1 0x8086 0x2484 B 0x03 9 0 already assigned
> >pciintr_header_fixup: no entry for link 0x69 (2:5:0:A)
> >pciintr_header_fixup: no entry for link 0x68 (2:8:0:A)
> >------------------------------------------
> >PCI fixup examining 8086:3575
> >PCI fixup examining 8086:3577
> >PCI fixup examining 8086:3577
> >PCI fixup examining 8086:2482
> >PCI fixup examining 8086:2484
> >PCI fixup examining 8086:2487
> >PCI fixup examining 8086:2448
> >PCI fixup examining 104c:8023
> >PCI fixup examining 1180:475
> >PCI bridge 1: primary 1, secondary 2, subordinate 2
> >PCI fixup examining 8086:1031
> >PCI fixup examining 1260:3873
> >PCI bridge 0: primary 0, secondary 1, subordinate 2
> >PCI fixup examining 8086:248c
> >PCI fixup examining 8086:248a
> >PCI fixup examining 8086:2483
> >PCI fixup examining 8086:2485
> >PCI fixup examining 8086:2486
> >PCI bus #2 is the last bus
> >[System BIOS Setting]-----------------------
> > device vendor product
> > register space address size
> >--------------------------------------------
> >000:00:0 0x8086 0x3575
> > [OK]
> >000:02:0 0x8086 0x3577
> > 10h mem 0xe8000000 0x08000000
> > 14h mem 0xe0000000 0x00080000
> > [OK]
> >000:02:1 0x8086 0x3577
> > 10h mem 0xf0000000 0x08000000
> > 14h mem 0xe0080000 0x00080000
> > [OK]
> >000:29:0 0x8086 0x2482
> > 20h port 0x00001800 0x00000020
> > [OK]
> >000:29:1 0x8086 0x2484
> > 20h port 0x00001820 0x00000020
> > [OK]
> >000:29:2 0x8086 0x2487
> > 20h port 0x00001840 0x00000020
> > [OK]
> >000:30:0 0x8086 0x2448
> > [OK]
> >000:31:0 0x8086 0x248c
> > [OK]
> >000:31:1 0x8086 0x248a
> > 10h port 0x000001f0 0x00000008
> > 14h port 0x000003f4 0x00000004
> > 18h port 0x00000170 0x00000008
> > 1ch port 0x00000374 0x00000004
> > 20h port 0x00001860 0x00000010
> > 24h mem 0xe0100000 0x00000400
> > [OK]
> >000:31:3 0x8086 0x2483
> > 20h port 0x00001880 0x00000020
> > [OK]
> >000:31:5 0x8086 0x2485
> > 10h port 0x00001c00 0x00000100
> > 14h port 0x000018c0 0x00000040
> > [OK]
> >000:31:6 0x8086 0x2486
> > 10h port 0x00002400 0x00000100
> > 14h port 0x00002000 0x00000080
> > [OK]
> >001:02:0 0x104c 0x8023
> > 10h mem 0xe0205000 0x00000800
> > 14h mem 0xe0200000 0x00004000
> > [OK]
> >001:05:0 0x1180 0x0475
> > 10h mem 0x00000000 0x00001000
> > [NG]
> >001:08:0 0x8086 0x1031
> > 10h mem 0xe0204000 0x00001000
> > 14h port 0x00003000 0x00000040
> > [OK]
> >001:11:0 0x1260 0x3873
> > 10h mem 0xe0500000 0x00001000
> > [OK]
> >--------------------------[ 1 devices bogus]
> >Physical memory end: 0x0fe7c000
> >PCI memory mapped I/O space start: 0x0ff00000
> >[PCIBIOS fixup stage]-----------------------
> > device vendor product
> > register space address size
> >--------------------------------------------
> >000:00:0 0x8086 0x3575
> > [OK]
> >000:02:0 0x8086 0x3577
> > 10h mem 0xe8000000 0x08000000
> > 14h mem 0xe0000000 0x00080000
> > [OK]
> >000:02:1 0x8086 0x3577
> > 10h mem 0xf0000000 0x08000000
> > 14h mem 0xe0080000 0x00080000
> > [OK]
> >000:29:0 0x8086 0x2482
> > 20h port 0x00001800 0x00000020
> > [OK]
> >000:29:1 0x8086 0x2484
> > 20h port 0x00001820 0x00000020
> > [OK]
> >000:29:2 0x8086 0x2487
> > 20h port 0x00001840 0x00000020
> > [OK]
> >000:30:0 0x8086 0x2448
> > [OK]
> >000:31:0 0x8086 0x248c
> > [OK]
> >000:31:1 0x8086 0x248a
> > 10h port 0x000001f0 0x00000008
> > 14h port 0x000003f4 0x00000004
> > 18h port 0x00000170 0x00000008
> > 1ch port 0x00000374 0x00000004
> > 20h port 0x00001860 0x00000010
> > 24h mem 0xe0100000 0x00000400
> > [OK]
> >000:31:3 0x8086 0x2483
> > 20h port 0x00001880 0x00000020
> > [OK]
> >000:31:5 0x8086 0x2485
> > 10h port 0x00001c00 0x00000100
> > 14h port 0x000018c0 0x00000040
> > [OK]
> >000:31:6 0x8086 0x2486
> > 10h port 0x00002400 0x00000100
> > 14h port 0x00002000 0x00000080
> > [OK]
> >001:02:0 0x104c 0x8023
> > 10h mem 0xe0205000 0x00000800
> > 14h mem 0xe0200000 0x00004000
> > [OK]
> >001:05:0 0x1180 0x0475
> > 10h mem 0x0ff00000 0x00001000
> > [OK]
> >001:08:0 0x8086 0x1031
> > 10h mem 0xe0204000 0x00001000
> > 14h port 0x00003000 0x00000040
> > [OK]
> >001:11:0 0x1260 0x3873
> > 10h mem 0xe0500000 0x00001000
> > [OK]
> >--------------------------[ 0 devices bogus]
> >mainbus0 (root)
> >pci0 at mainbus0 bus 0: configuration mode 1
> >pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
> >pchb0 at pci0 dev 0 function 0
> >pchb0: Intel 82830MP CPU to I/O Bridge 1 (rev. 0x04)
> >agp0 at pchb0: aperture at 0x0, size 0x8000000
> >vga1 at pci0 dev 2 function 0: Intel 82830MP Integrated Video (rev. 0x04)
> >wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
> >wsmux1: connecting to wsdisplay0
> >Intel 82830MP Integrated Video (miscellaneous display) at pci0 dev 2
> >function 1 not configured
> >uhci0 at pci0 dev 29 function 0: Intel 82801CA/CAM USB Controller (rev.
> >0x02)
> >uhci0: interrupting at irq 9
> >usb0 at uhci0: USB revision 1.0
> >uhub0 at usb0
> >uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> >uhub0: 2 ports with 2 removable, self powered
> >uhci1 at pci0 dev 29 function 1: Intel 82801CA/CAM USB Controller (rev.
> >0x02)
> >uhci1: interrupting at irq 9
> >usb1 at uhci1: USB revision 1.0
> >uhub1 at usb1
> >uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> >uhub1: 2 ports with 2 removable, self powered
> >uhci2 at pci0 dev 29 function 2: Intel 82801CA/CAM USB Controller (rev.
> >0x02)
> >pci_intr_map: no mapping for pin C (line=ff)
> >uhci2: couldn't map interrupt
> >ppb0 at pci0 dev 30 function 0: Intel 82801BAM Hub-to-PCI Bridge (rev.
> >0x42)
> >pci1 at ppb0 bus 1
> >pci1: i/o space, memory space enabled
> >Texas Instruments product 0x8023 (Firewire serial bus, interface 0x10) at
> >pci1 dev 2 function 0 not configured
> >Ricoh 5C475 PCI-CardBus bridge (CardBus bridge, revision 0x80) at pci1 dev
> >5 function 0 not configured
> >fxp0 at pci1 dev 8 function 0: Intel PRO/100 VE Network Controller, rev 66
> >fxp0: interrupting at irq 9
> >fxp0: Ethernet address 08:00:46:77:e9:af
> >ukphy0 at fxp0 phy 1: Generic IEEE 802.3u media interface
> >ukphy0: i82562ET 10/100 media interface (OUI 0x005500, model 0x0033), rev.
> >0
> >ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> >wi0 at pci1 dev 11 function 0: Intersil Prism2.5 Wireless Lan
> >pci_intr_map: no mapping for pin D (line=ff)
> >wi0: couldn't map interrupt
> >pcib0 at pci0 dev 31 function 0
> >pcib0: Intel 82801CAM LPC Interface (rev. 0x02)
> >pciide0 at pci0 dev 31 function 1: Intel 82801CA IDE Controller (rev. 0x02)
> >pciide0: bus-master DMA support present
> >pciide0: primary channel wired to compatibility mode
> >wd0 at pciide0 channel 0 drive 0: <IC25N040ATCS04-0>
> >wd0: drive supports 16-sector PIO transfers, LBA addressing
> >wd0: 38154 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 78140160
> >sectors
> >wd0: 32-bit data port
> >wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
> >pciide0: primary channel interrupting at irq 14
> >wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using
> >DMA data transfers)
> >pciide0: secondary channel wired to compatibility mode
> >pciide0: disabling secondary channel (no drives)
> >Intel 82801CA/CAM SMBus Controller (SMBus serial bus, revision 0x02) at
> >pci0 dev 31 function 3 not configured
> >auich0 at pci0 dev 31 function 5: i82801CA AC-97 Audio
> >auich0: interrupting at irq 9
> >auich0: YMH3 codec; 18 bit DAC, no 3D stereo
> >auich0: warning, fixed rate codec
> >audio0 at auich0: full duplex, mmap, independent
> >Intel 82801CA/CAM Modem (modem communications, revision 0x02) at pci0 dev
> >31 function 6 not configured
> >isa0 at pcib0
> >com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
> >pckbc0 at isa0 port 0x60-0x64
> >pckbd0 at pckbc0 (kbd slot)
> >pckbc0: using irq 1 for kbd slot
> >wskbd0 at pckbd0: console keyboard, using wsdisplay0
> >pms0 at pckbc0 (aux slot)
> >pckbc0: using irq 12 for aux slot
> >wsmouse0 at pms0 mux 0
> >lpt0 at isa0 port 0x378-0x37b irq 7
> >pcppi0 at isa0 port 0x61
> >midi0 at pcppi0: PC speaker
> >sysbeep0 at pcppi0
> >isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
> >npx0 at isa0 port 0xf0-0xff: using exception 16
> >fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
> >pcic0 at isa0 port 0x3e0-0x3e1 iomem 0xd0000-0xdffff irq
> >pcic0: controller 0 (Intel 82365SL Revision 1) has socket A only
> >pcic0: controller 1 (Intel 82365SL Revision 1) has no sockets
> >pcmcia0 at pcic0 controller 0 socket 0
> >isapnp0: no ISA Plug 'n Play devices found
> >biomask ef6d netmask ef6d ttymask ffef
> >pcic0: controller 0 detecting irqs with mask 0xdeb8: none
> >pcic0: no available irq; polling for socket events
> >Kernelized RAIDframe activated
> >boot device: wd0
> >root on wd0a dumps on wd0b
> >root file system type: ffs
> >wsdisplay0: screen 1 added (80x25, vt100 emulation)
> >wsdisplay0: screen 2 added (80x25, vt100 emulation)
> >wsdisplay0: screen 3 added (80x25, vt100 emulation)
> >wsdisplay0: screen 4 added (80x25, vt100 emulation)
> >
> >
>
--
Manuel Bouyer <bouyer@antioche.eu.org>
NetBSD: 24 ans d'experience feront toujours la difference
--
--wRRV7LY7NUeQGEoC
Content-Type: text/plain; charset=us-ascii
Content-Disposition: attachment; filename="dmesg.acpi"
NetBSD 1.6Q (ACPI) #0: Tue Apr 8 15:26:04 CEST 2003
bouyer@pop:/local/pop1/bouyer/tmp/i386/obj/local/pop1/bouyer/current/src/sys/arch/i386/compile/ACPI
total memory = 254 MB
avail memory = 228 MB
using 3277 buffers containing 13108 KB of memory
BIOS32 rev. 0 found at 0xfd871
mainbus0 (root)
cpu0 at mainbus0: (uniprocessor)
cpu0: Intel Mobile Pentium III (686-class), 795.45 MHz, id 0x6b4
cpu0: features 383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR>
cpu0: features 383f9ff<PGE,MCA,CMOV,PAT,PSE36,MMX>
cpu0: features 383f9ff<FXSR,SSE>
cpu0: I-cache 16 KB 32b/line 4-way, D-cache 16 KB 32b/line 4-way
cpu0: L2 cache 512 KB 32b/line 8-way
cpu0: ITLB 32 4 KB entries 4-way, 2 4 MB entries fully associative
cpu0: DTLB 64 4 KB entries 4-way, 8 4 MB entries 4-way
cpu0: 16 page colors
acpi0 at mainbus0
acpi0: X/RSDT: OemId <SONY ,C1 ,20020708>, AslId <PTL ,00000000>
acpi0: SCI interrupting at int 9
ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
acpi: activated SNY6001
acpilid0 at acpi0 (PNP0C0D): ACPI Lid Switch
acpibut0 at acpi0 (PNP0C0C): ACPI Power Button
PNP0A03 [PCI Bus] at acpi0 not configured
PNP0C02 [Plug and Play motherboard register resources] at acpi0 not configured
PNP0200 [AT DMA Controller] at acpi0 not configured
npx1 at acpi0 (PNP0C04)
npx1: io 0xf0-0xff irq 13
npx1: using exception 16
PNP0000 [AT Interrupt Controller] at acpi0 not configured
PNP0B00 [AT Real-Time Clock] at acpi0 not configured
PNP0800 [AT-style speaker sound] at acpi0 not configured
PNP0100 [AT Timer] at acpi0 not configured
pckbc1 at acpi0 (PNP0303): kbd port
pckbc1: io 0x60,0x64 irq 1
SNY9001 at acpi0 not configured
acpiec0 at acpi0 (PNP0C09): ACPI Embedded Controller
acpiec0: io 0x62,0x66
acpibat0 at acpi0 (PNP0C0A-1): ACPI Battery (Control Method)
acpiacad0 at acpi0 (ACPI0003): ACPI AC Adapter
spic0 at acpi0 (SNY6001): Sony Programmable I/O Controller
spic0: io 0x1080-0x109f irq 11
wsmouse0 at spic0 mux 0
SNY5001 at acpi0 not configured
com3 at acpi0 (PNP0501)
com3: io 0x3f8-0x3ff irq 4
com3: ns16550a, working fifo
lpt3 at acpi0 (PNP0401)
lpt3: io 0x378-0x37f,0x778-0x77f irq 7 drq 3
fdc1 at acpi0 (PNP0700)
fdc1: io 0x3f0-0x3f5,0x3f7 irq 6 drq 2
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
acpitz0 at acpi0 (): ACPI Thermal Zone
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc1 (aux slot)
pckbc1: unable to establish interrupt for aux slot
wsmouse1 at pms0 mux 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: Intel 82830MP CPU to I/O Bridge 1 (rev. 0x04)
agp0 at pchb0: detected 892k stolen memory
agp0: aperture size is 128M
: aperture at 0xe8000000, size 0x8000000
vga1 at pci0 dev 2 function 0: Intel 82830MP Integrated Video (rev. 0x04)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
Intel 82830MP Integrated Video (miscellaneous display) at pci0 dev 2 function 1 not configured
uhci0 at pci0 dev 29 function 0: Intel 82801CA/CAM USB Controller (rev. 0x02)
uhci0: interrupting at irq 9
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 29 function 1: Intel 82801CA/CAM USB Controller (rev. 0x02)
uhci1: interrupting at irq 9
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2 at pci0 dev 29 function 2: Intel 82801CA/CAM USB Controller (rev. 0x02)
uhci2: interrupting at irq 9
usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
ppb0 at pci0 dev 30 function 0: Intel 82801BAM Hub-to-PCI Bridge (rev. 0x42)
pci1 at ppb0 bus 2
pci1: i/o space, memory space enabled
Texas Instruments TSB43AA22/A OHCI IEEE 1394 Host Controller (Firewire serial bus, interface 0x10) at pci1 dev 2 function 0 not configured
cbb0 at pci1 dev 5 function 0: Ricoh 5C475 PCI-CardBus bridge (rev. 0x80)
fxp0 at pci1 dev 8 function 0: Intel PRO/100 VE Network Controller, rev 66
fxp0: interrupting at irq 9
fxp0: Ethernet address 08:00:46:77:e9:af
inphy0 at fxp0 phy 1: i82562ET 10/100 media interface, rev. 0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
wi0 at pci1 dev 11 function 0: Intersil Prism2.5 Wireless Lan
pci_intr_map: no mapping for pin D (line=ff)
wi0: couldn't map interrupt
cbb0: interrupting at irq 3
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 0 device 0
pcmcia0 at cardslot0
pcib0 at pci0 dev 31 function 0
pcib0: Intel 82801CAM LPC Interface (rev. 0x02)
pciide0 at pci0 dev 31 function 1: Intel 82801CA IDE Controller (ICH3) (rev. 0x02)
pciide0: bus-master DMA support present
pciide0: primary channel wired to compatibility mode
wd0 at pciide0 channel 0 drive 0: <IC25N040ATCS04-0>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 38154 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 78140160 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
pciide0: primary channel interrupting at irq 14
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA data transfers)
pciide0: secondary channel wired to compatibility mode
pciide0: disabling secondary channel (no drives)
Intel 82801CA/CAM SMBus Controller (SMBus serial bus, revision 0x02) at pci0 dev 31 function 3 not configured
auich0 at pci0 dev 31 function 5: i82801CA (ICH3) AC-97 Audio
auich0: can't map codec i/o space
Intel 82801CA/CAM Modem (modem communications, revision 0x02) at pci0 dev 31 function 6 not configured
isa0 at pcib0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
isapnp0: no ISA Plug 'n Play devices found
Kernelized RAIDframe activated
umass0 at uhub2 port 1 configuration 1 interface 0
umass0: Sony USB Memory Stick Slot, rev 1.10/1.09, addr 2
umass0: using ATAPI over CBI
atapibus0 at umass0 channel 0: 2 targets
probe(umass0:0:0): generic HBA error
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
--wRRV7LY7NUeQGEoC--