On 2002.06.21 09:23, Christoph Kaegi wrote:
> I have the opportunity to order two Transtec X1001WIR14
> 1 height unit 19" servers instead of netras, so I need
> to know, if NetBSD would run on them.
> 
> They have are based on a Intel 845 chipset. Is this 
> supported by NetBSD?
> 

Just to report back, so the information is online:

The Transtec X1001WIR14 is actually a Supermicro 
Superserver 5012B-E, based on their own Super P4SBE 
Motherboard.

The board and the system itself are well documented
(from an admins viewpoint) and the docs are
available as PDFs from the supermicro.com site.

Everything I need is supported, even the lm sensors!

The 1.5.3 GENERIC dmesg looks as follows:

-------------------------------------- 8< --------------------------------------
NetBSD 1.5.3 (GENERIC) #34: Mon Jul  1 21:36:06 CEST 2002
    he@hamster.urc.uninett.no:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel (null) (686-class), 1599.91 MHz
total memory = 511 MB
avail memory = 468 MB
using 6573 buffers containing 26292 KB of memory
BIOS32 rev. 0 found at 0xfb330
mainbus0 (root)
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled
pchb0 at pci0 dev 0 function 0
pchb0: Intel product 0x1a30 (rev. 0x04)
ppb0 at pci0 dev 1 function 0: Intel product 0x1a31 (rev. 0x04)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
ppb1 at pci0 dev 30 function 0: Intel 82801BA Hub-to-PCI Bridge (rev. 0x05)
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled
fxp0 at pci2 dev 6 function 0: i82559 Ethernet, rev 8
fxp0: interrupting at irq 10
fxp0: WARNING: Disabling dynamic standby mode in EEPROM to work around a
fxp0: WARNING: hardware bug.  You must reset the system before using this
fxp0: WARNING: interface.
fxp0: new EEPROM ID: 0x40e0
fxp0: EEPROM checksum @ 0x3f: 0x5298 -> 0x529a
fxp0: Ethernet address 00:30:48:51:49:bf
inphy0 at fxp0 phy 1: i82555 10/100 media interface, rev. 4
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp1 at pci2 dev 7 function 0: i82559 Ethernet, rev 8
fxp1: interrupting at irq 11
fxp1: WARNING: Disabling dynamic standby mode in EEPROM to work around a
fxp1: WARNING: hardware bug.  You must reset the system before using this
fxp1: WARNING: interface.
fxp1: new EEPROM ID: 0x40e0
fxp1: EEPROM checksum @ 0x3f: 0x5498 -> 0x549a
fxp1: Ethernet address 00:30:48:51:49:bd
inphy1 at fxp1 phy 1: i82555 10/100 media interface, rev. 4
inphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
vga1 at pci2 dev 8 function 0: ATI Technologies product 0x4752 (rev. 0x27)
wsdisplay0 at vga1: console (80x25, vt100 emulation)
pcib0 at pci0 dev 31 function 0
pcib0: Intel 82801BA LPC Interface Bridge (rev. 0x05)
pciide0 at pci0 dev 31 function 1: Intel 82801BA IDE Controller (ICH2) (rev. 0x05)
pciide0: bus-master DMA support present
pciide0: primary channel wired to compatibility mode
wd0 at pciide0 channel 0 drive 0: <ST340810A>
wd0: drive supports 16-sector pio transfers, lba addressing
wd0: 38166 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 78165360 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5
wd1 at pciide0 channel 0 drive 1: <ST340810A>
wd1: drive supports 16-sector pio transfers, lba addressing
wd1: 38166 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 78165360 sectors
wd1: 32-bit data port
wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5
pciide0: primary channel interrupting at irq 14
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (using DMA data transfers)
wd1(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 5 (using DMA data transfers)
pciide0: secondary channel wired to compatibility mode
atapibus0 at pciide0 channel 1
cd0 at atapibus0 drive 0: <MATSHITA CR-177, , 7T0D> type 5 cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2
pciide0: secondary channel interrupting at irq 15
cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2 (using DMA data transfers)
uhci0 at pci0 dev 31 function 2: Intel 82801BA USB Controller (rev. 0x05)
uhci0: interrupting at irq 5
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
Intel 82801BA SMBus Controller (SMBus serial bus, revision 0x05) at pci0 dev 31 function 3 not configured
uhci1 at pci0 dev 31 function 4: Intel 82801BA USB Controller (rev. 0x05)
uhci1: interrupting at irq 12
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
isa0 at pcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
lpt0 at isa0 port 0x378-0x37b irq 7
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff: using exception 16
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
isapnp0: no ISA Plug 'n Play devices found
biomask f365 netmask ff65 ttymask ffe7
wd1: no disk label
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
-------------------------------------- 8< --------------------------------------

-- 
----------------------------------------------------------------------
Christoph Kaegi                                           kgc@zhwin.ch
----------------------------------------------------------------------