Peter Seebach writes:
> Right - you have to have reset the CMOS first, by shorting the CMOS jumpers
> for at least 60 seconds.  I think you may have to plug the unit in once while
> the jumpers are shorted, *then* give it 60 seconds.

Thanks - this did it.  My IA-1 has now successfully booted a NetBSD
1.5.2 boot-big.fs floppy image from a 64 MB CompactFlash card.  The
dmesg output is enclosed below.
-- 
Andreas Gustafsson, gson@nominum.com

NetBSD 1.5.2 (INSTALL) #3: Sat Aug 18 23:52:07 CEST 2001
    he@hamster.urc.uninett.no:/usr/src/sys/arch/i386/compile/INSTALL
cpu0: AMD K6-2 (586-class), 267.33 MHz
total memory = 30336 KB
avail memory = 23228 KB
using 404 buffers containing 1616 KB of memory
BIOS32 rev. 0 found at 0xfa120
mainbus0 (root)
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x1106 product 0x0501 (rev. 0x04)
ppb0 at pci0 dev 1 function 0: vendor 0x1106 product 0x8501 (rev. 0x00)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
vendor 0x1023 product 0x8420 (VGA display, revision 0x5d) at pci1 dev 0 function 0 not configured
vendor 0x11c1 product 0x0441 (miscellaneous communications, revision 0x01) at pci0 dev 4 function 0 not configured
pcib0 at pci0 dev 7 function 0
pcib0: vendor 0x1106 product 0x0686 (rev. 0x1b)
pciide0 at pci0 dev 7 function 1: VIA Technologies VT82C686A (Apollo KX133) ATA66 controller
pciide0: bus-master DMA support present
pciide0: primary channel configured to compatibility mode
wd0 at pciide0 channel 0 drive 0: <SanDisk SDP3B-16>
wd0: drive supports 1-sector pio transfers, lba addressing
wd0: 15680 KB, 490 cyl, 2 head, 32 sec, 512 bytes/sect x 31360 sectors
wd0: 32-bit data port
pciide0: primary channel interrupting at irq 14
wd0(pciide0:0:0): using PIO mode 0
pciide0: secondary channel configured to compatibility mode
wd1 at pciide0 channel 1 drive 0: <SanDisk SDCFB-64>
wd1: drive supports 1-sector pio transfers, lba addressing
wd1: 62720 KB, 490 cyl, 8 head, 32 sec, 512 bytes/sect x 125440 sectors
wd1: 32-bit data port
pciide0: secondary channel interrupting at irq 15
wd1(pciide0:1:0): using PIO mode 0
uhci0 at pci0 dev 7 function 2: vendor 0x1106 product 0x3038 (rev. 0x0e)
uhci0: interrupting at irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: vendor 0x1106 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 7 function 3: vendor 0x1106 product 0x3038 (rev. 0x0e)
uhci1: interrupting at irq 11
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: vendor 0x1106 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
vendor 0x1106 product 0x3057 (miscellaneous bridge, revision 0x20) at pci0 dev 7 function 4 not configured
vendor 0x1106 product 0x3058 (audio multimedia, revision 0x21) at pci0 dev 7 function 5 not configured
vendor 0x1106 product 0x3068 (miscellaneous communications, revision 0x20) at pci0 dev 7 function 6 not configured
isa0 at pcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff: using exception 16
pc0 at isa0 port 0x60-0x6f irq 1: color
pc0: console
isapnp0: no ISA Plug 'n Play devices found
biomask ffe5 netmask ffe5 ttymask ffe7
md0: internal 2048K image area
wd0: no disk label
boot device: wd1
root on md0a dumps on md0b
root file system type: ffs