--=-=-=

Christoph Kaegi <kgc@zhwin.ch> writes:

> The generic kernel boots fine, but when I try to boot a
> customizezed kernel, it just stops booting at the following
> line:
> 
> ------------------------------ 8< ------------------------------
> ..
> sysbeep0 at pcppi0
> npx0 at isa0 port 0xf0-0xff: using exception 16
> fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
> fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
> biomask 6f65 netmask ef65 ttymask ffe7
> ------------------------------ 8< ------------------------------

AOL! I have the same problem, but I haven't had time to investigate.

GENERIC works fine on this machine, but my custom config (which worked
with a 1.5.1_BETA2 snapshot) hangs at the "same" spot as yours. I
attach the config, and a dmesg from GENERIC.


Best wishes,
   --Daniel



--=-=-=
Content-Disposition: attachment; filename=EBBOT
Content-Description: custom kernel config

#	$NetBSD: GENERIC,v 1.354.2.15 2001/05/06 15:18:54 he Exp $
#
#	GENERIC -- everything that's currently supported
#

include "arch/i386/conf/std.i386"

#ident 		"GENERIC-$Revision: 1.354.2.15 $"

maxusers	32		# estimated number of users

# CPU support.  At least one is REQUIRED.
options 	I586_CPU
options 	I686_CPU

# CPU-related options.
options 	VM86		# virtual 8086 emulation
options 	USER_LDT	# user-settable LDT; used by WINE
# eliminate delay no-ops in I/O; recommended on all but very old machines
options 	DUMMY_NOPS

# delay between "rebooting ..." message and hardware reset, in milliseconds
#options 	CPURESET_DELAY=2000

# This option allows you to force a serial console at the specified
# I/O address.   see console(4) for details.
#options 	"CONSDEVNAME=\"com\"",CONADDR=0x2f8,CONSPEED=57600
#	you don't want the option below ON iff you are using the
#	serial console option of the new boot strap code.
#options 	CONS_OVERRIDE	# Always use above! independent of boot info

# The following options override the memory sizes passed in from the boot
# block.  Use them *only* if the boot block is unable to determine the correct
# values.  Note that the BIOS may *correctly* report less than 640k of base
# memory if the extended BIOS data area is located at the top of base memory
# (as is the case on most recent systems).
#options 	REALBASEMEM=639		# size of base memory (in KB)
#options 	REALEXTMEM=15360	# size of extended memory (in KB)

# Standard system options

options 	UCONSOLE	# users can use TIOCCONS (for xconsole)
options 	INSECURE	# disable kernel security levels

options 	RTC_OFFSET=0	# hardware clock is this many mins. west of GMT
options 	NTP		# NTP phase/frequency locked loop

options 	KTRACE		# system call tracing via ktrace(1)

options 	SYSVMSG		# System V-like message queues
options 	SYSVSEM		# System V-like semaphores
options 	SYSVSHM		# System V-like memory sharing
#options 	SHMMAXPGS=1024	# 1024 pages is the default

options 	LKM		# loadable kernel modules

# Diagnostic/debugging support options
#options 	DIAGNOSTIC	# expensive kernel consistency checks
#options 	DEBUG		# expensive debugging checks/support
options 	KMEMSTATS	# kernel memory statistics (vmstat -m)
options 	DDB		# in-kernel debugger
#options 	DDB_HISTORY_SIZE=512	# enable history editing in DDB
#options 	KGDB		# remote debugger
#options 	"KGDB_DEVNAME=\"com\"",KGDBADDR=0x3f8,KGDBRATE=9600
#makeoptions	DEBUG="-g"	# compile full symbol table

# Compatibility options
options 	COMPAT_NOMID	# compatibility with 386BSD, BSDI, NetBSD 0.8,
options 	COMPAT_14	# NetBSD 1.4,
options 	COMPAT_43	# and 4.3BSD

options 	COMPAT_SVR4	# binary compatibility with SVR4
options 	COMPAT_IBCS2	# binary compatibility with SCO and ISC
options 	COMPAT_LINUX	# binary compatibility with Linux
options 	COMPAT_FREEBSD	# binary compatibility with FreeBSD
#options 	COMPAT_PECOFF   # kernel support to run Win32 apps

# File systems
file-system 	FFS		# UFS
#file-system 	EXT2FS		# second extended file system (linux)
file-system 	LFS		# log-structured file system
file-system 	MFS		# memory file system
file-system 	NFS		# Network File System client
file-system 	NTFS		# Windows/NT file system (experimental)
file-system 	CD9660		# ISO 9660 + Rock Ridge file system
file-system 	MSDOSFS		# MS-DOS file system
file-system 	FDESC		# /dev/fd
file-system 	KERNFS		# /kern
file-system 	NULLFS		# loopback file system
#file-system 	OVERLAY		# overlay file system
#file-system 	PORTAL		# portal filesystem (still experimental)
file-system 	PROCFS		# /proc
file-system 	UMAPFS		# NULLFS + uid and gid remapping
file-system 	UNION		# union file system
#file-system	CODA		# Coda File System; also needs vcoda (below)

# File system options
#options 	QUOTA		# UFS quotas
#options 	FFS_EI		# FFS Endian Independent support
options 	SOFTDEP         # FFS soft updates support.
options 	NFSSERVER	# Network File System server
#options 	EXT2FS_SYSTEM_FLAGS # makes ext2fs file flags (append and
				# immutable) behave as system flags.

# Networking options
#options 	GATEWAY		# packet forwarding
options 	INET		# IP + ICMP + TCP + UDP
options 	INET6		# IPV6
options 	IPSEC		# IP security
options 	IPSEC_ESP	# IP security (encryption part; define w/IPSEC)
#options 	IPSEC_DEBUG	# debug for IP security
#options 	MROUTING	# IP multicast routing
options 	PPP_BSDCOMP	# BSD-Compress compression support for PPP
options 	PPP_DEFLATE	# Deflate compression support for PPP
options 	PPP_FILTER	# Active filter support for PPP (requires bpf)
options 	PFIL_HOOKS	# pfil(9) packet filter hooks
options 	IPFILTER_LOG	# ipmon(8) log support

# These options enable verbose messages for several subsystems.
# Warning, these may compile large string tables into the kernel!
options 	MIIVERBOSE	# verbose PHY autoconfig messages
options 	PCIVERBOSE	# verbose PCI device autoconfig messages
#options 	PCI_CONFIG_DUMP	# verbosely dump PCI config space
#options 	PCMCIAVERBOSE	# verbose PCMCIA configuration messages
#options 	SCSIVERBOSE	# human readable SCSI error messages
options 	USBVERBOSE	# verbose USB device autoconfig messages
options 	PNPBIOSVERBOSE	# verbose PnP BIOS messages
#options	PNPBIOSDEBUG	# more fullsome Pnp BIOS debugging messages
options 	NFS_BOOT_DHCP,NFS_BOOT_BOOTPARAM

#
# wscons options
#
# builtin terminal emulations
#options 	WSEMUL_SUN		# sun terminal emulation
options 	WSEMUL_VT100		# VT100 / VT220 emulation
# different kernel output - see dev/wscons/wsdisplayvar.h
options 	WS_KERNEL_FG=WSCOL_GREEN
#options 	WS_KERNEL_BG=WSCOL_BLACK
# compatibility to other console drivers
options 	WSDISPLAY_COMPAT_PCVT		# emulate some ioctls
options 	WSDISPLAY_COMPAT_SYSCONS	# emulate some ioctls
options 	WSDISPLAY_COMPAT_USL		# VT handling
options 	WSDISPLAY_COMPAT_RAWKBD		# can get raw scancodes
# see dev/pckbc/wskbdmap_mfii.c for implemented layouts
#options 	PCKBD_LAYOUT="(KB_DE | KB_NODEAD)"
# allocate a number of virtual screens at autoconfiguration time
#options 	WSDISPLAY_DEFAULTSCREENS=4
# use a large software cursor that doesn't blink
options 	PCDISPLAY_SOFTCURSOR

# Kernel root file system and dump configuration.
config		netbsd	root on ? type ?
#config		netbsd	root on sd0a type ffs
#config		netbsd	root on ? type nfs

#
# Device configuration
#

mainbus0 at root

#apm0	at mainbus0			# Advanced power management

# Tuning for power management, see apm(4) for more details.
#options 	APM_NO_IDLE		# Don't call BIOS CPU idle function
#options 	APM_V10_ONLY		# Use only the APM 1.0 calls
#options 	APM_NO_POWEROFF		# Don't power off on halt(8)
#options 	APM_POWER_PRINT		# Print stats on the console
#options 	APM_DISABLE_INTERRUPTS=0 # Don't disable interrupts


# Basic Bus Support

# Plug-and-Play BIOS and attached devices

#pnpbios*	at mainbus?


# com port
# If enabled, consider changing "com0", "com1", and "com2" under "ISA Serial
# Interfaces" to "com*", otherwise com2 will attach at pnpbios? and there
# will be no com0.  A side effect is pcmcia (and other) com? previously
# starting at com3 may attach as com1 or com2.
#com*		at pnpbios? index ?	# serial ports

# parallel port
# The above "com*" comments apply, cf. "lpt0" under "ISA parallel
# "printer interfaces".
#lpt*		at pnpbios? index ?	# parallel ports

#pckbc*		at pnpbios? index ?	# PC keyboard/mouse controller
#fdc*		at pnpbios? index ?	# floppy controller

# IDE controller on Toshiba Portege 3000 series (crippled PCI device)
#pciide* at pnpbios? index ?

# PCI bus support
pci*	at mainbus? bus ?
pci*	at pchb? bus ?
pci*	at ppb? bus ?

# Configure PCI using BIOS information
options 	PCIBIOS			# PCI BIOS support
options 	PCIBIOSVERBOSE		# PCI BIOS verbose info
options 	PCIBIOS_ADDR_FIXUP	# fixup PCI I/O addresses
options 	PCIBIOS_BUS_FIXUP	# fixup PCI bus numbering
options 	PCIBIOS_INTR_FIXUP	# fixup PCI interrupt routing
#options 	PCIBIOS_IRQS_HINT=0x0a00 # PCI interrupts hint. IRQ 9 or 11
#options 	PCIBIOS_INTR_GUESS	# see pcibios(4)
#options 	PCIINTR_DEBUG		# super-verbose PCI interrupt fixup

# PCI bridges
pchb*	at pci? dev ? function ?	# PCI-Host bridges
pcib*	at pci? dev ? function ?	# PCI-ISA bridges
ppb*	at pci? dev ? function ?	# PCI-PCI bridges
# XXX 'puc's aren't really bridges, but there's no better place for them here
puc*	at pci? dev ? function ?	# PCI "universal" comm. cards

# ISA bus support
isa*	at mainbus?
isa*	at pcib?

# PCMCIA bus support
pcmcia*	at pcic? controller ? socket ?
pcmcia*	at tcic? controller ? socket ?

# ISA PCMCIA controllers
pcic0	at isa? port 0x3e0 iomem 0xd0000 iosiz 0x10000
pcic1	at isa? port 0x3e2 iomem 0xe0000 iosiz 0x4000
tcic0	at isa? port 0x240 iomem 0xd0000 iosiz 0x10000

# PCI PCMCIA controllers
pcic0	at pci? dev? function ?

# ISA Plug-and-Play bus support
isapnp0	at isa?

# ISA Plug-and-Play PCMCIA controllers
pcic*	at isapnp?

# CardBus bridge support
#cbb*		at pci? dev ? function ?
#cardslot*	at cbb?	

# CardBus bus support
#cardbus*	at cardslot?
#pcmcia* 	at cardslot?

# Coprocessor Support

# Math Coprocessor support
npx0	at isa? port 0xf0 irq 13	# x86 math coprocessor


# Console Devices


# wscons
pckbc0		at isa?			# pc keyboard controller
pckbd*		at pckbc?		# PC keyboard
# "opms" should not be enabled together with "pms" or "pmsi"
pms*		at pckbc?		# PS/2 mouse for wsmouse
pmsi*		at pckbc?		# PS/2 "Intelli"mouse for wsmouse
vga0		at isa?
vga*		at pci? dev ? function ?
pcdisplay0	at isa?			# CGA, MDA, EGA, HGA
wsdisplay*	at vga? console ?
wsdisplay*	at pcdisplay? console ?
wskbd* 		at pckbd? console ?
wsmouse*	at pms? mux 0
wsmouse*	at pmsi? mux 0

pcppi0		at isa?
sysbeep0	at pcppi?

# Serial Devices

# PCI serial interfaces
com*	at puc? port ?			# 16x50s on "universal" comm boards

# ISA Plug-and-Play serial interfaces
com*	at isapnp?			# Modems and serial boards

# PCMCIA serial interfaces
com*	at pcmcia? function ?		# Modems and serial cards

pcmcom*	at pcmcia? function ?		# PCMCIA multi-port serial cards
com*	at pcmcom? slave ?		# ...and the slave devices

# CardBus serial interfaces
#com*	at cardbus? function ?		# Modems and serial cards

# ISA serial interfaces
#options 	COM_HAYESP		# adds Hayes ESP serial board support
com0	at isa? port 0x3f8 irq 4	# Standard PC serial ports
com1	at isa? port 0x2f8 irq 3
com2	at isa? port 0x3e8 irq 5

# Parallel Printer Interfaces

# PCI parallel printer interfaces
lpt*	at puc? port ?			# || ports on "universal" comm boards

# ISA parallel printer interfaces
lpt0	at isa? port 0x378 irq 7	# standard PC parallel ports
lpt1	at isa? port 0x278
lpt2	at isa? port 0x3bc

# LM7[89] and compatible hardware monitors
#lm0	at isa?	port 0x290		# other common ports: 0x280, 0x310

# VIA VT82C686A hardware monitor
viapm*	at pci? dev ? function ?
viaenv* at viapm?


# IDE and related devices
# PCI IDE controllers - see pciide(4) for supported hardware.
# The 0x0001 flag force the driver to use DMA, even if the driver doesn't know
# how to set up DMA modes for this chip. This may work, or may cause
# a machine hang with some controllers.
pciide* at pci? dev ? function ? flags 0x0000

# ISA Plug-and-Play IDE controllers
wdc*	at isapnp? 

# PCMCIA IDE controllers
wdc*	at pcmcia? function ?

# ISA ST506, ESDI, and IDE controllers
# Use flags 0x01 if you want to try to use 32bits data I/O (the driver will
# fall back to 16bits I/O if 32bits I/O are not functional).
# Some controllers pass the initial 32bit test, but will fail later.
wdc0	at isa? port 0x1f0 irq 14 flags 0x00
wdc1	at isa? port 0x170 irq 15 flags 0x00

# IDE drives
# Flags are used only with controllers that support DMA operations
# and mode settings (e.g. some pciide controllers)
# The lowest order four bits (rightmost digit) of the flags define the PIO
# mode to use, the next set of four bits the DMA mode and the third set the
# UltraDMA mode. For each set of four bits, the 3 lower bits define the mode
# to use, and the last bit must be 1 for this setting to be used.
# For DMA and UDMA, 0xf (1111) means 'disable'.
# 0x0fac means 'use PIO mode 4, DMA mode 2, disable UltraDMA'.
# (0xc=1100, 0xa=1010, 0xf=1111)
# 0x0000 means "use whatever the drive claims to support".
wd*	at wdc? channel ? drive ? flags 0x0000
wd*	at pciide? channel ? drive ? flags 0x0000

# ATAPI bus support
atapibus* at wdc? channel ?
atapibus* at pciide? channel ?

# ATAPI devices
# flags have the same meaning as for IDE drives.
cd*	at atapibus? drive ? flags 0x0000	# ATAPI CD-ROM drives
sd*	at atapibus? drive ? flags 0x0000	# ATAPI disk drives
uk*	at atapibus? drive ? flags 0x0000	# ATAPI unknown


# Miscellaneous mass storage devices

# ISA floppy
fdc0	at isa? port 0x3f0 irq 6 drq 2	# standard PC floppy controllers
fd*	at fdc? drive ?			# the drives themselves


# Network Interfaces

# PCI network interfaces
de*	at pci? dev ? function ?	# DEC 21x4x-based Ethernet
ep*	at pci? dev ? function ?	# 3Com 3c59x
ex*	at pci? dev ? function ?	# 3Com 90x[B]
fxp*	at pci? dev ? function ?	# Intel EtherExpress PRO 10+/100B
tlp*	at pci? dev ? function ?	# DECchip 21x4x (and clones) Ethernet
#options 	TLP_MATCH_21040
#options 	TLP_MATCH_21041
#options 	TLP_MATCH_21140
#options 	TLP_MATCH_21142

# PCMCIA network interfaces
ne*	at pcmcia? function ?		# NE2000-compatible Ethernet

# ISA network interfaces
ep*	at isa? port ? irq ?			# 3C509 ethernet cards
ne0	at isa? port 0x280 irq 9		# NE[12]000 ethernet cards
ne1	at isa? port 0x300 irq 10
sm0	at isa? port 0x300 irq 10		# SMC91C9x Ethernet

# MII/PHY support
exphy*	at mii? phy ?			# 3Com internal PHYs
icsphy*	at mii? phy ?			# Integrated Circuit Systems ICS1890
inphy*	at mii? phy ?			# Intel 82555 PHYs
iophy*	at mii? phy ?			# Intel 82553 PHYs
nsphy*	at mii? phy ?			# NS83840 PHYs
nsphyter* at mii? phy ?			# NS83843 PHYs
qsphy*	at mii? phy ?			# Quality Semiconductor QS6612 PHYs
sqphy*	at mii? phy ?			# Seeq 80220/80221/80223 PHYs
tqphy*	at mii? phy ?			# TDK Semiconductor PHYs
ukphy*	at mii? phy ?			# generic unknown PHYs

# USB Controller and Devices

# PCI USB controllers
ohci*	at pci?	dev ? function ?	# Open Host Controller
uhci*	at pci?	dev ? function ?	# Universal Host Controller (Intel)

# USB bus support
usb*	at ohci?
usb*	at uhci?

# USB Hubs
uhub*	at usb?
uhub*	at uhub? port ? configuration ? interface ?

# USB Mice
ums*	at uhub? port ? configuration ? interface ?
wsmouse*	at ums? mux 0

# USB Keyboards
ukbd*	at uhub? port ? configuration ? interface ?
wskbd*	at ukbd? console ? mux 1

# USB Generic HID devices
uhid*	at uhub? port ? configuration ? interface ?

# USB Printer
ulpt*	at uhub? port ? configuration ? interface ?

# USB Modem
umodem*	at uhub? port ? configuration ?
ucom*	at umodem?

# USB Mass Storage
umass*	at uhub? port ? configuration ? interface ?
atapibus* at umass? channel ?
scsibus* at umass? channel ?

# USB audio
uaudio*	at uhub? port ? configuration ?

# USB Ethernet adapters
aue*	at uhub? port ?		# ADMtek AN986 Pegasus based adapters
cue*	at uhub? port ?		# CATC USB-EL1201A based adapters
kue*	at uhub? port ?		# Kawasaki LSI KL5KUSB101B based adapters

# Prolofic PL2301/PL2302 host-to-host adapter
upl*	at uhub? port ?

# Serial adapters
# FTDI FT8U100AX serial adapter
#uftdi*	at uhub? port ?
#ucom*	at uftdi? portno ?

# Diamond Multimedia Rio 500
urio*	at uhub? port ?

# USB Handspring Visor
uvisor*	at uhub? port ?
ucom*	at uvisor?

# USB Generic driver
ugen*	at uhub? port ?

# Audio Devices

# PCI audio devices
#auvia*	at pci? dev ? function ?	# VIA VT82C686A integrated AC'97 Audio

# Audio support
#audio*	at auvia?
audio*	at uaudio?

# The spkr driver provides a simple tone interface to the built in speaker.
spkr0	at pcppi?		# PC speaker

# TV cards

# Brooktree 848/849/878/879 based TV cards
bktr* at pci? dev ? function ?

# Pseudo-Devices

# disk/mass storage pseudo-devices
pseudo-device	ccd		4	# concatenated/striped disk devices
pseudo-device	raid		4	# RAIDframe disk driver
#options 	RAID_AUTOCONFIG		# auto-configuration of RAID components
pseudo-device	md		1	# memory disk device (ramdisk)
pseudo-device	vnd		4	# disk-like interface to files

# network pseudo-devices
pseudo-device	bpfilter	8	# Berkeley packet filter
pseudo-device	ipfilter		# IP filter (firewall) and NAT
pseudo-device	loop			# network loopback
pseudo-device	ppp		2	# Point-to-Point Protocol
#pseudo-device	sl		2	# Serial Line IP
pseudo-device	tun		2	# network tunneling over tty
pseudo-device	gre		2	# generic L3 over IP tunnel
pseudo-device	ipip		2	# IP Encapsulation within IP (RFC 2003)
pseudo-device	gif		4	# IPv[46] over IPv[46] tunnel (RFC1933)
pseudo-device	faith		1	# IPv[46] tcp relay translation i/f
pseudo-device	stf		1	# 6to4 IPv6 over IPv4 encapsulation
pseudo-device	vlan			# IEEE 802.1q encapsulation

# miscellaneous pseudo-devices
pseudo-device	pty		64	# pseudo-terminals
# rnd works; RND_COM does not on port i386 yet.
pseudo-device	rnd			# /dev/random and in-kernel generator
#options 	RND_COM			# use "com" randomness as well (BROKEN)

# a pseudo device needed for Coda	# also needs CODA (above)
#pseudo-device	vcoda		4	# coda minicache <-> venus comm.

# mouse & keyboard multiplexor pseudo-devices
pseudo-device	wsmux		2

--=-=-=
Content-Disposition: attachment; filename=dmesg.boot
Content-Description: dmesg

NetBSD 1.5.1 (GENERIC) #3: Tue Jun 19 18:26:32 CEST 2001
    dne@ebbot:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: AMD Athlon Model 2 (686-class), 750.08 MHz
total memory = 127 MB
avail memory = 113 MB
using 1658 buffers containing 6632 KB of memory
BIOS32 rev. 0 found at 0xfb4a0
mainbus0 (root)
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled
pchb0 at pci0 dev 0 function 0
pchb0: VIA Technologies VT8371 (Apollo KX133) Host Bridge (rev. 0x02)
ppb0 at pci0 dev 1 function 0: VIA Technologies VT8371 (Apollo KX133) PCI-PCI Bridge (rev. 0x00)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
vga1 at pci1 dev 0 function 0: Nvidia Corporation RIVA TNT2 Model 64 (rev. 0x11)
wsdisplay0 at vga1: console (80x25, vt100 emulation)
pcib0 at pci0 dev 7 function 0
pcib0: VIA Technologies VT82C686A (Apollo KX133) PCI-ISA Bridge (rev. 0x22)
pciide0 at pci0 dev 7 function 1: VIA Technologies VT82C686A (Apollo KX133) ATA66 controller
pciide0: bus-master DMA support present
pciide0: primary channel configured to compatibility mode
wd0 at pciide0 channel 0 drive 0: <IBM-DTLA-307030>
wd0: drive supports 16-sector pio transfers, lba addressing
wd0: 29314 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 60036480 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5
wd1 at pciide0 channel 0 drive 1: <Maxtor 91008D7>
wd1: drive supports 16-sector pio transfers, lba addressing
wd1: 9617 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 19696320 sectors
wd1: 32-bit data port
wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2
pciide0: primary channel interrupting at irq 14
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 4 (using DMA data transfers)
wd1(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 2 (using DMA data transfers)
pciide0: secondary channel configured to compatibility mode
atapibus0 at pciide0 channel 1
cd0 at atapibus0 drive 0: <Pioneer DVD-ROM ATAPIModel DVD-104S 020, , E2.02> type 5 cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2
pciide0: secondary channel interrupting at irq 15
cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2 (using DMA data transfers)
uhci0 at pci0 dev 7 function 2: VIA Technologies VT83C572 USB Controller (rev. 0x10)
uhci0: interrupting at irq 5
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: VIA Technologie UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 7 function 3: VIA Technologies VT83C572 USB Controller (rev. 0x10)
uhci1: interrupting at irq 5
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: VIA Technologie UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
pchb1 at pci0 dev 7 function 4
pchb1: VIA Technologies VT82C686A SMBus Controller (rev. 0x30)
Creative Labs SBLive! EMU 10000 (audio multimedia, revision 0x08) at pci0 dev 11 function 0 not configured
Creative Labs PCI Gameport Joystick (miscellaneous input, revision 0x08) at pci0 dev 11 function 1 not configured
fxp0 at pci0 dev 15 function 0: Intel i82557 Ethernet, rev 8
fxp0: interrupting at irq 11
fxp0: Ethernet address 00:d0:b7:83:6a:84, 10/100 Mb/s
inphy0 at fxp0 phy 1: i82555 10/100 media interface, rev. 4
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isa0 at pcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
lpt0 at isa0 port 0x378-0x37b irq 7
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff: using exception 16
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
isapnp0: no ISA Plug 'n Play devices found
biomask e765 netmask ef65 ttymask ffe7
uhub2 at uhub0 port 1
uhub2: Nokia Display Products Oy Nokia USB Hub Type P, class 9/0, rev 1.00/1.06, addr 2
uhub2: 5 ports with 4 removable, self powered
uhid0 at uhub2 port 1 configuration 1 interface 0
uhid0: Nokia Display Products Oy Nokia USB Monitor Control, rev 1.00/1.06, addr 3, iclass 3/0
wd1: no disk label
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0

--=-=-=--