This hardware configuration works fine under NetBSD-1.4.2, but fails under NetBSD-1.5
or 1.5.1.

HELP!!  Probe hangs after waiting for devices to settle.

Gerry Simmons
simmons@darykon.cet.com


Here are the dmsgs: (BTW, the INSTALL & GENERIC kernels do the same thing.)

NetBSD 1.5.1 (DAVINCI) #1: Fri Jul 20 08:53:12 PDT 2001
    simmons@davinci:/usr/src/sys/arch/i386/compile/DAVINCI
cpu0: Intel Pentium (P54C) (586-class), 199.44 MHz
total mem = 127 MB
avail mem = 115 MB
using 1659 buffers containing 6636 KB of memory
BIOS32 rev. 0 found at 0xfb330
mainbus0 (root)
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o enabled, memory enabled
pchb0 at pci0 dev 0 function 0
pchb0: Intel 82439HX System Controller (TXC) (rev. 0x02)
pcib0 at pci0 dev 7 function 0
pcib0: Intel 82371SB PCI-to-ISA Bridge (PIIX3) (rev. 0x01)
pciide0 at pci0 dev 7 function 1: Intel 82371SB IDE Interface (PIIX3) (rev. 0x00)
pciide0: bus-master DMA support present
pciide0: primary channel wired to compatibility mode
wd0 at pciide0 channel 0 drive 0: <WDC WD43AA>
wd0: drive supports 16-sector pio transfers, lba addressing
wd0: 4112MB, 8355 cyl, 16 head, 63 sec, 512 bytes/sect x 8421840 sectors
wd0: 32-bits data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 4
pciide0: primary channel interrupting at irq 14
wd0(pciide0:0:0): using PIO mode 4, DMA mode 2 (using DMA data transfers)
pciide0: disabling secondary channel (no drives)
ep0 at pci0 dev 18 function 0: 3Com 3c590 Ethernet
ep0: interrupting at irq 10
ep0: address 00:a0:24:4a:d5:0a, 32KB byte-wide FIFO, 1:1 Rx:Tx split
ep0: 10baseT, 10baseT-FDX, 10base5, 10base2 (default 10baseT)
vga1 at pci0 dev 19 function 0: ATI Technologies product 0x5245 (rev. 0x00)
wsdisplay0 at vga1: console (80x25, vt100 emulation)
isa0 at pcib0
aic0 at isa0 port 0x340-0x35f irq 11
scsibus0 at aic0: 8 targets, 8 luns per target
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
lpt0 at isa0 port 0x378-0x37b irq 7
sb0 at isa0 port 0x220-0x237 irq 5 drq 1 drq2 5: dsp v4.12
audio0 at sb0: full duplex, mmap, independent
midi0 at sb0: SB MIDI UART
opl0 at sb0: model OPL3
midi1 at opl0: SB Yamaha OPL3
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff: using exception 16
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
fd1 at fdc0 drive 1: 1.2MB, 80 cyl, 2 head, 15 sec
isapnp0: no ISA Plug 'n Play devices found
biomask eb45 netmask ef45 ttymask ffc7
scsibus0: waiting 2 seconds for devices to settle ...