Subject: Again..VIA Problem with RealTek EtherCard.
To: port-i386@netbsd.org <port-i386@netbsd.org>
From: Andrea <practive@practive.org>
List: port-i386
Date: 07/05/2001 01:52:50
Hi!
I'm yet trying to build a file-server using NetBSD+RaidFrame+4ATA HD.
But again i'm facing heavy problem in doing this.
The symptom is still the same,when i try to initialize/read/write the
raid volume the network card go away...
The chipset is a VIA686A,the card is a Realtek 8139 and the IDE
controllers are on-board ,changing the card (e.g. using a 3com)
attenuate the problem ,but doesn't resolve it .
I tried a lot of combination ,and every NetBSD release/snapshot from 1.5
to current.
Nowadays is very difficult (near impossible to me) to find motherboard
manufactures that use a different chipset from VIA.....so,i got three
possibilities.
a) Use SCSI devices (very expensive)
b) Find a software workaround/patch/upgrade that will solve this
problem.
c) Buy an Hardware fully supported and of course that is easily
available on market.
Anynone owns a solutions?
Thanks..
This is my kernel config:
# $NetBSD: GENERIC,v 1.408 2001/06/27 13:40:12 darcy Exp $
#
# GENERIC -- everything that's currently supported
#
include "arch/i386/conf/std.i386"
#ident "GENERIC-$Revision: 1.408 $"
maxusers 32 # estimated number of users
# CPU support. At least one is REQUIRED.
options I386_CPU
options I486_CPU
options I586_CPU
options I686_CPU
# CPU-related options.
options MATH_EMULATE # floating point emulation
options VM86 # virtual 8086 emulation
options USER_LDT # user-settable LDT; used by WINE
# eliminate delay no-ops in I/O; recommended on all but very old
machines
#options DUMMY_NOPS
# delay between "rebooting ..." message and hardware reset, in
milliseconds
#options CPURESET_DELAY=2000
# This option allows you to force a serial console at the specified
# I/O address. see console(4) for details.
#options "CONSDEVNAME=\"com\"",CONADDR=0x2f8,CONSPEED=57600
# you don't want the option below ON iff you are using the
# serial console option of the new boot strap code.
#options CONS_OVERRIDE # Always use above! independent of boot
info
# The following options override the memory sizes passed in from the
boot
# block. Use them *only* if the boot block is unable to determine the
correct
# values. Note that the BIOS may *correctly* report less than 640k of
base
# memory if the extended BIOS data area is located at the top of base
memory
# (as is the case on most recent systems).
#options REALBASEMEM=639 # size of base memory (in KB)
#options REALEXTMEM=15360 # size of extended memory (in
KB)
# Standard system options
options UCONSOLE # users can use TIOCCONS (for xconsole)
options INSECURE # disable kernel security levels
options RTC_OFFSET=0 # hardware clock is this many mins. west
of GMT
options NTP # NTP phase/frequency locked loop
options KTRACE # system call tracing via ktrace(1)
options SYSVMSG # System V-like message queues
options SYSVSEM # System V-like semaphores
#options SEMMNI=10 # number of semaphore identifiers
#options SEMMNS=60 # number of semaphores in system
#options SEMUME=10 # max number of undo entries per process
#options SEMMNU=30 # number of undo structures in system
options SYSVSHM # System V-like memory sharing
#options SHMMAXPGS=1024 # 1024 pages is the default
options LKM # loadable kernel modules
# Diagnostic/debugging support options
#options DIAGNOSTIC # expensive kernel consistency checks
#options DEBUG # expensive debugging checks/support
#options KMEMSTATS # kernel memory statistics (vmstat -m)
options DDB # in-kernel debugger
options DDB_HISTORY_SIZE=512 # enable history editing in DDB
#options KGDB # remote debugger
#options "KGDB_DEVNAME=\"com\"",KGDBADDR=0x3f8,KGDBRATE=9600
#makeoptions DEBUG="-g" # compile full symbol table
# Compatibility options
options COMPAT_NOMID # compatibility with 386BSD, BSDI,
NetBSD 0.8,
options COMPAT_09 # NetBSD 0.9,
options COMPAT_10 # NetBSD 1.0,
options COMPAT_11 # NetBSD 1.1,
options COMPAT_12 # NetBSD 1.2,
options COMPAT_13 # NetBSD 1.3,
options COMPAT_14 # NetBSD 1.4,
options COMPAT_15 # NetBSD 1.5,
options COMPAT_43 # and 4.3BSD
options COMPAT_386BSD_MBRPART # recognize old partition ID
options COMPAT_SVR4 # binary compatibility with SVR4
options COMPAT_IBCS2 # binary compatibility with SCO and ISC
options COMPAT_LINUX # binary compatibility with Linux
options COMPAT_FREEBSD # binary compatibility with FreeBSD
#options COMPAT_PECOFF # kernel support to run Win32 apps
# File systems
file-system FFS # UFS
file-system EXT2FS # second extended file system (linux)
file-system LFS # log-structured file system
file-system MFS # memory file system
file-system NFS # Network File System client
file-system NTFS # Windows/NT file system (experimental)
file-system CD9660 # ISO 9660 + Rock Ridge file system
file-system MSDOSFS # MS-DOS file system
file-system FDESC # /dev/fd
file-system KERNFS # /kern
file-system NULLFS # loopback file system
file-system OVERLAY # overlay file system
file-system PORTAL # portal filesystem (still experimental)
file-system PROCFS # /proc
file-system UMAPFS # NULLFS + uid and gid remapping
file-system UNION # union file system
file-system CODA # Coda File System; also needs vcoda
(below)
# File system options
options QUOTA # UFS quotas
#options FFS_EI # FFS Endian Independent support
options SOFTDEP # FFS soft updates support.
options NFSSERVER # Network File System server
#options EXT2FS_SYSTEM_FLAGS # makes ext2fs file flags (append
and
# immutable) behave as system flags.
# Networking options
#options GATEWAY # packet forwarding
options INET # IP + ICMP + TCP + UDP
options INET6 # IPV6
#options IPSEC # IP security
#options IPSEC_ESP # IP security (encryption part; define
w/IPSEC)
#options IPSEC_DEBUG # debug for IP security
#options MROUTING # IP multicast routing
options NS # XNS
#options NSIP # XNS tunneling over IP
options ISO,TPIP # OSI
#options EON # OSI tunneling over IP
options CCITT,LLC,HDLC # X.25
options NETATALK # AppleTalk networking protocols
options PPP_BSDCOMP # BSD-Compress compression support for
PPP
options PPP_DEFLATE # Deflate compression support for PPP
options PPP_FILTER # Active filter support for PPP
(requires bpf)
options PFIL_HOOKS # pfil(9) packet filter hooks
options IPFILTER_LOG # ipmon(8) log support
# Compatibility with 4.2BSD implementation of TCP/IP. Not recommended.
#options TCP_COMPAT_42
# These options enable verbose messages for several subsystems.
# Warning, these may compile large string tables into the kernel!
options EISAVERBOSE # verbose EISA device autoconfig
messages
options MIIVERBOSE # verbose PHY autoconfig messages
options PCIVERBOSE # verbose PCI device autoconfig messages
#options PCI_CONFIG_DUMP # verbosely dump PCI config space
#options PCMCIAVERBOSE # verbose PCMCIA configuration messages
options SCSIVERBOSE # human readable SCSI error messages
options USBVERBOSE # verbose USB device autoconfig messages
#options PNPBIOSVERBOSE # verbose PnP BIOS messages
#options PNPBIOSDEBUG # more fulsome PnP BIOS debugging
messages
options I2OVERBOSE # verbose I2O driver messages
options NFS_BOOT_DHCP,NFS_BOOT_BOOTPARAM
#
# wscons options
#
# builtin terminal emulations
#options WSEMUL_SUN # sun terminal emulation
# different kernel output - see dev/wscons/wsdisplayvar.h
options WS_KERNEL_FG=WSCOL_GREEN
#options WS_KERNEL_BG=WSCOL_BLACK
# compatibility to other console drivers
options WSDISPLAY_COMPAT_PCVT # emulate some ioctls
options WSDISPLAY_COMPAT_SYSCONS # emulate some ioctls
options WSDISPLAY_COMPAT_USL # VT handling
options WSDISPLAY_COMPAT_RAWKBD # can get raw scancodes
# see dev/pckbc/wskbdmap_mfii.c for implemented layouts
#options PCKBD_LAYOUT="(KB_DE | KB_NODEAD)"
# allocate a number of virtual screens at autoconfiguration time
#options WSDISPLAY_DEFAULTSCREENS=4
# use a large software cursor that doesn't blink
options PCDISPLAY_SOFTCURSOR
# modify the screen type of the console; defaults to "80x25"
#options VGA_CONSOLE_SCREENTYPE="\"80x24\""
# Kernel root file system and dump configuration.
config netbsd root on ? type ?
#config netbsd root on sd0a type ffs
#config netbsd root on ? type nfs
#
# Device configuration
#
mainbus0 at root
#apm0 at mainbus0 # Advanced power management
# Tuning for power management, see apm(4) for more details.
#options APM_NO_IDLE # Don't call BIOS CPU idle
function
#options APM_V10_ONLY # Use only the APM 1.0 calls
#options APM_NO_POWEROFF # Don't power off on halt(8)
#options APM_POWER_PRINT # Print stats on the console
#options APM_DISABLE_INTERRUPTS=0 # Don't disable interrupts
# Basic Bus Support
# Plug-and-Play BIOS and attached devices
#pnpbios* at mainbus?
# mainboard audio chips
#ess* at pnpbios? index ? # ESS AudioDrive
#sb* at pnpbios? index ? # NeoMagic 256AV in sb mode
#wss* at pnpbios? index ? # NeoMagic 256AV in wss mode
#ym* at pnpbios? index ? # OPL3-SA3
# com port
# If enabled, consider changing "com0", "com1", and "com2" under "ISA
Serial
# Interfaces" to "com*", otherwise com2 will attach at pnpbios? and
there
# will be no com0. A side effect is pcmcia (and other) com? previously
# starting at com3 may attach as com1 or com2.
#com* at pnpbios? index ? # serial ports
# parallel port
# The above "com*" comments apply, cf. "lpt0" under "ISA parallel
# "printer interfaces".
#lpt* at pnpbios? index ? # parallel ports
#pckbc* at pnpbios? index ? # PC keyboard/mouse controller
#fdc* at pnpbios? index ? # floppy controller
# IDE controller on Toshiba Portege 3000 series (crippled PCI device)
#pciide* at pnpbios? index ?
# PCI bus support
pci* at mainbus? bus ?
pci* at pchb? bus ?
pci* at ppb? bus ?
# Configure PCI using BIOS information
#options PCIBIOS # PCI BIOS support
#options PCIBIOSVERBOSE # PCI BIOS verbose info
#options PCIBIOS_ADDR_FIXUP # fixup PCI I/O addresses
#options PCIBIOS_BUS_FIXUP # fixup PCI bus numbering
#options PCIBIOS_INTR_FIXUP # fixup PCI interrupt routing
#options PCIBIOS_IRQS_HINT=0x0a00 # PCI interrupts hint. IRQ 9 or
11
#options PCIBIOS_INTR_GUESS # see pcibios(4)
#options PCIINTR_DEBUG # super-verbose PCI interrupt
fixup
# PCI bridges
pchb* at pci? dev ? function ? # PCI-Host bridges
pceb* at pci? dev ? function ? # PCI-EISA bridges
pcib* at pci? dev ? function ? # PCI-ISA bridges
ppb* at pci? dev ? function ? # PCI-PCI bridges
# XXX 'puc's aren't really bridges, but there's no better place for them
here
puc* at pci? dev ? function ? # PCI "universal" comm. cards
# EISA bus support
eisa* at mainbus?
eisa* at pceb?
# ISA bus support
isa* at mainbus?
isa* at pceb?
isa* at pcib?
# PCMCIA bus support
pcmcia* at pcic? controller ? socket ?
pcmcia* at tcic? controller ? socket ?
# ISA PCMCIA controllers
pcic0 at isa? port 0x3e0 iomem 0xd0000 iosiz 0x10000
pcic1 at isa? port 0x3e2 iomem 0xe0000 iosiz 0x4000
tcic0 at isa? port 0x240 iomem 0xd0000 iosiz 0x10000
# PCI PCMCIA controllers
pcic0 at pci? dev? function ?
# ISA Plug-and-Play bus support
isapnp0 at isa?
# ISA Plug-and-Play PCMCIA controllers
pcic* at isapnp?
# CardBus bridge support
#cbb* at pci? dev ? function ?
#cardslot* at cbb?
# CardBus bus support
#cardbus* at cardslot?
#pcmcia* at cardslot?
# Coprocessor Support
# Math Coprocessor support
npx0 at isa? port 0xf0 irq 13 # x86 math coprocessor
# Console Devices
# ISA console
#pc0 at isa? port 0x60 irq 1 # pccons generic PC console
driver
# Keyboard layout configuration for pccons
#options FRENCH_KBD
#options FINNISH_KBD
#options GERMAN_KBD
#options NORWEGIAN_KBD
# pccons-specific options:
#options XSERVER_DDB # PF12 gets you into DDB when X is
running
#options XSERVER # X server support
# wscons
pckbc0 at isa? # pc keyboard controller
pckbd* at pckbc? # PC keyboard
# "opms" should not be enabled together with "pms" or "pmsi"
pms* at pckbc? # PS/2 mouse for wsmouse
pmsi* at pckbc? # PS/2 "Intelli"mouse for
wsmouse
#opms* at pckbc? # backwards compatible PS/2
mouse
vga0 at isa?
vga* at pci? dev ? function ?
pcdisplay0 at isa? # CGA, MDA, EGA, HGA
wsdisplay* at vga? console ?
wsdisplay* at pcdisplay? console ?
wskbd* at pckbd? console ?
wsmouse* at pms? mux 0
wsmouse* at pmsi? mux 0
pcppi0 at isa?
sysbeep0 at pcppi?
# Serial Devices
# PCI serial interfaces
com* at puc? port ? # 16x50s on "universal" comm
boards
cy* at pci? dev ? function ? # Cyclades Cyclom-Y serial
boards
cz* at pci? dev ? function ? # Cyclades-Z multi-port serial
boards
# ISA Plug-and-Play serial interfaces
com* at isapnp? # Modems and serial boards
# PCMCIA serial interfaces
com* at pcmcia? function ? # Modems and serial cards
pcmcom* at pcmcia? function ? # PCMCIA multi-port serial cards
com* at pcmcom? slave ? # ...and the slave devices
# CardBus serial interfaces
#com* at cardbus? dev ? function ? # Modems and serial cards
# ISA serial interfaces
#options COM_HAYESP # adds Hayes ESP serial board
support
com0 at isa? port 0x3f8 irq 4 # Standard PC serial ports
com1 at isa? port 0x2f8 irq 3
com2 at isa? port 0x3e8 irq 5
#com3 at isa? port 0x2e8 irq 9
#ast0 at isa? port 0x1a0 irq 5 # AST 4-port serial cards
#com* at ast? slave ?
#boca0 at isa? port 0x100 irq 5 # BOCA 8-port serial cards
#boca0 at isa? port 0x100 irq 5 # BOCA 16-port serial cards
(BB2016)
#boca1 at isa? port 0x140 irq 5 # this line is also needed for
BB2016
#com* at boca? slave ?
#tcom0 at isa? port 0x100 irq 7 # TC-800 8-port serial cards
#com* at tcom? slave ?
#rtfps0 at isa? port 0x1230 irq 10 # RT 4-port serial cards
#com* at rtfps? slave ?
#cy0 at isa? iomem 0xd4000 irq 12 # Cyclades serial cards
#addcom0 at isa? port 0x108 irq 5 # Addonics FlexPort 8S
#com* at addcom? slave ?
#moxa0 at isa? port 0x100 irq 5 # MOXA C168H serial card
(experimental)
#com* at moxa? slave ?
# Parallel Printer Interfaces
# PCI parallel printer interfaces
lpt* at puc? port ? # || ports on "universal" comm
boards
# ISA parallel printer interfaces
lpt0 at isa? port 0x378 irq 7 # standard PC parallel ports
lpt1 at isa? port 0x278
lpt2 at isa? port 0x3bc
# Hardware monitors
# LM7[89] and compatible hardware monitors
#lm0 at isa? port 0x290 # other common ports: 0x280,
0x310
# VIA VT82C686A hardware monitor
#viapm* at pci? dev ? function ?
#viaenv* at viapm?
# I2O devices
iop* at pci? dev ? function ? # I/O processor
iopsp* at iop? tid ? # SCSI/FC-AL ports
ld* at iop? tid ? # block devices
# SCSI Controllers and Devices
# PCI SCSI controllers
adv* at pci? dev ? function ? # AdvanSys 1200[A,B], 9xx[U,UA]
SCSI
adw* at pci? dev ? function ? # AdvanSys 9x0UW[D], 3940U[2,3]W
SCSI
ahc* at pci? dev ? function ? # Adaptec [23]94x, aic78x0 SCSI
bha* at pci? dev ? function ? # BusLogic 9xx SCSI
dpt* at pci? dev ? function ? # DPT SmartCache/SmartRAID
iha* at pci? dev ? function ? # Initio INIC-940/950 SCSI
isp* at pci? dev ? function ? # Qlogic ISP [12]0x0
SCSI/FibreChannel
#ncr* at pci? dev ? function ? # NCR 53c8xx SCSI (old driver)
siop* at pci? dev ? function ? # Symbios 53c8xx SCSI
pcscp* at pci? dev ? function ? # AMD 53c974 PCscsi-PCI SCSI
# EISA SCSI controllers
ahb* at eisa? slot ? # Adaptec 174[02] SCSI
ahc* at eisa? slot ? # Adaptec 274x, aic7770 SCSI
bha* at eisa? slot ? # BusLogic 7xx SCSI
dpt* at eisa? slot ? # DPT EATA SCSI
uha* at eisa? slot ? # UltraStor 24f SCSI
# PCMCIA SCSI controllers
aic* at pcmcia? function ? # Adaptec APA-1460 SCSI
esp* at pcmcia? function ? # Qlogic ESP406/FAS408 SCSI
# ISA Plug-and-Play SCSI controllers
aha* at isapnp? # Adaptec AHA-154[02
aic* at isapnp? # Adaptec AHA-1520B
# ISA SCSI controllers
adv0 at isa? port ? irq ? drq ? # AdvanSys APB-514[02] SCSI
aha0 at isa? port 0x330 irq ? drq ? # Adaptec 154[02] SCSI
aha1 at isa? port 0x334 irq ? drq ?
ahc0 at isa? port ? irq ? # Adaptec 284x SCSI
aic0 at isa? port 0x340 irq 11 # Adaptec 152[02] SCSI
bha0 at isa? port 0x330 irq ? drq ? # BusLogic [457]4X SCSI
bha1 at isa? port 0x334 irq ? drq ?
# The "nca" and "dpt" probes might give false hits or hang your machine.
#dpt0 at isa? port 0x170 irq ? drq ? # DPT SmartCache/SmartRAID
#nca0 at isa? port 0x360 irq 15 # Port-mapped NCR 53C80
controller
#nca1 at isa? iomem 0xd8000 irq 5 # Memory-mapped controller
(T128, etc.)
sea0 at isa? iomem 0xc8000 irq 5 # Seagate/Future Domain SCSI
uha0 at isa? port 0x330 irq ? drq ? # UltraStor [13]4f SCSI
uha1 at isa? port 0x340 irq ? drq ?
wds0 at isa? port 0x350 irq 15 drq 6 # WD7000 and TMC-7000
controllers
wds1 at isa? port 0x358 irq 11 drq 5
# CardBus SCSI cards
#ahc* at cardbus? dev ? function ? # Adaptec ADP-1480
# SCSI bus support
scsibus* at adv?
scsibus* at adw?
scsibus* at aha?
scsibus* at ahb?
scsibus* at ahc?
scsibus* at aic?
scsibus* at bha?
scsibus* at dpt?
scsibus* at esp?
scsibus* at iha?
scsibus* at iopsp?
scsibus* at isp?
#scsibus* at nca?
#scsibus* at ncr?
scsibus* at pcscp?
scsibus* at sea?
scsibus* at siop?
scsibus* at uha?
scsibus* at wds?
# SCSI devices
sd* at scsibus? target ? lun ? # SCSI disk drives
st* at scsibus? target ? lun ? # SCSI tape drives
cd* at scsibus? target ? lun ? # SCSI CD-ROM drives
ch* at scsibus? target ? lun ? # SCSI autochangers
ses* at scsibus? target ? lun ? # SCSI Enclosure Services
devices
ss* at scsibus? target ? lun ? # SCSI scanners
uk* at scsibus? target ? lun ? # SCSI unknown
# RAID controllers and devices
cac* at eisa? slot ? # Compaq EISA array controllers
cac* at pci? dev ? function ? # Compaq PCI array controllers
mlx* at pci? dev ? function ? # Mylex DAC960 & DEC SWXCR
family
mlx* at eisa? slot ? # Mylex DAC960 & DEC SWXCR
family
twe* at pci? dev ? function ? # 3ware Escalade RAID
controllers
ld* at cac? unit ? # logical disk devices
ld* at twe? unit ?
ld* at mlx? unit ?
# IDE and related devices
# PCI IDE controllers - see pciide(4) for supported hardware.
# The 0x0001 flag force the driver to use DMA, even if the driver
doesn't know
# how to set up DMA modes for this chip. This may work, or may cause
# a machine hang with some controllers.
pciide* at pci? dev ? function ? flags 0x0000
# ISA Plug-and-Play IDE controllers
wdc* at isapnp?
# PCMCIA IDE controllers
wdc* at pcmcia? function ?
# ISA ST506, ESDI, and IDE controllers
# Use flags 0x01 if you want to try to use 32bits data I/O (the driver
will
# fall back to 16bits I/O if 32bits I/O are not functional).
# Some controllers pass the initial 32bit test, but will fail later.
wdc0 at isa? port 0x1f0 irq 14 flags 0x00
wdc1 at isa? port 0x170 irq 15 flags 0x00
# IDE drives
# Flags are used only with controllers that support DMA operations
# and mode settings (e.g. some pciide controllers)
# The lowest order four bits (rightmost digit) of the flags define the
PIO
# mode to use, the next set of four bits the DMA mode and the third set
the
# UltraDMA mode. For each set of four bits, the 3 lower bits define the
mode
# to use, and the last bit must be 1 for this setting to be used.
# For DMA and UDMA, 0xf (1111) means 'disable'.
# 0x0fac means 'use PIO mode 4, DMA mode 2, disable UltraDMA'.
# (0xc=1100, 0xa=1010, 0xf=1111)
# 0x0000 means "use whatever the drive claims to support".
wd* at wdc? channel ? drive ? flags 0x0000
wd* at pciide? channel ? drive ? flags 0x0000
# ATAPI bus support
atapibus* at wdc? channel ?
atapibus* at pciide? channel ?
# ATAPI devices
# flags have the same meaning as for IDE drives.
cd* at atapibus? drive ? flags 0x0000 # ATAPI CD-ROM drives
sd* at atapibus? drive ? flags 0x0000 # ATAPI disk drives
uk* at atapibus? drive ? flags 0x0000 # ATAPI unknown
# Miscellaneous mass storage devices
# ISA floppy
fdc0 at isa? port 0x3f0 irq 6 drq 2 # standard PC floppy controllers
#fdc1 at isa? port 0x370 irq ? drq ?
fd* at fdc? drive ? # the drives themselves
# some machines need you to do this instead of fd*
#fd0 at fdc0 drive 0
# ISA CD-ROM devices
#mcd0 at isa? port 0x300 irq 10 # Mitsumi CD-ROM drives
# ISA tape devices
# note: the wt driver conflicts unpleasantly with SMC boards at the
# same I/O address. The probe reprograms their EEPROMs. Don't
# uncomment it unless you are actually using it.
#wt0 at isa? port 0x308 irq 5 drq 1 # Archive and Wangtek QIC tape
drives
# Network Interfaces
# PCI network interfaces
an* at pci? dev ? function ? # Aironet PC4500/PC4800 (802.11)
de* at pci? dev ? function ? # DEC 21x4x-based Ethernet
en* at pci? dev ? function ? # ENI/Adaptec ATM
ep* at pci? dev ? function ? # 3Com 3c59x
ex* at pci? dev ? function ? # 3Com 90x[B]
epic* at pci? dev ? function ? # SMC EPIC/100 Ethernet
esh* at pci? dev ? function ? # Essential HIPPI card
fpa* at pci? dev ? function ? # DEC DEFPA FDDI
fxp* at pci? dev ? function ? # Intel EtherExpress PRO
10+/100B
gsip* at pci? dev ? function ? # NS83820 Gigabit Ethernet
le* at pci? dev ? function ? # PCnet-PCI Ethernet
lmc* at pci? dev ? function ? # Lan Media Corp SSI/HSSI/DS3
ne* at pci? dev ? function ? # NE2000-compatible Ethernet
ntwoc* at pci? dev ? function ? # Riscom/N2 PCI Sync Serial
rtk* at pci? dev ? function ? # Realtek 8129/8139
sf* at pci? dev ? function ? # Adaptec AIC-6915 Ethernet
sip* at pci? dev ? function ? # SiS 900/DP83815 Ethernet
ti* at pci? dev ? function ? # Alteon ACEnic gigabit Ethernet
tl* at pci? dev ? function ? # ThunderLAN-based Ethernet
tlp* at pci? dev ? function ? # DECchip 21x4x (and clones)
Ethernet
#options TLP_MATCH_21040
#options TLP_MATCH_21041
#options TLP_MATCH_21140
#options TLP_MATCH_21142
vr* at pci? dev ? function ? # VIA Rhine Fast Ethernet
# EISA network interfaces
ep* at eisa? slot ? # 3Com 3c579 Ethernet
fea* at eisa? slot ? # DEC DEFEA FDDI
tlp* at eisa? slot ? # DEC DE-425 Ethernet
# ISA Plug-and-Play network interfaces
an* at isapnp? # Aironet 802.11
ep* at isapnp? # 3Com 3c509 Ethernet
ne* at isapnp? # NE2000-compatible Ethernet
tr* at isapnp? # IBM/3COM TROPIC Token-Ring
# PCMCIA network interfaces
an* at pcmcia? function ? # Aironet PC4500/PC4800 (802.11)
awi* at pcmcia? function ? # BayStack 650/660 (802.11FH/DS)
cnw* at pcmcia? function ? # Xircom/Netwave AirSurfer
ep* at pcmcia? function ? # 3Com 3c589 and 3c562 Ethernet
mbe* at pcmcia? function ? # MB8696x based Ethernet
ne* at pcmcia? function ? # NE2000-compatible Ethernet
ray* at pcmcia? function ? # Raytheon Raylink (802.11)
sm* at pcmcia? function ? # Megahertz Ethernet
wi* at pcmcia? function ? # Lucent WaveLan IEEE (802.11)
xi* at pcmcia? function ? # Xircom CreditCard Ethernet
mhzc* at pcmcia? function ? # Megahertz Ethernet/Modem combo
cards
com* at mhzc?
sm* at mhzc?
# ISA network interfaces
ate0 at isa? port 0x2a0 irq ? # AT1700
cs0 at isa? port 0x300 iomem ? irq ? drq ? # CS8900 Ethernet
ec0 at isa? port 0x250 iomem 0xd8000 irq 9 # 3Com 3c503 Ethernet
eg0 at isa? port 0x280 irq 9 # 3C505 ethernet cards
el0 at isa? port 0x300 irq 9 # 3C501 ethernet cards
ep* at isa? port ? irq ? # 3C509 ethernet cards
ef0 at isa? port 0x360 iomem 0xd0000 irq 7 # 3C507
ai0 at isa? port 0x360 iomem 0xd0000 irq 7 # StarLAN
fmv0 at isa? port 0x2a0 irq ? # FMV-180 series
ix0 at isa? port 0x300 irq 10 # EtherExpress/16
iy0 at isa? port 0x360 irq ? # EtherExpress PRO 10
ISA
lc0 at isa? port 0x320 iomem ? irq ? # DEC EtherWORKS III
(LEMAC)
#depca0 at isa? port 0x300 iomem 0xc8000 iosiz 0x8000 irq 5 # DEPCA
#le* at depca?
nele0 at isa? port 0x320 irq 9 drq 7 # NE2100
le* at nele?
#ntwoc0 at isa? port 0x300 irq 5 iomem 0xc8000 flags 1 # Riscom/N2 sync
serial
bicc0 at isa? port 0x320 irq 10 drq 7 # BICC IsoLan
le* at bicc?
ne0 at isa? port 0x280 irq 9 # NE[12]000 ethernet
cards
ne1 at isa? port 0x300 irq 10
sm0 at isa? port 0x300 irq 10 # SMC91C9x Ethernet
tr0 at isa? port 0xa20 iomem 0xd8000 irq ? # IBM TROPIC based
Token-Ring
tr1 at isa? port 0xa24 iomem 0xd0000 irq ? # IBM TROPIC based
Token-Ring
tr* at isa? port ? irq ? # 3COM TROPIC based
Token-Ring
we0 at isa? port 0x280 iomem 0xd0000 irq 9 # WD/SMC Ethernet
we1 at isa? port 0x300 iomem 0xcc000 irq 10
# CardBus network cards
#ex* at cardbus? dev ? function ? # 3Com 3C575TX
#fxp* at cardbus? dev ? function ? # Intel i8255x
#rtk* at cardbus? dev ? function ? # Realtek 8129/8139
#tlp* at cardbus? dev ? function ? # DECchip 21143
# MII/PHY support
dmphy* at mii? phy ? # Davicom DM9101 PHYs
exphy* at mii? phy ? # 3Com internal PHYs
icsphy* at mii? phy ? # Integrated Circuit Systems
ICS1890
inphy* at mii? phy ? # Intel 82555 PHYs
iophy* at mii? phy ? # Intel 82553 PHYs
lxtphy* at mii? phy ? # Level One LXT-970 PHYs
gphyter* at mii? phy ? # NS83861 Gig-E PHY
nsphy* at mii? phy ? # NS83840 PHYs
nsphyter* at mii? phy ? # NS83843 PHYs
qsphy* at mii? phy ? # Quality Semiconductor QS6612
PHYs
sqphy* at mii? phy ? # Seeq 80220/80221/80223 PHYs
tlphy* at mii? phy ? # ThunderLAN PHYs
tqphy* at mii? phy ? # TDK Semiconductor PHYs
ukphy* at mii? phy ? # generic unknown PHYs
# USB Controller and Devices
# PCI USB controllers
ohci* at pci? dev ? function ? # Open Host Controller
uhci* at pci? dev ? function ? # Universal Host Controller
(Intel)
# CardBus USB controllers
#ohci* at cardbus? dev ? function ? # Open Host Controller
# USB bus support
usb* at ohci?
usb* at uhci?
# USB Hubs
uhub* at usb?
uhub* at uhub? port ? configuration ? interface ?
# USB Mice
ums* at uhub? port ? configuration ? interface ?
wsmouse* at ums? mux 0
# USB Keyboards
ukbd* at uhub? port ? configuration ? interface ?
wskbd* at ukbd? console ? mux 1
# USB Generic HID devices
uhid* at uhub? port ? configuration ? interface ?
# USB Printer
ulpt* at uhub? port ? configuration ? interface ?
# USB Modem
umodem* at uhub? port ? configuration ?
ucom* at umodem?
# USB Mass Storage
umass* at uhub? port ? configuration ? interface ?
atapibus* at umass? channel ?
scsibus* at umass? channel ?
# USB audio
uaudio* at uhub? port ? configuration ?
# USB MIDI
umidi* at uhub? port ? configuration ?
# USB Ethernet adapters
aue* at uhub? port ? # ADMtek AN986 Pegasus based adapters
cue* at uhub? port ? # CATC USB-EL1201A based adapters
kue* at uhub? port ? # Kawasaki LSI KL5KUSB101B based
adapters
# Prolofic PL2301/PL2302 host-to-host adapter
upl* at uhub? port ?
# Serial adapters
# FTDI FT8U100AX serial adapter
uftdi* at uhub? port ?
ucom* at uftdi? portno ?
uplcom* at uhub? port ? # I/O DATA USB-RSAQ2 serial adapter
ucom* at uplcom? portno ?
umct* at uhub? port ? # MCT USB-RS232 serial adapter
ucom* at umct? portno ?
# Diamond Multimedia Rio 500
urio* at uhub? port ?
# USB Handspring Visor
uvisor* at uhub? port ?
ucom* at uvisor?
# USB scanners
uscanner* at uhub? port ?
# USB scanners that use SCSI emulation, e.g., HP5300
usscanner* at uhub? port ?
scsibus* at usscanner? channel ?
# Y@P firmware loader
uyap* at uhub? port ?
# USB Generic driver
ugen* at uhub? port ?
# Audio Devices
# PCI audio devices
auich* at pci? dev ? function ? # Intel ICH integrated AC'97
Audio
auvia* at pci? dev ? function ? # VIA VT82C686A integrated AC'97
Audio
clcs* at pci? dev ? function ? # Cirrus Logic CS4280
clct* at pci? dev ? function ? # Cirrus Logic CS4281
cmpci* at pci? dev ? function ? # C-Media CMI8338/8738
eap* at pci? dev ? function ? # Ensoniq AudioPCI
esm* at pci? dev ? function ? # ESS Maestro-1/2/2e PCI Audio
Accelerator
eso* at pci? dev ? function ? # ESS Solo-1 PCI AudioDrive
fms* at pci? dev ? function ? # Forte Media FM801
neo* at pci? dev ? function ? # NeoMagic 256 AC'97 Audio
sv* at pci? dev ? function ? # S3 SonicVibes
yds* at pci? dev ? function ? # Yamaha DS-1 PCI Audio
# ISA Plug-and-Play audio devices
ess* at isapnp? # ESS Tech ES1887, ES1888, ES888
audio
guspnp* at isapnp? # Gravis Ultra Sound PnP audio
sb* at isapnp? # SoundBlaster-compatible audio
wss* at isapnp? # Windows Sound System
ym* at isapnp? # Yamaha OPL3-SA3 audio
# ISA audio devices
# the "aria" probe might give false hits
#aria0 at isa? port 0x290 irq 10 # Aria
#ess0 at isa? port 0x220 irq 5 drq 1 drq2 5 # ESS 18XX
gus0 at isa? port 0x220 irq 7 drq 1 drq2 6 # Gravis Ultra Sound
pas0 at isa? port 0x220 irq 7 drq 1 # ProAudio Spectrum
pss0 at isa? port 0x220 irq 7 drq 6 # Personal Sound System
sp0 at pss0 port 0x530 irq 10 drq 0 # sound port
driver
sb0 at isa? port 0x220 irq 5 drq 1 drq2 5 # SoundBlaster
wss0 at isa? port 0x530 irq 10 drq 0 drq2 1 # Windows Sound System
#cms0 at isa? port 0x220 # Creative Music System
# OPL[23] FM synthesizers
#opl0 at isa? port 0x388 # use only if not attached to sound card
opl* at eso?
opl* at ess?
opl* at fms?
opl* at sb?
opl* at sv?
opl* at wss?
opl* at yds?
opl* at ym?
# Audio support
#audio* at aria?
audio* at auich?
audio* at auvia?
audio* at clcs?
audio* at clct?
audio* at cmpci?
audio* at eap?
audio* at esm?
audio* at eso?
audio* at ess?
audio* at fms?
audio* at gus?
audio* at guspnp?
audio* at neo?
audio* at pas?
audio* at sb?
audio* at sp?
audio* at sv?
audio* at uaudio?
audio* at wss?
audio* at yds?
audio* at ym?
# MPU 401 UARTs
#mpu* at isa? port 0x330 irq 9 # MPU401 or compatible card
mpu* at eso?
mpu* at fms?
mpu* at sb?
mpu* at yds?
mpu* at ym?
# MIDI support
midi* at clcs? # Cirrus Logic CS4280 MIDI port
#midi* at clct? # Cirrus Logic CS4281 MIDI port
#midi* at cms? # Creative Music System
midi* at eap? # 137[01] MIDI port
midi* at mpu? # MPU 401
midi* at opl? # OPL FM synth
midi* at pcppi? # MIDI interface to the PC speaker
midi* at sb? # SB1 MIDI port
midi* at umidi? # USB MIDI
# The spkr driver provides a simple tone interface to the built in
speaker.
#spkr0 at pcppi? # PC speaker
# TV cards
# Brooktree 848/849/878/879 based TV cards
bktr* at pci? dev ? function ?
# Mice
# ISA busmice
lms0 at isa? port 0x23c irq 5 # Logitech bus mouse
lms1 at isa? port 0x238 irq 5
mms0 at isa? port 0x23c irq 5 # Microsoft InPort mouse
mms1 at isa? port 0x238 irq 5
wsmouse* at lms? mux 0
wsmouse* at mms? mux 0
# backwards compatible versions
#olms0 at isa? port 0x23c irq 5 # Logitech bus mouse
#olms1 at isa? port 0x238 irq 5
#omms0 at isa? port 0x23c irq 5 # Microsoft InPort mouse
#omms1 at isa? port 0x238 irq 5
#opms0 at pc? irq 12 # PS/2 auxiliary port mouse
# Joysticks
#joy* at pnpbios? index ? # Game port
# ISA Plug-and-Play joysticks
joy* at isapnp? # Game ports (usually on audio
cards)
# PCI joysticks
joy* at pci? # Game ports (usually on audio
cards)
# ISA joysticks. Probe is a little strange; add only if you have one.
#joy0 at isa? port 0x201
# Miscellaneous Devices
# Planetconnect Satellite receiver driver.
#satlink0 at isa? port 0x300 drq 1
# Pull in optional local configuration
include "arch/i386/conf/GENERIC.local"
# Pseudo-Devices
# disk/mass storage pseudo-devices
pseudo-device ccd 4 # concatenated/striped disk
devices
pseudo-device raid 4 # RAIDframe disk driver
options RAID_AUTOCONFIG # auto-configuration of RAID
components
pseudo-device md 1 # memory disk device (ramdisk)
pseudo-device vnd 4 # disk-like interface to files
# network pseudo-devices
pseudo-device bpfilter 8 # Berkeley packet filter
pseudo-device ipfilter # IP filter (firewall) and NAT
pseudo-device loop # network loopback
pseudo-device ppp 2 # Point-to-Point Protocol
pseudo-device sl 2 # Serial Line IP
pseudo-device strip 2 # Starmode Radio IP (Metricom)
pseudo-device tun 2 # network tunneling over tty
pseudo-device gre 2 # generic L3 over IP tunnel
pseudo-device ipip 2 # IP Encapsulation within IP
(RFC 2003)
pseudo-device gif 4 # IPv[46] over IPv[46] tunnel
(RFC1933)
#pseudo-device faith 1 # IPv[46] tcp relay translation
i/f
#pseudo-device stf 1 # 6to4 IPv6 over IPv4
encapsulation
pseudo-device vlan # IEEE 802.1q encapsulation
# miscellaneous pseudo-devices
pseudo-device pty # pseudo-terminals
pseudo-device tb 1 # tablet line discipline
pseudo-device sequencer 1 # MIDI sequencer
# rnd works; RND_COM does not on port i386 yet.
pseudo-device rnd # /dev/random and in-kernel
generator
#options RND_COM # use "com" randomness as well
(BROKEN)
# a pseudo device needed for Coda # also needs CODA (above)
pseudo-device vcoda 4 # coda minicache <-> venus comm.
# mouse & keyboard multiplexor pseudo-devices
pseudo-device wsmux 2
and this dmesg
NetBSD 1.5W (GENERIC) #0: Thu Jul 5 00:51:44 UTC 2001
root@netapp:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: AMD K6-2 (586-class), 451.04 MHz
cpu0: I-cache 32 KB 32b/line 2-way, D-cache 32 KB 32b/line 2-way
cpu0: features 8021bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8>
cpu0: features 8021bf<PGE,MMX>
total memory = 127 MB
avail memory = 112 MB
using 1658 buffers containing 6632 KB of memory
BIOS32 rev. 0 found at 0xfb270
mainbus0 (root)
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled
pchb0 at pci0 dev 0 function 0
pchb0: VIA Technologies VT82C597 (Apollo VP3) Host-PCI Bridge (rev.
0x04)
ppb0 at pci0 dev 1 function 0: VIA Technologies VT82C598 (Apollo MVP3)
PCI-AGP (rev. 0x00)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
vga1 at pci1 dev 0 function 0: Silicon Integrated System 6326 AGP VGA
(rev. 0x0b)
wsdisplay0 at vga1: console (80x25, vt100 emulation)
pcib0 at pci0 dev 7 function 0
pcib0: VIA Technologies VT82C596A (Apollo Pro) PCI-ISA Bridge (rev.
0x12)
pciide0 at pci0 dev 7 function 1: VIA Technologies VT82C596A (Apollo
Pro) ATA66 controller
pciide0: bus-master DMA support present
pciide0: primary channel configured to compatibility mode
wd0 at pciide0 channel 0 drive 0: <IBM-DPTA-372050>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 19574 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 40088160
sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 4 (Ultra/66)
wd1 at pciide0 channel 0 drive 1: <QUANTUM FIREBALLlct20 20>
wd1: drive supports 8-sector PIO transfers, LBA addressing
wd1: 19470 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 39876480
sectors
wd1: 32-bit data port
wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
pciide0: primary channel interrupting at irq 14
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 4 (Ultra/66) (using
DMA data transfers)
wd1(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 4 (Ultra/66) (using
DMA data transfers)
pciide0: secondary channel configured to compatibility mode
wd2 at pciide0 channel 1 drive 0: <QUANTUM FIREBALLP LM20.5>
wd2: drive supports 16-sector PIO transfers, LBA addressing
wd2: 19595 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 40132503
sectors
wd2: 32-bit data port
wd2: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 4 (Ultra/66)
wd3 at pciide0 channel 1 drive 1: <QUANTUM FIREBALLlct20 20>
wd3: drive supports 8-sector PIO transfers, LBA addressing
wd3: 19470 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 39876480
sectors
wd3: 32-bit data port
wd3: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
pciide0: secondary channel interrupting at irq 15
wd2(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 4 (Ultra/66) (using
DMA data transfers)
wd3(pciide0:1:1): using PIO mode 4, Ultra-DMA mode 4 (Ultra/66) (using
DMA data transfers)
uhci0 at pci0 dev 7 function 2: VIA Technologies VT83C572 USB Controller
(rev. 0x08)
uhci0: interrupting at irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: VIA Technologie UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pchb1 at pci0 dev 7 function 3
pchb1: VIA Technologies product 0x3050 (rev. 0x20)
rtk0 at pci0 dev 11 function 0: RealTek 8139 10/100BaseTX
rtk0: interrupting at irq 10
rtk0: Ethernet address 00:00:b4:aa:c7:66
ukphy0 at rtk0 phy 7: Generic IEEE 802.3u media interface
ukphy0: OUI 0x000000, model 0x0000, rev. 0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isa0 at pcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
lpt0 at isa0 port 0x378-0x37b irq 7
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff: using exception 16
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
isapnp0: no ISA Plug 'n Play devices found
biomask fb65 netmask ff65 ttymask ffe7
Kernelized RAIDframe activated
warning: double match for boot device (wd0, wd1)
warning: double match for boot device (wd0, wd2)
warning: double match for boot device (wd0, wd3)
boot device: wd0
root device (default wd0a): rtk0
dump device:
file system (default generic): nfs
root on rtk0
nfs_boot: trying DHCP/BOOTP
nfs_boot: BOOTP next-server: x.x.x.x
nfs_boot: my_addr=x.x.x.x
nfs_boot: my_mask=255.255.0.0
root on x.x.x.x:/root/netbsd