Chris wrote:
> 
> Hiya,
> 
>     I recently brought home an old Zenith Zstation VP (486DX2/66, 16MB RAM)
> and added a WD 4GB HD, 3Com 3C509 NIC, SB 16 Pro compatible sound card and a
> PnP UDS IS11 SCSI card (Domex/DTC 436P/318x). I installed NetBSD 1.4.2 on
> it, but I've run into a few problems, basically:
> 
> 1.) I can't get X to come up. It's an onboard SVGA Cirrus Logic
> CL-GD5434-QC-F chip with 512k VRAM (I think, since there are two empty vram
> sockets). Now the XF86config file lists the 5434 as being an ISA card,
> however my dmesg output shows it being attached to PCI. I didn't find much
> useful info in the READme.cirrus file. When I try and start X, the screen
> switches resolutions, stays blank for about a second or two, then I get X
> server terminated 0:0 (explicit kill or something something). This may
> however be the fault of #2 and the VGA card may be working fine. (I have all
> video shadows disabled btw)
> 
> 2.) This system has an onboard PS/2 mouse and keyboard connector, but only
> the keyboard gets detected and attached (AFAICT). dmesg output posted at the
> end of the message. I have XF86 pointing to /dev/wsmouse0 , but nothing gets
> attached to that device.

Your mouse is on the opms device.  Make that your mouse device and see
what 
happens.

You should also use 'startx 2> errors > output' to check the server
status.  Check the errors file for the problems.  This works best from
the standard shell (you can do it from csh, but you'll need the specific
syntax for redirecting error output to a file).

> 
> 3.) The DTC 318x SCSI card gets detected (PnP), but says it's not
> configured. Does anyone know offhand if there is a driver running for it in
> -current or is it already written and I just have to compile it into a 1.4.2
> kernel?
>

I didn't see this controller listed in your output.
 
>     Any pointers or ideas at all would be helpful.
> 
>     Chris
> 
> : {2} /sbin/dmesg
> NetBSD 1.4.2 (GENERIC) #3: Wed Mar 15 23:41:54 PST 2000
>     toddpw@vader.toddpw.net:/usr/src/sys/arch/i386/compile/GENERIC
> cpu0: family 4 model 7 step 0
> cpu0: Intel 486DX2 W/B Enhanced (486-class)
> real mem  = 16384000
> avail mem = 11587584
> using 225 buffers containing 921600 bytes of memory
> mainbus0 (root)
> pci0 at mainbus0 bus 0: configuration mode 1
> pci0: i/o enabled, memory enabled
> vga1 at pci0 dev 12 function 0: Cirrus Logic CL-GD5434-8 (rev. 0xf9)
> wsdisplay0 at vga1: console (80x25, vt100 emulation)
> pchb0 at pci0 dev 16 function 0
> pchb0: United Microelectronics UM8881F PCI-Host bridge (rev. 0x01)
> pcib0 at pci0 dev 18 function 0
> pcib0: United Microelectronics UM8886 (rev. 0x01)
> isa0 at pcib0
> ep0 at isa0 port 0x300-0x30f irq 10: 3Com 3C509 Ethernet
> ep0: address 00:20:af:37:5d:8e, 8KB byte-wide FIFO, 5:3 Rx:Tx split
> ep0: 10baseT, 10base5 (default 10baseT)
> com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
> com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
> wdc0 at isa0 port 0x1f0-0x1f7 irq 14
> wd0 at wdc0 channel 0 drive 0: <Conner Peripherals 540MB - CFS540A>
> wd0: drive supports 16-sector pio transfers, lba addressing
> wd0: 516MB, 1050 cyl, 16 head, 63 sec, 512 bytes/sect x 1058680 sectors
> wd0: drive supports PIO mode 3, DMA mode 1
> wdc1 at isa0 port 0x170-0x177 irq 15
> wd1 at wdc1 channel 0 drive 0: <WDC AC24300L>
> wd1: drive supports 16-sector pio transfers, lba addressing
> wd1: 4112MB, 8912 cyl, 15 head, 63 sec, 512 bytes/sect x 8421840 sectors
> wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2
> lpt0 at isa0 port 0x378-0x37b irq 7
> sb0 at isa0 port 0x220-0x237 irq 5 drq 1: dsp v3.02
> midi0 at sb0: <SB MIDI UART>
> audio0 at sb0: half duplex
> opl0 at sb0: model OPL3
> midi1 at opl0: <SB Yamaha OPL3>
> pckbc0 at isa0 port 0x60-0x64            <--- I'm guessing it should be here
> pckbd0 at pckbc0 (kbd slot)
> pckbc0: using irq 1 for kbd slot
> wskbd0 at pckbd0: console keyboard
> opms0 at pckbc0 (aux slot)

  ^^^^^^^^^  Nope.  It's here.

> pckbc0: using irq 12 for aux slot
> pcppi0 at isa0 port 0x61
> midi2 at pcppi0: <PC speaker>
> sysbeep0 at pcppi0
> isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
> npx0 at isa0 port 0xf0-0xff: using exception 16
> fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
> fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
> isapnp0: no ISA Plug 'n Play devices found
> biomask c040 netmask c440 ttymask d4c2
> wscons: wskbd0 glued to wsdisplay0 (console)
> wd0: no disk label
> boot device: wd1
> root on wd1a dumps on wd1b
> root file system type: ffs