Hiya,

    I recently brought home an old Zenith Zstation VP (486DX2/66, 16MB RAM)
and added a WD 4GB HD, 3Com 3C509 NIC, SB 16 Pro compatible sound card and a
PnP UDS IS11 SCSI card (Domex/DTC 436P/318x). I installed NetBSD 1.4.2 on
it, but I've run into a few problems, basically:

1.) I can't get X to come up. It's an onboard SVGA Cirrus Logic
CL-GD5434-QC-F chip with 512k VRAM (I think, since there are two empty vram
sockets). Now the XF86config file lists the 5434 as being an ISA card,
however my dmesg output shows it being attached to PCI. I didn't find much
useful info in the READme.cirrus file. When I try and start X, the screen
switches resolutions, stays blank for about a second or two, then I get X
server terminated 0:0 (explicit kill or something something). This may
however be the fault of #2 and the VGA card may be working fine. (I have all
video shadows disabled btw)

2.) This system has an onboard PS/2 mouse and keyboard connector, but only
the keyboard gets detected and attached (AFAICT). dmesg output posted at the
end of the message. I have XF86 pointing to /dev/wsmouse0 , but nothing gets
attached to that device.

3.) The DTC 318x SCSI card gets detected (PnP), but says it's not
configured. Does anyone know offhand if there is a driver running for it in
-current or is it already written and I just have to compile it into a 1.4.2
kernel?

    Any pointers or ideas at all would be helpful.

    Chris

: {2} /sbin/dmesg
NetBSD 1.4.2 (GENERIC) #3: Wed Mar 15 23:41:54 PST 2000
    toddpw@vader.toddpw.net:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: family 4 model 7 step 0
cpu0: Intel 486DX2 W/B Enhanced (486-class)
real mem  = 16384000
avail mem = 11587584
using 225 buffers containing 921600 bytes of memory
mainbus0 (root)
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o enabled, memory enabled
vga1 at pci0 dev 12 function 0: Cirrus Logic CL-GD5434-8 (rev. 0xf9)
wsdisplay0 at vga1: console (80x25, vt100 emulation)
pchb0 at pci0 dev 16 function 0
pchb0: United Microelectronics UM8881F PCI-Host bridge (rev. 0x01)
pcib0 at pci0 dev 18 function 0
pcib0: United Microelectronics UM8886 (rev. 0x01)
isa0 at pcib0
ep0 at isa0 port 0x300-0x30f irq 10: 3Com 3C509 Ethernet
ep0: address 00:20:af:37:5d:8e, 8KB byte-wide FIFO, 5:3 Rx:Tx split
ep0: 10baseT, 10base5 (default 10baseT)
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
wdc0 at isa0 port 0x1f0-0x1f7 irq 14
wd0 at wdc0 channel 0 drive 0: <Conner Peripherals 540MB - CFS540A>
wd0: drive supports 16-sector pio transfers, lba addressing
wd0: 516MB, 1050 cyl, 16 head, 63 sec, 512 bytes/sect x 1058680 sectors
wd0: drive supports PIO mode 3, DMA mode 1
wdc1 at isa0 port 0x170-0x177 irq 15
wd1 at wdc1 channel 0 drive 0: <WDC AC24300L>
wd1: drive supports 16-sector pio transfers, lba addressing
wd1: 4112MB, 8912 cyl, 15 head, 63 sec, 512 bytes/sect x 8421840 sectors
wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2
lpt0 at isa0 port 0x378-0x37b irq 7
sb0 at isa0 port 0x220-0x237 irq 5 drq 1: dsp v3.02
midi0 at sb0: <SB MIDI UART>
audio0 at sb0: half duplex
opl0 at sb0: model OPL3
midi1 at opl0: <SB Yamaha OPL3>
pckbc0 at isa0 port 0x60-0x64            <--- I'm guessing it should be here
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
opms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
pcppi0 at isa0 port 0x61
midi2 at pcppi0: <PC speaker>
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff: using exception 16
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
isapnp0: no ISA Plug 'n Play devices found
biomask c040 netmask c440 ttymask d4c2
wscons: wskbd0 glued to wsdisplay0 (console)
wd0: no disk label
boot device: wd1
root on wd1a dumps on wd1b
root file system type: ffs